Dick
Forum Replies Created
-
At about 65 lbs there is a pressure protection valve that opens and lets air into aux system. That said for some reason it sticks. I have found that if you fan brakes /with engine off until pressure drops close to zero on primary ( brake side then air up with engine again if sometimes releases and works as it should. I know nothing about how Liberty modified prevost level low. Do know if you have no pressure on secondary side your bags have no pressure in their supply side to operate in the first place. The purpose of the ppv is to give all available to brake system in case of a major air supply loss. Mine is located in front steer compartment (below drivers window -bottom one. On wall next to level low stack. Mechanical valves stick sometimes- maybe a slight tap will jar it loose.
-
The above comment is the exact mis-information people have to be aware of.
Extended life coolant that meets the spec is what is known as Organic Acid Technology and it has a 6 year life.
The other common coolant Inorganic Acid Technology coolants often ethylene glycol or propylene glycol are two year coolants and require occasional additions of SCA (supplemental coolant additives) to protect against pitting corrosion. If SCAs are added to OAT coolants they revert to a 2 year life coolant.
Whatever coolant you use is entirely up to you as an owner. The 2 year is cheaper, but entails 3 times the labor to maintain the system. The 6 year coolant is more expensive but only requires changing once every six years and changing coolant is time consuming and involves disposing of a large amount of used coolant.
Whatever is used however must be properly maintained according to the manufacturer’s recommendations. Coolant does far more than protect the engine from heat damage or freezing. It is the first line of defense against pitting and perforation of the cylinder liners. If that happens you are faced with a new or rebuilt engine.
Make the choice after reading and doing the research on what is best for you and your coach and be very carefull about advice from people who don’t know what they are talking about.
-
Hello,
My name is Steve Fowler and I am a facebook addict. Now with that said, We use Facebook in a big way to advertise my service business and the crane company. I too like Dick have reconnected with old friends that I had lost track of 30 years ago. I think it is a blast personally and it has made me money business wise. The addiction is real and like Ronald said, I would have a hard time leaving it…
Steve
-
I’m on FB. Wasn’t sure why in the beginning. Have found a number of friends I’d lost track of. Has also allowed me to connect with one or two organizations I find of interest, but wasn’t aware of.
I think that FB can be a very effective media for marketing events and organizations.
If my wife could get paid a “living wage” for being on FB as well as playing Candy Crush, Words with Friends, and some game where balls drop out of the top of her phone … I think I’d be interested in trading up to a newer Prevost five or sevens newer than our 1999.
Tom … if I post something to the PC FB page … is the post to the PC FB page seen by anyone who I’ve friended on FB outside the PC group?
-
http://www.bbc.co.uk/sport/0/ice-hockey/34730087
(Hope the link works). If not, look up Pittsburgh Penguins puck incident)
-
I think relatively few do work on their coach. I think the relatively small number (compared to the total population of owners) that post on this site are in the minority.
It is not because the owners are incapable, but they don’t have the tools, place, or trust in their knowledge. To many owners these coaches are intimidating and few really want to get into the nitty gritty of understanding all one has to understand before beginning to do work. I believe a lot of owners also lack the time to do the work.
Those of us that do our own work for the most part have an extensive history of messing with mechanical things. We change our own oil on our cars, we have spun wrenches in the past, and we just see the bus as big, not necesarily impossible to work on.
Then there is the issue of limits. Changing oil or fluids is one thing, but who has drain pans big enough, or a place to dispose of the fluids. That is a dirty, messy job and involves lifting heavy pails or drums and not a lot of people are willing to deal with the mess.
-
I have no long term experience with extended life but I have used it and can share the following.
First, go over the entire coach and replace any coolant hose that has the potential to be a problem before six years is up. It makes no sense to go to the trouble or expense only to find in a year or two you have burst a hose or have to replace one.
I would only use a coolant that meets the EC-1 standard. Caterpillar designed that coolant and the EC-1 spec but now many manufacturers are offering coolant that meets that spec. I used Cat coolant.
Get blanks for the SCA cartridges or shut off flow to the existing ones until you can get blanks. Adding any SCAs to extended life coolant reverts it to a 2 year life.
I may have gone overboard but I started with an engine flush after I drained it. I ran the coach for about 1 1/2 hours with the flush in it and when I drained it the water was a greenish black. I never was able to drain 100% of the capacity of 24 gallons so I refilled and flushed it about 6 or 8 times and it drained and took about 18 gallons at a time. By the last drain it was still showing some pink even though between drain and fill cycles I ran it and brought it up to temperature to open the thermostat and operated the Webasto to make sure I was flushing the entire system.
My next coolant change on my coach will be extended life and I will be doing what I described above.
I tried to discuss coolant with the local Detroit dealer and all I got was attitude and an apparent lack of interest or knowledge so I have no idea if a Detroit extended life is good or bad. All they managed to do was piss me off.
-
I know some guys thru my biker connections that can collect the money, with interest. They work on a contigency basis, but the debtor, not the creditor, pays the cost of collection. Sometimes the fee is paid in money, sometimes not. Either way, the debtor gets to experience pain equivalent to the pain the creditor experienced while getting stiffed by a deadbeat.
Where is the gentleman located?
-
Alvie,
Jeff got hosed, the bill isn’t paid regardless of what is on some other website.
-
Glen’s,
I have cranked my share of 2cyl John Deere’s in my day. Problem is, I don’t think Detroit makes a S-60 with 6 pet cocks!!Steve
-
Steve he did a super job.
My stainless looked good looking straight on at it but at an angle in the sun light it was not pretty. Lots of swirll marks.
Now it really looks good and shines even better than before.
-
Chuck,
I agree with Charles, 72 to Vonore, left on 411 and just before the bridge at the lake hang a left, you’ll see the big Prevost Communtiy and ETLC signs.
Hi to Barbie…
-
Mark thanks for the reply. I have tried cutting the power but it didn’t help. There are no control buttons on the outside face of the unit but there are some menu programming buttons and a power button on the back I found when I removed it from the Dash. I have now been told I can do a hard reset of the unit by pressing the power button for 5 seconds so I will try that tomorrow.
-
Just a heads up. We got the relay valve off last week but it looked nothing like the valves I got from NAPA. We cleaned the valve from the coach and found the p/n which matched the Bendix number. I made a second call to NAPA and they confirmed they sent me the correct valves and I looked online and confirmed the valves they sent me match what they have online. Again – they look nothing like the valve off the bus (and the ports are in the wrong spots) We made a quick call to Luke at US Coach and he had one on the shelf. He sent us a picture and it matched. Ordered it and installed perfectly and it works great.
We also found the hole in the powersteering line. It was crushed by the rear end. Apparently my bumpstops don’t stop the rear end from hitting the chasis. We spliced the line as I did not want to pull 40 feet of powersteering hose through the middle of the bus! Re-routed slightly to reduce the chance of it beeing crushed again.
Need to order up some new bumpstops! Add those to your LONG list of rubber things on a bus that age out 🙂