Michael
Forum Replies Created
-
Yes, the one I looked at years ago had a carrying capacity of 1,500 pounds. But that was many moons ago. I became a bit concerned when salesmen started to get evasive about actual coach weight.
Chris, it seems you have a coach that is very lightweight.
-
Jon raises a good point,
We’ve all maintained our residences, including plumbing, HVAC, electrical, roof, pool, appliances, A/C, water heater, furnace, house exterior, landscape, etc., but besides the generator (which I never had in my house), what else would be “unique” to maintaining in the “house” part of a Prevost, i.e. awnings?
-
thanks I tried logging out and back in checking my upper case lower case before I started this post and it did not
work but I just tried again and it worked. Thank you ,I don’t want to be a pain in your neck! -
The Holland Tunnel has a 12 foot 6 inch height limit and an 8 foot width limit. The Lincoln Tunnel has a 13 foot height limit and an 8 foot 6 inch width limit. The George Washington Bridge will get you there but it is a long trip depending on where you are going in Manhattan. Finding a place to park in the city is very difficult for a 45 foot bus and the police are typically not very understanding for blocking traffic.
-
Mr. TAG1: Did you buy that Country Coach from a guy in Kaukauna, WI?
-
Thanks a ton for the promt reply Al, as to bbq….both and it’s on us.
-
When does the No Rally Rally open?
-
Mark 109 is the red light point when it’s not good!!!!!
-
late sept would work best for me. should be making a pass through to give jeff some more money and would love to take part in this seminar.
-
Polishing stainless, either to touch up a repair, or to do an entire coach is not for someone that does not have training or skills.
While the process can be easily described, step by step, it will all boil down to the polisher using extreme care to avoid hurrying the process, and especially to limit or avoid heating the panels. Once a panel is overheated during the process it warps and looks very bad. Equally critical is uniformity. Every square inch of every panel needs the same amount of sanding and buffing so the quality of the finish is uniform.
Sanding???? Yes. use progressively finer grits, and before buffing end up with at least 1500, and if possible even finer grit. Then begin buffing, usually ending up with white rouge or a compound less agressive.
For those unskilled a good place to practice is on the raw aluminum wheels, and then if comfortable try buffing thicker surfaces like the stainless on the front bumper. Thicker surfaces are much more forgivving, and the smaller the surface the less uneven polishing is evident.
-
This past January, while at Jeff Rowe’s in Tennessee, I mentioned to Peter Campbell that it seemed I had to “chase” the steering wheel on our 16 year old, 70000 mile, new to us Prevost. Mentioned that Jeff had put new tires on the previous may. Peter said to get a three axle, laser alignment at a Prevost facility. We were headed to Florida so I made an appointment at Prevost Jacksonville for the alignment on our way back home.
Peter (and I think Jeff too) tried explained to me why the three axle alignment was important, but until the Prevost tech had the coach up on the alignment platform with the laser things hooked up and could actually explain to me what was going on did it finally sink in what was important. It was just like “stringing” a race car. Prevost (and me with the race car) start by establishing the parallel frame rails (Prevost uses center of the chassis). Then Prevost uses the laser (me strings on jackstands) to ensure that the wheels and tires are perfectly parallel to the center line of the chassis and hence that the axles are exactly perpendicular to the center line of the chassis (me the frame rails). If they aren’t, then shims are put in or taken out until axles are perpendicular/tires and wheels are parallel to that centerline.
In our case the tech first checked for any “play” in the front end and found one or more tie rod ends to be loose, so those had to be replaced first. The Prevost tech told me that is not uncommon, infact they had a whole set of them laying out before the coach was pulled into the bay and he was able to show me the play.
In our case, the drive axle was way out of alignment. The passenger side wheel tire was ahead of the driver side which would “push” the coach to one side, for which I tried to correct for, over correct, relax, and hence I was spending all my time “chasing” the coach with the steering wheel. The Prevost tech told me he has aligned many brand new coaches and while the new ones are “close”, they aren’t perfect. I asked if mine was “close” like a new one could be and he said “not by a long shot”, he took a stack of shims out of one side of the drive axle to get it perfectly alignment. I surmised that someone had “aligned” the coach at some point along the way. We never got service records with the coach so we didn’t know.
We also had new shocks put on all around; Koni’s on the front and regular Prevost (Monroe?) in back. I don’t think the shocks should impact steering on the straight and level.
I did notice immediately upon driving the coach on the road that I wasn’t chasing the steering wheel from one side of the road to the other, so the alignment must have solved that problem.
The Prevost tech told me that if you don’t get a quality laser alignment done by someone who knows what they are doing, the odds are good it won’t be a good alignment and you end up with what we had … badly out of alignment. Apparently if the alignment is done on a Hunter machine (not sure what that is although I’ve heard of Hunter machines) it tough to get it “right and precise”. The tech said if the alignment is done “by a truck shop that doesn’t know how to do a Prevost coach right”, you could end up with a bad alignment. I presume there are probably some truck shops with techs who know how do it right.
The tech did set the toe; with just a touch that would help the coach running in the far right lane with the pitch of the road to the right (i.e. a touch to the left to get it even). As I recall they started in back and worked to the front.
I wish I had the above great explanation by Grizz of the positioning and indexing of the steering wheel. That makes lots of sense to me. I would have asked the Prevost tech about that.
I probably shouldn’t even suggest this, but given the size of the tires and wheel base of the coach and not knowing if the axles were properly aligned I might try to check the alignment using string and jackstands just like on the race car. I suspect it might be a useful exercise to determine if axles weren’t square. The bigger the tires and the longer the wheelbase, the easier it should be so even small misalignments. If the rears axles aren’t perfect squarely to each other and the centerline of the coach, then something is wrong. That is as far as i would take it as I’m not about to start playing with the shims, even if Jon explained to me how to find them.
After leaving Prevost Jacksonville I realized I had forgotten to ask for and get a printout of the alignment both before and after the alignment job. Quite frankly this is what creates value for an alignment job. Whether its a $99.95 alignment at the Chevy dealer (which I recently had done on the HHR) or the $650 Prevost alignment, it all in the numbers. What did you find? Was it far off? How close were you able to get it to perfect. I had to ask the Chevy shop for the numbers, they didn’t offer it.
Reminds me of the time I took the drive shaft from the race car to an ancient drive line shop on Milwaukee’s north side across the street from the old A.O. Smith factory for balancing. When I picked it up there was a simple bill taped to it. I asked the guy at the counter how far off it was. He said “let me get Leo up here, he did the work”. A few minutes later scruffy, toothless Leo appeared and in great, articulate detail explained to me how he first had to straighten the driveshaft as it wasn’t perfectly straight, how he ground off the existing weights, and then balanced it. He asked what kind of a race car I was using it on and I told him a Cup car and would turn the engine up to 9200rpm. He said any vibration I sensed in the drive train was no longer attributed to the driveshaft. Leo created value by telling me what he did. The same thing goes for an alignment. Make sure you ask for the pre- and post-alignment numbers to see the value.
