Jimmy
Forum Replies Created
-
Thanks Chad, An older bus can give us things to do for sure. But I’ve seen the same can be true of newer ones as well. There always seems to be something needing to be done. From a sliding door off the track to screws to be tightened and everything in between. I have a list of 11, most pretty easy, others a bit more troublesome. But all doable, I hope!
You mentioned maybe having your bus painted and I understand that’s a bunch of money? On the one hand it’s said you’ll never get your money back! But on the other hand if you like what you have then why not? It’s not as thought it’s going to depreciate anymore.
Harry
-
I’m not yet convinced the batteries are the problem.
The first thing I would do is verify the inverters are “on”.
My reason for starting with that is because almost all coaches have 2 inverters and even if one is not functioning the other is going to be working or at least should be.
The second thing I would look at is if in fact the inverters are powered up with shore or generator power I would want to see the setting for charging current. Some folks who dry camp and who use auto start for the generator use a high charging current like 40 or more amps. But others like myself use a very small charging current because I tend to be a power pole to power pole user and with a low inverter current like 5 or 10 amps I can run more electrical devices without concern about the power pole breaker tripping.
If all seems OK I would start the engine and see if the alternator is putting a decent voltage into the batteries. The alternator voltage output may not be adequate for complete charging, but it should show somewhere in the neighborhood of 27.5 volts.
The intent is to see what’s working and what is not. If batteries were so bad that they could not show more than the voltages listed when all charging current from inverters or alternator was removed they would go dead almost instantly. I am not saying a long life of undercharging may not have damaged the batteries, but doesn’t appear to explain the seriously low battery voltage.
As far as the current draw described I would consider that to be likely the result of phantom loads all our coaches seem to have, ranging from various things like alarms, clocks, power to retain the memory in the TVs or radios, all the various low power displays like the microwave clock, and even the power to systems like the Crestron.
-
There is a timer but it is based on inactivity. If you were working on a long post, unless you stepped away from the computer for a while it should not have timed out.
Having said that the same thing has happened to me and I know if i have to make a long response with time on another site to verify information or look something up I do the response in Word and then cut and paste.
Another way is to respond in shorter posts but with a couple or more, one after another.
-
Art,
Have you received a picture yet? If not I have taken one that I can email to you. Just reply to my email and I will send it out.
Doug
-
My dear Penny. I want you to know how saddened we are to hear of this. Roy and I have fond memories of visiting with you both at Lake Catherine and we were hoping to be able to meet up again. We are sending you all our love.
Martha and Roy Dameron
-
With out a doubt, Kyle Bennett is the best at Customer Service! Always eager to help in any situation. Their work is top notch!
-
Dont forget about the coaches with a Valid slide….no air pressure they leak…I am not sure what change was to the slide seal in 06….I have changed them in coaches that were 13 models and didnt see anything…I know that a change was made around 16 or 17…those seals are capable of being changed by removing the bladder only, the wipe seal portion stays in place
-
Jimmy
MemberApril 17, 2018 at 7:52 am in reply to: Detroit D60 Diamond Seal Leak Preventative MaintI presume this is not for an 8V92.
-
Dick of Detroit said: “Nice touch. They remind me of Jim Brunzell and Greg Gagne … The High Flyers. True legends.
It looks to me more like Sonny and Cher singing “I got you Babe”!
Harry
-
Big Al, would it not be a very “Hot” experience holding that exhaust pipe between your legs? I guess one would have to wear asbestos under wear!
-
WOW…you have earned the air leak finder of the month..
All kidding aside congratulations on all your success in finding air leaks and upgrading and a great post on PC
Arrow at Norgren valve shows I think an add on …you upgraded. Usually line runs directly to tank ..thus tank catches wet air. Now you have a pre filter drain plus a tank drain. Nice.
Keep eye on your daisy wheel drain valve…they are fine new. After a couple of years the inside ball will not 100% seal against cup face.
-
Tom,
I had to change out mine in my 04H3 Marathon about a year ago. Had issues first with the VGA box then several mos later the PC. Had Marathon in Fl. replace with the same. It was $1,200 to $1,500 I think. There really wasn’t a viable option for me other than spending a bundle to upgrade the whole system. So replaced and it has worked perfectly so far. PS mine is under the bed easy access.
KT
-
Jimmy
MemberMarch 17, 2018 at 12:17 pm in reply to: PC Emergency and Assistance Map – Needs Your HelpWe are listed now if we get approved that is.
-
Huh. We continue to learn something (from Jon) every day on the PC Forum.
I didn’t think about the engines being powder coated. I’ve seen the pictures of rebuilt engines that Brian Stanton posts to FB in bright blue. I wonder how American Fleet finishes those engines. Power coat? Paint?
Can paint be applied to powder coat and be expected to stick? Is there good adherence of the paint to the cured powder coat?