Jon
Forum Replies Created
-
George you need to replace the pic of the 98 to the new ride.
-
We have made some progress. Sheathing is on, insulated roof panels are on, and standing seam metal roof was just installed. I reworked the plan to put all the windows on the north facing side where my workbench area will be. We need to install a rain screen system with the siding, as well as the 18×13 garage door, and then rockwool insulation on the inside walls and ceiling, and of course paint. Electrical service is now run to the garage. I also got a manual-J sizing done, and it looks like it will only require 2.5 tons to cool and heat. I plan on keeping it climate controlled all the time.
-
Good for you, that’s the way to improvise. Nice job.
Later
bv
-
Fireside Resort on the 26th, then up to Mountainside KOA in West Yellowstone 27th,and 28th, then we are heading up to Townsend MT to Moochdock for a couple days with friends before we hit Devils Tower, Sturgis, and Mount Rushmore area.
-
w w williams came out friday. Unplugged ecm to check connections, plugged back in and it started once. Would not start on subsequent attempts. They wiggled wires and checked connections, no joy. They then plugged in a truck model ecm to test and the coach started normally about 10 times.
I’m spending the weekend at the beautiful Flying J resort here in Primm. Replacement ecm is expected tomorrow. They must program first then come back and install.
-
I got the Classic Mahogany and I love it.
-
The chassis used a monitor to light the dash idiot light to indicate an out of balance condition. There have been a number of owners who had to replace that monitor because it was faulty. When they got the dash light the 12 and 24 volt values were read on a meter and their values were OK so the defect was with the monitor.
In general terms the voltages with the engine running should be the 12 volt side should be exactly 1/2 of the 24 volt side within 1/2 volt or less. That can be checked at the terminals at the bottom of the equalizers.
Your description of the problem seems to indicate Vantare may not be using the monitor used by Prevost so if you do get an imbalance light for the house someone with Vantare knowledge may have to help you sort out how the Vantare system works so it can be repaired.
I cannot think of how it is set up except to say when the engine is running you are charging the batteries via the bus alternator, but when the generator is running you are charging via an on-board battery charger.
-
Dave:
Made note of all the settings you made. It’s got me very concerned about my decision to get another GC. Traded in a 2014 GC that had over 100,000 mile on the odometer and another 60,000 towed that didn’t show on the odometer. Never had a single problem with it, hence the decision to get another. I did read about a few problems people had with the new ones, but majority of reviews were positive. Of course I had to get the one with all the bells and whistles that I now understand cause a lot of the problems. Geeeeer
-
Good Job George
-
A stand alone GPS is simply ot necessary any longer. Online options are far superior and can give live traffic updates and speed trap warnings simply impossible by stand alone GPS unit.
U use Google Maps exclusively but some like WAZE or one of the software based rv units.
-
I too can have the engine cover off in a few minutes.
I did a thread here w/pics on the subject April of 23:
-
John nailed it. Follow his instructions.
Our 2021 GC has had the original software updated so we have power steering back immediately after coming out of the towing mode. I cannot speak about later models.
I do have the kit to keep power steering active while towing, something that eliminates the “death wobble”. But doing that will drain the battery in 3 hours so I added a Victron 24 to 12 volt charger and it is powered any time the bus is running. The kit has a toggle switch that needs to be turned on when towing, and off when not towing to keep the battery from draining.
I spent a year convincing Jeep Chrysler there were things within the software that needed to be changed and newer GCs may have those changes. Chrysler was so happy to have learned from an RVer what was required they extended my 2021 warranty to 2029. I hope the newer GCs have had the modifications.
-
In anticipation of a future or eventual need I had ETLC modify the Prevost engine cover so with 4 screws the top of the engine was exposed and there was no impediments to removing the valve cover.
Quite a bit of the cabinetry on and around the Prevost cover had to be removed to allow the needed work to be done. The bottom line however is that when I did need access to remove the valve cover and service the engine I had the needed access in 3 minutes.
I had repair work done by Prevost in Nashville and they were unaware how easy access was going to be. Normally their practice was to send the coach to a Nashville converter of entertainer coaches to disassemble the interior to the extent necessary, do the needed work, and then return the coach to the converter for reassembly.
I assured them that would not be necessary, and within minutes after pulling into the Prevost shop I had the cover off and what would have been a couple of days of work ended up being done in 3 hours.
Converters who build interior cabinetry over the top of the Prevost access panel should be spanked, and owners who do not anticipate the need and fail to make the modification I had done are exposing themselves to more costs than the cost of the needed modification.
-
I have been towing a 2023 GC 4xe for a year. It has been perfect. I did add a charge line, biut I have no idea if it is needed or not. I did turn off Auto Park Brake, but again, I have no way of knowing is it is needed. I think a big source of towing is people that open the drivers door during the process of going into neutral.
I always put in eSave mode, so the engine is running during the process, that seems to prevent the flashing “P” problem.
Here is the process I follow:
Hooking Up
- Hook up car to bus
- Reverse to lock tow bar
- Leave car running
- Keep doors CLOSED
- Confirm Parking Brake is (Make sure ”BRAKE” not showing on Instrument Cluster)
- Shift transmission into NEUTRAL
- Press and Hold “N” on transfer case with tool
- Confirm Transfer case in N (“N” Illuminated in orange at button)
- and (“NEUTRAL” showing on instrument cluster)
- Put transmission in PARK
- Confirm “P” not flashing on Console
- Shut off engine
Confirm TC indicated “N” by button - Remove foot from brake pedal
- Press START
- Confirm BRAKE not on
- Turn OFF Ignition
- Exit Vehicle
Unhooking
Press Brake Pedal
Start Vehicle
Put transmission in Neutral
Press “N” on Transfer Case
DONE