Forum Replies Created

Page 36 of 214
  • Dick

    Member
    November 4, 2020 at 3:49 pm in reply to: Time to sell the bus !!

    I’m frustrated about the number of seriously prospective as well as current Prevost owners who are on any of the five or six Prevost Facebook sites who ARE NOT on the Previous Community Forum. I’ve been scolded, warned, and given “one last chance” for mentioning PC Forum and I’ve had a post recommending Prevost-Stuff and the PC Forum as good places to find pre-owned Prevosts deleted.

    Some of the information on those FB sites is pretty good, some is flat wrong (often because the person giving the information is very ignorant), and the rest is in the middle.

    This is consistently the big source for timely, fairly accurate information.

  • Dick

    Member
    November 4, 2020 at 1:53 pm in reply to: Windshield washer parts

    Joe,

    You have a part number for the module you mentioned?

    R

  • Dick

    Member
    November 3, 2020 at 8:22 pm in reply to: mac valve exhaust air leak

    Rebuild the air ram

  • Dick

    Member
    October 31, 2020 at 12:52 am in reply to: Catview application

    First, it apparently doesn’t work with Google Chrome as browser.

    Second, I’ve tried Microsoft Edge … but I get the same error message.

  • Dick

    Member
    October 30, 2020 at 11:15 pm in reply to: mac valve exhaust air leak

    raise the pressure to about 25 psi and I bet it stops. The valve specs show a minimum pressure. the valve does not move to close the exhaust without enough pressure.

  • Dick

    Member
    October 28, 2020 at 10:51 am in reply to: WHAT ARE YOU WAITING FOR??????????

    TSD…took the coach to Florida this past weekend…

    Fueled at TA, Michigan, Monroe, 10/23, 160gal, pump price $402, paid $335.

    Fueled at TA, Georgia, Lake Park(exit 2), 10/24, 150gal, pump price $377, paid $298.

    Summary: 310gal, pump price $779, paid $633, savings of $146, average $24/gal(this includes TSD/Pump miscellaneous fees)

    Prices at the pump at Lowe’s, Pilot, TA’s on I75 corridor $2.49 – $2.59, some places little lower, but not fitting my schedule to stop for fuel.

    Left Friday, 10/23, 8:30am from home, arrived 10:45PM at Lake Park, exit 2 in Georgia, approx 954 miles. Got some rain along the way but not a bad drive…

    Saturday morning, 6:30am started driving, arrived at Pelican in Naples 11:45am…, approx 384 miles.

    Life is Good!

  • Dick

    Member
    October 27, 2020 at 8:52 pm in reply to: Michelin tire service verses NTCS

    Colt! Great to hear from you again. Hope all is well. Sorry to hear you had a bad experience.

  • Dick

    Member
    October 26, 2020 at 5:18 pm in reply to: Accessing engine with Full closet in rear of Royal

    Well said Jon! Rule of the 6 p’s. Previous planning prevents p poor performance.

  • Dick

    Member
    October 26, 2020 at 1:24 pm in reply to: Accessing engine with Full closet in rear of Royal

    Is your coach A 40 foot or your closet is not as deep as mine. Bed not required to be removed. My engine completely under the closet

  • Dick

    Member
    October 25, 2020 at 9:32 pm in reply to: air ride system problems
    Crafty b, your bus has 3 major air systems: 1) “front brakes”, 2) “rear brakes”, 3) and last but not least “auxiliary” which is mainly for the air ride and leveling.
    There are a lot of sub-systems that operate off the “aux” system like your toilet, Detroit engine belt tensioners, generator air bags, step well cover, door lock, pocket door(s), dump valves, parking brake, air ride seat, etc. My bus has two air compressors, a Detroit engine driven one, and a 120vac for when the engine isn’t running. Your bus probably has these 2 also. Leaks are common and need to be minimized.
    The following is more info from my logbook that I got from PrevostService: Let’s start with where the air starts; the supply system. The heart of the supply system is the engine driven air compressor. It feeds an air dryer that removes moisture and oil. The dryer feeds the wet tank and a return line to the compressor mounted governor. The governor signals the air compressor to stop producing pressurized air and the dryer “sneezes” to unload the pressure line when the governor set air pressure has been met.


    The wet tank then supplies air to the front and rear brake main tanks and the auxiliary tank. To isolate the front and rear braking systems, air entering these tanks does so through a check valve at each tank. Once air is in the main brake tanks it cannot escape back into the supply feed.

    The auxiliary air system cannot have the same priority to supply air as the braking systems. To ensure the braking systems are fulfilled before the auxiliary system, the supply line is fed through a protection valve to the auxiliary tank. The protection valve opens when either side of the valve reaches a specific pressure which is somewhere between 60 and 75psi. If your coach’s air systems leak over time you may have noticed that air builds in the front(secondary brake) and rear(primary brake) systems first. At the rating of the protection valve you then hear the rush of air entering the auxiliary system.

    That is basically the entire supply air system. It supplies all 3 main air subsystems, rear braking, front braking, and auxiliary. Once those systems are filled the governor effectively turns off the compressor and each of the 3 systems are protected from their air returning to the supply air system.

    Let’s start with where the air starts; the supply system. The heart of the supply system is the engine driven air compressor. It feeds an air dryer that removes moisture and oil. The dryer feeds the wet tank and a return line to the compressor mounted governor. The governor signals the air compressor to stop producing pressurized air and the dryer “sneezes” to unload the pressure line when the governor set air pressure has been met.

    The wet tank then supplies air to the front and rear brake main tanks and the auxiliary tank. To isolate the front and rear braking systems, air entering these tanks does so through a check valve at each tank. Once air is in the main brake tanks it cannot escape back into the supply feed.

    The auxiliary air system cannot have the same priority to supply air as the braking systems. To ensure the braking systems are fulfilled before the auxiliary system, the supply line is fed through a protection valve to the auxiliary tank. The protection valve opens when either side of the valve reaches a specific pressure which is somewhere between 60 and 75psi. If your coach’s air systems leak over time you may have noticed that air builds in the front(secondary brake) and rear(primary brake) systems first. At the rating of the protection valve you then hear the rush of air entering the auxiliary system.

    That is basically the entire supply air system. It supplies all 3 main air subsystems, rear braking, front braking, and auxiliary. Once those systems are filled the governor effectively turns off the compressor and each of the 3 systems are protected from their air returning to the supply air system.

  • Dick

    Member
    October 25, 2020 at 9:02 pm in reply to: Royale Coach and Generators

    Have Jeff call me. He has my number. I just left there this morning! Another option for you is to send your TM102 (Silverleaf module back in your plumbing bay) to Silverleaf for reprogramming. I finally got to someone there who knows about this issue. Basically, there are two methodologies for remote generator starting.

    1). Send a signal to the generator to “start” for the duration you want the ginny to crank. (This is the older way of doing things – our generators are this type)

    2). Send a quick pulse (just a quick voltage on then off) signal to the generator, and it will do the rest.

    For whatever reason, our TM102’s (and John Browders is the same as ours) are set to the quick pulse-method #2, and need to be reset to method #1. Unfortunately, they need to go back to Silverleaf to do this.

    I just got my coach back from Jeff and am back in Nashville. I plan to send off my TM102 module on Monday or Tuesday for reprogramming. You might want to see how that goes before going through all the trouble of the latching relay.

  • Dick

    Member
    October 20, 2020 at 10:49 am in reply to: Questions about plugging in

    I leave my coach plugged in all the time now with the new inverters Magnums 2812 only 1 of the inverters I leave on charge while it’s sitting there. The new inverters will go into charge off mode till like 12.6v then back to 13.5 it bring them up then back down a bit. with both on they will never sink to go up and down. Un like the old inverters heart interface Xantrax inverters they will not be kind to batteries left charging all the time. And on chassis batteries I got rid of the old bread box charger 1 step and installed a 3 step 24v charger, I only charge them once and a while, When coach is sitting I keep knife switch off to chassis.

  • Dick

    Member
    October 19, 2020 at 5:21 pm in reply to: Questions about plugging in

    Thanks to your guidance, I found the ProMariner Gen 3 ProSport 12 charger on the ceiling above the chassis batteries. It has a 2018 date code on it, so it’s newish.

  • Dick

    Member
    October 17, 2020 at 5:37 pm in reply to: Wood Flooring

    Thanks guys. the only other think about laying plank is most people angle it.

    Makes the room look bigger.

    Later

    bv

  • Dick

    Member
    October 14, 2020 at 4:14 pm in reply to: Window Shade in Marathon

    Thanks, Buddy!

    Sounds like our daytime option may be to just open the existing Hunter Douglas shades on the side of the coach we want to see out…(away from direct sunlight during hot days/months). And, close them at night. 🙂

    Unless, just maybe, tonight’s Lottery ticket comes through! Deb’s been guaranteeing a winner for 32+ years…and, I believed her. Starting to have my doubts…but, why not us! Lightening might strike.

    Thank you,

Page 36 of 214