Dick
Forum Replies Created
-
A Christmas picture of Tom…

-
When I used the auto start if going to be gone all day I would chose the A/C’s that were not on the inverter circuit and would come back on with gen or shore restored. At least that’s the way it worked on my Marathons. If you chose A/C’s on the inverter circuit and the gen doesn’t start, the A/C’s will run the batteries down quick and the inverters will shut down at LBCO. Now you not only have dead house batteries, but the fridge and all other AC loads are dead.
-
Excellent, Harry! Merry Christmas to all. 🎄🎅🤶
-
Jim and Chris, if you want to switch buses, maybe we can console you a bit regarding the amount of risk you might be taking. When we switched from Liberty to Royale we:
1) went from no delamination risk to max delamination risk
2) no awning risk to max awning risk
3) no slide risk to max slide risk
4) minimum front axle risk to max independent front axle risk.
Maybe we have the riskiest pre emission model on the planet. Think of this if you balk at pulling the trigger. You may not be taking the most risk or are certainly not alone.
-
I think the Liberty installed accumulator tanks are perhaps 2 gallons? I’m guessing based on the ones I had and have seen. But the key is a manifold with home runs to shut off a fixture, and an accumulator plumbed to the inlet side of the manifold.
Playing a smart ass here, on my coach, and I bet all others I bet the water leak will stop quicker (by immediately turning off the pump and doing something like opening a faucet or flushing a toilet) than running outside to shut a valve. Get dressed, put on shoes, run down the stairs, around the side of the coach to get to the shut off valve, realize you forgot to unlock bay doors, run back to coach and hit the unlock button, run back to the bay, realize you forgot glasses, run back to get them, realize they were not where you thought they were, find them, run down the stairs, around the side of the coach, try to figure out which valve to shut.
Of course if you don’t use the coach water pump, but are relying on city water you add another element of frustration to getting the water shut off.
From now on I will just use the bathrooms, showers, and laundry at the campground and just leave my water turned off.
-
No manifold on our Liberty. I’ve seen them on other coaches, I think its a good idea. Its nice to be able to isolate a line at the source, but does it turn off the cold water to both sinks or just one? I think I could get a headache trying to figure out where to put the shut off valves and how to plumb the rest.
I like Jeff’s idea of the small hose clamp around the ice maker branch on the tee. That will strengthen things.
Good suggestion about not over tightening the nuts on the Flair-It fittings.
Also … I have yet to find the accumulator that some of you think I have. But I suspect there are a few panels I haven’t removed yet. Once I find it, I’ll let everyone know.
-
The 825hp applications were marine specs. The early units had some aftercooler sea water leak problems. Otherwise pretty solid. Shows that in a boat you should not cruise above 75-80% load if you want your engine to last.
-
Our Millennium will be finished in March. I could not be happier with the build process. Great team to work with.
-
came across this situation in 2012. Police notified. officer called back and told me he couldn’t give offender a ticket for stupid but got him for over width. (motor home in motion in that case)on 2 lane highway. No cure for STUPID!~
-
OMG The longer I’m around, the less things shock me. This actually got me!
-
Every time I’ve tried to use brass and plastic, it always leaks.
I don’t remember the name for the grey plastic, maybe Jeff will jump in here, but if I recall replacing it with the same stuff was unobtainable… If it’s Pex, you can get some of those fittings at the Depot or else use Sharkbite. Jeff?
-
You can always tell if a Liberty owner is in the campground, your nose will point you to the bus with the leaking aluminum holding tank.
-
Last time for me was 7 gallons also. Not sure of my sump size (I think it’s the small one), but I have retarder.
Which brings up an interesting question…sorry for the slight thread creep. I believe there is a higher capacity sump which, in theory, would lengthen the needed interval for fluid change and potentially keep fluid temps cooler and/or more uniform during retarder operation. Does anyone know what’s involved in changing to the larger sump?
-
Oh wasn’t aware of that one guess that will do lol I will definitely be there. Hope to see you there as well.