Jeff
Forum Replies Created
-
-
It is pretty straightforward. Swing the burner assembly out of the way-it hinges. Replace nozzle. While you have the burner open, make sure the ignitor tips are in the proper place (there is a gauge for that). Also make sure the flame detection window is not sooted up.
-
Thank you Don. I will try to get that one and change the sender if needed.
-
Bill, The beauty of owning our own buses means we can decide how and when to do maintenance. The coolant intervals are based on what Detroit or the coolant manufacturer says. You do what you want.
That applies also to transmission fluid changes, oil changes, tires, batteries, wiper blades, and everything else that is a service item.
I have been anal about coolant, engine oil and transmission fluid changes because the engine and transmission are 2 big ticket items and I do not want to risk problems.
About 8 years ago I heard a story I have never been able to verify of an owner that never changed his coolant for the 10 or 12 years he owned the coach. He had 42,000 miles on it when the engine failed due to cavitation of the cylinder liners. The story may have been BS, but cavitation is real and your can look it up on-line.
-
From owning a no slude H in the past, leaking could eother be the trapezoid window or up top where end cap meets main roof.
Isnt that the same paint job as George and Corey’s bus. I know when the bought their’s they said there was a twin.
-
I replaced the leaky air tensioner regulator on our bus 5 yrs ago with a <$50 unit from Tractor Supply.
-
Look for leaks around the trapazoid window or leaks from the seam between the front fiberglass cap and the bus roof. I have had both
-
Dick:
Looked at the hard copy owners manual I have in the coach and the online manual. Both have a wealth of know age, but found nothing specific to drive shaft installation/balancing.
Any thoughts as to how to confirm proper re installation of drive shaft.
Chuck
-
Chuck
Reason for not towing with trans in (N) is due to lack of lubrication inside transmission. Most if not all internal trans parts are lubricated by the transmission’s own internal pump (which supplies line pressure for shifts, clutches apply/release etc. This pump is driven (normally) by the input shaft via the torque converter – which is driven by engine’s crankshaft.
So in a towed situation (without the bus engine running), if you don’t pull axles or driveshaft, the output shaft on transmission continues to turn as the wheels roll – spinning internal transmission parts without adequate lubrication since bus engine and trans pump are not turning.
Hope that made sense. I can’t see any issue shifting to (N) while moving and off throttle, I would THINK the electronics would allow for smooth gear re-engagement when requested but haven’t tried that so not 100% sure. It has been no issue on any trans I’ve had with manual shift linkage, wouldn’t think electronic keypad would be a problem but again haven’t tried it.
-
Jeff
MemberJanuary 2, 2021 at 8:35 am in reply to: Suspension Squeak and engine compressor questionDog bone bushings.
-
What an amazing success story, congratulations to you and your daughter. Must be 2 peas in a pod.
-
Do you have information on how to contact them? If so, please share.
-
Larry, you headed to Desert Shores?
-
Jeff
MemberDecember 5, 2020 at 7:33 am in reply to: Kraus & Naimer C43 manual transfer switch repair?Chad, I cannot help you regarding where or if repair parts are available, but I vote for that option because our first Liberty was set up that way and the simplicity and robust nature of that switch was great. Option 2 would be to replace the entire switch as you mention.
An automatic transfer switch would just add a level of complexity that in my mind doesn’t get justified. As you are set up now nothing is simpler or as easy to use.
My first bus phone, permanently installed in my bus in 1990 was the “brick”. Keep in mind the folks here that pick on my lack of desire to have a smart phone were still playing with dolls and erector sets when I had a bus with a hard wired cell phone and a 5 foot satellite antenna on the roof.
-
Did you do it, and then verify push rod travel or did you trust the shop?