Forum Replies Created

Page 48 of 120
  • Peter

    Member
    August 19, 2015 at 9:43 pm in reply to: Appraisal

    It’s not the agents. It’s the underwriters. I insure vintage vehicles with an agreed value on several fronts from my bus to cars, motorcycles, airplanes and even my boat. They all require an appraisal or photos to insure at an agreed value above the “book” value. I’ve gotten used to it and am not offended. I suppose that if they weren’t careful about what they are insuring a person could place an inflated value on a junker and then sell it to them.

  • Peter

    Member
    August 19, 2015 at 9:02 am in reply to: Appraisal

    10 years ago had agreed upon value set on my coach. The insurance company provided the appraser. The person they sent knew nothing about a bus conversion. It could of been a school bus and it would of made no difference. She took pictures and looked at overall condition, sent info to insurance company and they accepted the value I was looking for. I think they just want “eyes on” the bus to verify overall condition and that it is what the are insuring.

  • Peter

    Member
    August 19, 2015 at 8:15 am in reply to: Any Recommendations in Maggie Valley, NC?

    You mean like this?

  • Peter

    Member
    August 18, 2015 at 9:04 pm in reply to: Any Recommendations in Maggie Valley, NC?

    I love Pans and Knucks..

  • Peter

    Member
    August 18, 2015 at 4:49 pm in reply to: GrandTetons Campground?

    I have stayed at two of the campgrounds run by the NPS in Grand Teton National Park.

    Gros Ventre is a first come fiirst serve gampground. They do have 10 spots with 50 amp service. In those spots out 45′ fit without problems. No water or sewer but both available in campground. We also stayed at Colter Bay Village RV Park. This is full service with reservation only. Tight to get in and out with many trees and unlevel surface.

    Both are nice, safe, and convient. I liked Gros Ventre better since had good cell phone reception and closer to Jackson etc. Moose wandered in and out of campground during May. Last year at Colter Bay had bears through campground.

  • Peter

    Member
    August 17, 2015 at 9:01 pm in reply to: H3-45 Window stile lights

    The box at the orange arrow is your Techlink computer and your light problem could be with Techlink. The Node Relays with the fuses are marked on the front with the corresponding function. I have had a red light before and the fuse was good. Have you tried a re-boot to see if Techlink will fix it? I cut the 12 and 24 house power to Re-boot.

  • Peter

    Member
    August 16, 2015 at 2:00 pm in reply to: Low Ride Height

    I am fairly confident of the following……..

    To have the bus air pressure reach 120 PSI, the aux system cannot leak faster than the bus engine compressor can build pressure. Once the protection valve between the brake systems reaches its normal open pressure of around 75 PSI all three systems build pressure simultaneously. If the bus is low and the system is set for driving the ride height valves will have an open path from the accessory air system and the air bags. That means as the engine driven compressor is trying to bring all three systems up to its cut out pressure the accessory system is allowing pressurized air into all air bags and all four air tanks and all 8 air bags are being filled simultaneously.

    The tag axle has nothing to do with any of this unless the lever was flipped, and if it was there would be a light on the dash and an audible alarm so that would not be overlooked. Unless the tag axle was to be lifted the lift chambers would receive no air, and the air path between the drive axle air bags would be open and the valve that exhausts tag axle air bag air would be closed.

    Brakes will always have their pressures satisfied. If there is a leak downstream from the primary, secondary and wet tanks, and assuming the protection valve works the brakes will have at least 75 PSI. That is true even if the leak in the accessory system is so big the accessory system cannot build any pressure, such as a blown air bag.

    It is my understanding there is another element that has not been discussed, but does explain how brake pressures could be at 120 and the accessory air to be at such a low pressure to be unable ot inflate the front air bags sufficiently. The Liberty coach has a “spitter” that discharges moisture whenever the aux compressor cycles. The spitter cup was not secured properly and it was leaking and preventing the aux compressor from reaching its set point and cycling off. I think that was the leak that prevented the accessory system from fully pressurizing.

    So here I go sticking my neck out a country mile and offering what I conclude as a potential answer. Jeff has to sign on for this and offer his opinion.

    The tag axle leak is a red herring. It had nothing to do with the issue, but was just a problem that was found as a result of diagnosing. For now, ignore that issue completely.

    The problem was the leak in the “spitter” prevented the accessory system from maintaining air pressure. But the leak was only a part of the problem. In order for air to flow into the accessory system it has to pass through the protection valve. But air pressure can build in the brake systems faster than in the accessory system if the protection valve is restricting the flow especially if it has been damaged by moisture. Since primary and secondary air system pressure controls the compressor governor the pressures could easily be 120, but because of a restriction of flow into the accessory system due to the leak in the spitter that system could not build to a pressure great enough to raise the front.

    Here is where I am making a bold diagnosis without all the facts………I suspect the coach has had moisture in the air system(s), the protection valve has corrosion and is failing to open sufficiently to raise the front because air was leaking out faster or at the same rate it was coming in. The coach has been repaired, but I would be surprised if an examination of the protection valve did not reveal it needs to be replaced also.

  • Peter

    Member
    August 14, 2015 at 1:58 pm in reply to: Tire Temperature

    I hope everyone who monitors both tire pressures and temperature understands that how the system is set up can impact the accuracy.

    For example, if the tire pressures are not set to the pressures listed in the Prevost or Michelin tire pressure charts that will create variations between temperatures. The initial tire pressure settings have to be correct and the weight on the tires determines those pressures. If you want to use the recommended pressures as the initial setting and then add 5 PSI at least you are being somewhat consistent and it will keep readings more uniform.

    Once you have consistency in your tire pressures relative to the charts, then to get consistency in the temperature readings you must be consistent with the sensor location. I know a lot of folks prefer to use extensions on the inner drive axle valve stems. But if the sensor for the TPMS is located on the end of a valve stem extension it will never report the temperature accurately. First you cannot remotely monitor the temperature of the air in or the tires themselves. It is no doubt better than having no information, but still will have an error so large as to be useless.

    If you intend to rely to an extent on the sensor reading tire temps, at least get the sensors as close to the tire or wheel as possible, and make sure it is in a location consistent with other sensor locations.

  • Peter

    Member
    August 14, 2015 at 8:11 am in reply to: Allison over full

    Steve, in that nicely cooled garage don’t forget to open the doors and windows while idling to warm up the trans temperature. That will let the diesel dust excape without doing bodily harm to you. Of course that nicely cooled 75 degree air will also excape making you warmer too!

    The above will be true unless you happen to have one of those flexible hose thingies that go thru a hole in the garage door to put all that diesel dust into the atmosphere.

  • Peter

    Member
    August 14, 2015 at 7:10 am in reply to: Tire Temperature

    Don’t panic Buddy. If you have a heat gun, check the temps then compare to the Pulse readings to verify the temps are correct. It’s possible the sensor is off.

  • Peter

    Member
    August 12, 2015 at 10:17 pm in reply to: Polson

    I know Tom had mentioned earlier about him and Jon springing for pizza in polson, but with the killing they’re making off of dues I’m thinking filets and lobster.

  • Peter

    Member
    August 11, 2015 at 5:50 am in reply to: Recovered chairs

    He’s supposed to set a good example. Where is his seat belt?

  • Peter

    Member
    August 7, 2015 at 9:40 pm in reply to: Major engine issues. Need advice

    Jeff picks it up in the morning and plans to look over the liners etc and talk to the guy who did all the work. Hopefully that will give us some more info. I too would like a definitive answer as to what led up to the failure.

    chris

  • Peter

    Member
    August 6, 2015 at 5:43 pm in reply to: Bus Barn

    Just a few thoughts.

    I agree with FFF that you need to really consider entry to the pit. Steps take more room than one might think and could change the length of the barn. At the same time you need to consider the depth and width of the pit. If it is too narrow, you will not be able to reach the edges of your bus. To deep and you will not be able to reach any part of your bus without a ladder. To shallow, and you will not be able to see your bus because you will be bent over. So it partially comes down to your height.

    When I built a pit in my garage, I made the depth my height 6′-4″. (not good for someone 5′-4″ but great for me) That way I could reach the bottom of my vehicles without having my arms fully extended. At times I still needed a 9″ step stool to reach some areas. I also made the width 4′-0″. That way I could reach my brake adjusters without crawling half way out of the pit and could still have a buddy down there with me.

    I also agree with the angle iron along the top edge of the pit. However, when I built mine, I used a 1 1/2 inch angle iron with one edge level with the floor and the other edge smooth to the pit side wall. Before I poored the floor, I welded 2″ bolts to the peak of the angle iron at 24″ on center. That way when the floor was poored, the angle iron was locked into place for life. At the same time it left a smooth surface for the 2×10 decking that I used to cover the pit. The smooth surface was also very useful when slidiing the 2×10’s back and forth. In addition I built a 2′-0″ x 4′-3″ tray with 4 wheels running in the direction of the 2′-0″ sides. I could load up the tray with all of the tools I may need along with a work light and rolled it down the pit to where I needed it. The one improvement I would make to the tray would be to shorten it up a bit and recess it into the pit 9-12″ because I needed the step stool to find the tool I wanted.

    I would also recommend that you plum the pit for both electrical and air. I installed my air about 1/4 the way down the pit at each end with the electrical every 4 feet the entire length of the pit fully recessed in the wall. You could use long hoses and extension cords, but I found that having these services readly available was well worth the effort.

    And lastly, I would recommend that you plot out where your jack points will be when your bus is parked and plan to strengthen the floor at these points. You could do that by adding rebar or making the slab thicker or both. Maybe I am just over cautious, but putting that much weight on a bottle jack …….

  • Peter

    Member
    August 3, 2015 at 8:36 pm in reply to: Bus Barn

    Based on our RV rental bldg (picture below) and keeping in mind a reasonable budget.

    Bldg size 20′ X 60″. The 60 feet length would be inside length. 14 Ft overhead insulated electric operated garage door. Side entry in and out door. 200 amp electric meter box at front, water service at front, sewer dump 25 feet from overhead entrance door. Concrete inside min. 6 inch. Front apron 6 inch. Lighting overhead front to rear. Two (2) 8 foot lights each side appox 10 feet high.

    The reason to have utilities in front is safety. Keeping the side wall clear will prevent bumps and bruises. Simply lay electric cord along side wall. Extending the bus part only a few ft to hook up. With this set up your unlikely to trip or hit something walking around the bus.

    Our bus is inside stall #1 on far right. Side entry door not visible in photo. Diesel pusher storage only. Tenant recently pushed a new Dutch Star…the whole bldg has that new bus smell.

Page 48 of 120