Jeff
Forum Replies Created
-
Houston Prevost Center is closest capable service center to you with lifts.
-
Display at Prevost Expo. Getting great response.
Company is Aqua -Air out of Ft. Lauderdale Fl. They will be crunching the numbers after the show and coming up with a price and first delivery date. -
I am guessing pressure cut out switch is going bad.
Chuck
-
Wanderlodge did it a little different, all 50A goes to a main panel, select loads were dual fed by the main panel and a inverter sub-panel utilizing a contactor which was biased towards the main-panel.
-
Bill,
Checked power at the Cruisair board = OK,
Checked power at the junction box by the evap unit = OK
Tried to run fan only (SMX) = fan does NOT come on
Evap for the galey is behind the fridge, have access to it thru an access door from the bathroom/toilet area, not enough to work on the unit/replace the fan assembly, will need to pull/slide the fridge out to get access.
Got a new fan sub-assembly(motor/wheel/enclosure)to replace.
The Galey Cruisair unit was rebuilt with new compressor, reversing valve(was leaking), capacitors, overload relay.
-
Jeff
MemberDecember 16, 2022 at 11:27 am in reply to: Buying Michelins from Prevost using PC discountThanks Bob!
Prevost has reasonably competitive pricing on their tires at the service center, (XZA2 Energy) and will sell just the tires without installation. But discounts don’t apply.
-
Condensing unit with new compressor is what is being configured. Basically the entire outside Cruisair unit is being replaced as a direct drop in replacement. The goal is to have the new system work with the old evaporator and control boards to offer cost saving alternates if you don’t want to replace the entire system. The company does have new evaporators and control boards if a complete update is desired. System has been designed on a CAD program and parts are being collected at this time.
No pricing is available yet. Pricing will be available by the time Prevost Expo arrives.
Chuck
-
Good Morning Chuck,
Was researching this issue and your 2020 post popped-up.
Have you been able to resolve this issue?
What all was involved?
My pocket door air cylinder is between the refrigerator and the tiled shower wall 🙁
My cylinder is Norgren brand and I can hear it hiss after operation. Initially I thought it was leaking indefinitely yet after operation, the hiss stops after about five minutes.
Do you recall your symptoms?
-
Bill: Something that none of us should ever see. Its kinda like looking at your own aorta or a kidney or a vertebra.
-
I have been doing that forever at 5000 mile (or less) intervals. It not only insures a dry pneumatic system is it a complete evaluation of the functionality of the air system check valves and protection valves.
If you have been servicing the air dryer regularly you should never ever see a drop of moisture any where in the system
-
Mike! What LED’s did you use for the dash lights? I believe they are 24v? That’s the only one’s I have not changed out
-
Guess no one knows the answer.
-
According to manual, UU code – Undervoltage Shutdown – Shutdown occurs if the voltage falls below 80% of the voltage regulator setpoint for more than 10 seconds.
Manual Says Check – Reduce load and restart
Of course i have flipped breaker off and tried, still UU code. Again when i do finally get it cranked and running i flip breaker back on. Runs fine. It’s all about getting it going. Plus, when it does throw th UU code it only fires for like a second or so, then stops and gives UU code.
Got a call into Kohler to see if they can help… Will see
I did see in manual where moving switch to OFF will reset controller, so code is being reset. Something is still not right in making controller throw that code intermittingly..
-
After replacing the two valves on two of the tanks on the left rear, I still had the left side go to 0 psi over a couple days, so I went ahead and ordered 6 more new ball valves to have enough for all 8 tanks. I don’t need to be anywhere for a few weeks, so I am dedicated to finding all of these leaks. I did happen to find a leak at one of the push-to-connect fittings going to a norgren.
Some of these leaks are hard to find because you really need to make sure you are saturating every single tiny part of the connection. I leak I just found recently, I know I went over it before and did not see anything.
It does look like I have 2 new-ish norgren valves, but the rest on the rear look quite old. I will probably replace the older ones just to avoid replacing them later.
I also ordered a decent amount of overstock/old-stock Swagelok 316SS fittings, tees, elbows, straight, 45’s, in 3/8 and 1/4″. Finding them on eBay makes these higher end fittings a bit more reasonable to purchase. So I am probably going to switch from “find and replace” to “replace it all”…