Forum Replies Created

Page 38 of 214
  • Dick

    Member
    September 28, 2020 at 8:31 pm in reply to: Help Identify this rotary switch

    Could it be aftermarket radar detector? I seem to remember one of those in a car. Has probably been removed and thus no effect when you turn it.

  • Dick

    Member
    September 23, 2020 at 12:14 pm in reply to: Stainless Polishing

    Hope he wears a mask. Those polishing compounds are not very compatible with biology.

    w

  • Dick

    Member
    September 22, 2020 at 1:26 pm in reply to: Led lights for h-9406

    Hey Jon, I think the years for the truck light are in the mid to late 80’s.

    Unless LMC has changed the gasket material, the gaskets will not work to seal the assembly to the flat surface of the bay doors. The cab lamps have a slight curve to them and the gasket they ship with the assembly is hard rubber and some what thin.

    The gasket material on my 99 CC was a soft spongy material that would fill the gap.

    The gasket will not seal the assembly on the two outer edges.

    You can use them and take a little black silicone sealer and seal the ends of the light housing.

  • Dick

    Member
    September 21, 2020 at 5:23 am in reply to: vision

    I fully agree with Al. Every coach regardless of converter has certain qualities or system designs. Just because one coach might have some differences doesn’t mean it is bad, just different. I am unaware of any coach that is not supported.

    Just learn about the coach you are buying in the respect to who has an understanding of it, can provide support, and who can work on it.

  • Dick

    Member
    September 20, 2020 at 2:41 pm in reply to: vision

    Yes, that is correct. You have to realize almost all conversation are to the specifics of the original owner.. some are for corporate, party, entertainer.and living. So it will take you some time to decide what you are going to use it for and proceed.

    Larry Nelson

    2002 XLII VISION

    Hurricane, ut

  • Dick

    Member
    September 18, 2020 at 3:34 pm in reply to: Excessive LEAN in curves while interstate driving?

    Jeff: Houston Prevost should (emphasis on “should”) be able to lift the coach and determine if there is something amiss with the front sway bar, links (Dog Bones), bushings, and even the shocks. A shock could have become unhooked or the bolt broke; in that case it would tend to roll over when turning in one direction versus the other direction.

    Al: A broken Panhard bar is very serious, since it keeps the drive axle centered under the coach. Although I’ve been under the coach a number of times when it was lifted, I can’t remember exactly how the rear suspension is designed. I think there are one or two links on both sides of the coach that align the drive axle, shocks, and the air bags plus the Panhard bar. If the Panhard bar is broken or unhooked, the drive axle is free to move right to left under the coach subject to whatever limits the links, shocks, and air bags provide … which given the weight and leverage aren’t very much! Acceleration and deceleration will cause the chassis to move from side to side and those parts listed could be bent, damaged, or even broken. My advice would have been to try not to drive it unless you absolutely have to and then not very far! Probably put it on a low-boy to get it to the shop.

    If you’ve watched enough NASCAR races you’ll eventually see a race car with a broken Panhard bar … one of the tires sticks outside the body about 6″ and the back of the car wiggles back and forth. In race cars the Panhard bar usually doesn’t break, but the mounting point on the rear axle or the frame is what breaks.

    From Wikipedia: A Panhard rod (also called Panhard bar, track bar, or track rod) is a suspension link that provides lateral location of the axle. Originally invented by the Panhard automobile company of France in the early twentieth century, this device has been widely used ever since.

  • Dick

    Member
    September 18, 2020 at 11:12 am in reply to: Water Hoses

    I use two 50′ Zero G foldable hoses which store easily in a cloth tote that hangs inside the water compartment. This allows the hoses to dry out and keeps them well away from the sewer hoses. These Zero G hoses are light years better than the old white ones I used to buy from Camping World. Those thing would leak within the first few uses and Camping World stopped honoring the warrantee on them.

    CC installed a spring roller for a standard water hose from the factory but it is faster and easier to use the Zero G hoses. We never leave city water hooked up and instead run off the fresh water tank. We once saw the impact on a coach near by when city water pressure burst a pipe inside while they were gone someone walking by saw water coming out the door and turned off the water but the damage was already done.

    I store sewer hoses both in the compartment over the drive and tags and in two 4″ tubes on the floor of a pass through compartment. The end cap has a hole drilled in it and the load side is open. The tubes are of a length that requires a push to get them all the way in. A 1/4″ chrome pin fits diagonally at the opening to keep the hoses in place. I built a ledge over those two tubes so lose little in the way of storage. From the cap end the area between the tubes makes for good storage of things with long handles.

    where we stay on the beach in Mexico the spots were laid out for pull trailers so when we head in to face the beach we have to run a long way to get to the sewer. This setup allow storing of 60′ of sewer hose without hassle, mess or loss of storage space in the bays.

  • Dick

    Member
    September 18, 2020 at 7:51 am in reply to: New shoes for the bus

    Include me among those who have expressed the opinion that some Prevost services are too expensive.

    But a comprehensive service such as what most owners get once a year involves a lot of materials, parts and labor hours if it is done as expected. I can say that because over the years I have done a full service on my coaches about 80 times now.

    My materials, including oil and all filters alone cost $200. Then there is my labor and I can easily spend 5 hours doing everything from lubing the chassis, checking the air system and tanks, replacing filters, dumping and refilling oil, and a myriad of other inspections and fluid level checks, including hubs and differential and power steering. I inspect belts, hoses, clamps and fittings, brake pads or shoes, discs or drums, as well as looking for evidence of leaks everywhere.

    If I find anything questionable or in need of repair or service that is added to my efforts.

    My point is to do just routine maintenance is a big deal in terms of time and labor, something Prevost or any service provider has to be paid to do. If I do not take the time to do all the little things I can be assured I will pay dearly for a failure to do all that is necessary.

  • Dick

    Member
    September 17, 2020 at 10:55 pm in reply to: Excessive LEAN in curves while interstate driving?

    Good Evening and thank you ALL for your input! Please excuse my delayed reply…was due to the fact we were on the road all day traveling from Angel Fire, New Mexico to Lubbock, Texas.

    My wife and I have been on the road since the second week of June and are now on the way home so I will definitely check all items mentioned very soon. I will report back if I find anything. Thank you again, Jeff

  • Dick

    Member
    September 17, 2020 at 8:24 pm in reply to: Excessive LEAN in curves while interstate driving?

    Dick – Marathon ordered the shell, 95 XL.

    Joel – good to know there were other leaners built.

    Sway bar appears to be avail according to parts manual. Not sure why ANY would be ordered without, unless for some strange reason on some specific chassis it wasn’t avail. This thing loves to lean.

  • Dick

    Member
    September 16, 2020 at 7:15 pm in reply to: Fastening subfloor

    That sounds like how we put a new wood deck on a flatbed truck and likely how you will have to proceed – slowly and tediously – hammer drill, then self-drilling screw to drive it home… do 10 hammer drills and 10 screws, then do it again… and again… and again… at least it’s not 105F in the shade.

  • Dick

    Member
    September 16, 2020 at 4:13 pm in reply to: 97 Liberty Webasto and Coach Heat Loop diagram?

    Slightly off topic…yet has anyone successfully adjusted the various Webasto valves so that when parked and operating, it creates a supply of unlimited hot water similar to how an Aqua Hot unit functions?

  • Dick

    Member
    September 15, 2020 at 4:12 pm in reply to: TSD & Love’s

    Jon, this summer we did 7,200 miles and I also searched out the TA on the road , however at times i was forced to a Loves and also complained about 20 g fuel , lol At those times I remembered the 40 plus i was paying in Ca a few years back and the constant 3.50 or so and being happy hahaha Man how times have changed .

    Prior to the card i knew every cheap/good fuel spot on the East coast . Thank the Lord those days are over 🙂

  • Dick

    Member
    September 14, 2020 at 10:20 pm in reply to: Indoor Storage

    Marshall, see if you can find an underutilized warehouse and make it work, new construction is expensive!

  • Dick

    Member
    September 14, 2020 at 7:45 am in reply to: Two General Discussions

    It is a glitch, has happened before and our web guru has to get his magic wand out of storage to fix it.

Page 38 of 214