Jeff
Forum Replies Created
-
In my opinion I would like to know what it is, what it does being broke I always think about possible fire ,short could all go bad ,just me.good luck.
-
Fred, Judy,
We will arrive on 8/23. Look forward to seeing you. Just a few others that we know of will be there.
-
Rich appearing motorhomer and “broke” trucker..
-
Put new XLEZ’s on ours last year. Replaced the 2011/2012 dated XZA2’s. Honestly can’t tell any difference, still rides like a pillow.
Supposedly the XLEZ’s are an “updated/advanced” tire according to Michelin dealer. The XZA2’s (as of last year) were still available from Prevost due to the fact they were USA made.
The XLEZ’s came from Germany and France. Once the XLEZ’s are mfg. here I’m guessing that’s what Prevost will sell also.
These are the X LINE ENERGY Z’s Bill mentioned above. I just abbreviated.
-
If all is well with the items mentioned previously,
IMO, the most likely cause of your problem is:
low on freon. Connect AC gauges and see what is what. Find the leak and fix it(easier said than done). Compressor clutch shaft seal may be the problem. Look for oily residue.Other causes could be:Evap or Cond relay is bad causing associated fans not to come on so resulting in a hi or low pressure safety switch activation(this has happen twice to our bus)orDryer filter is clogged causing safety pressure switch activation(this happened to our bus a couple of yrs ago),orBad safety switch,orunloader valve(s) not operating properly. -
OK replaced our belt tensioner regulator we got from Mira Loma. Of course then it needed to be set. We added a dial gauge and have regulator set at 52. Arriving yesterday from Valve Check in Minnesota were new 6203-1MM-1NPt check valves. Got an extra one as spare.
Arriving today wAS our 3A-74 single belt which is 1.88 inches wide which has 3 V grooves on underside to replace the triple AX-74 belts going on the triple pulley on engine to Junction box for radiator fan and A/C dash compressor
Looked great until I started the bus. How much wiggle or untrueness in a belt is acceptable. Seems to me, the belt should be truer. With Triple AX-74’s all runs smooth. The wider belt I was told was better at staying on when air tensioners are flat. Part of the experiment freshly starting engine, I released the air I added from our garage compressor to see how the belt traveled. It bagan to ride up on the junction box side of system Hit rear stop button shutting motor down. Took belt off and reversed it by repositioning 180 degrees and reinstalled Same out come. Wanted to climb up off pulleys HMMM frowny face
I was hoping to do away with the triple AX-74’s Now maybe not. Napa had to special order the belt from Tennessee last week, from another supplier so I had to pay freight
-
Outlaw and Emerald are one in the same.
-
We have about 40 inches between our couch and built-in on the other side in our non-slide coach. At the most narrow it is 36 inches between the fridge and cabinet on the other side.
-
That is GREAT news, Mark – Gotta take advantage of any warranty!
Thank you for sharing!
-
In terms of “losing your mind” as the expression goes – we all had a “head start” when we bought our coaches!!!
I would love to see pictures of the special cart and engine on it.
Elite pulls a lot of engines every winter to repair frame rust on the rear clip – so if applicable, that would be a to-do.
On the Freon change – Prevost Montreal told me that every hose (including the ones running through the house) must be changed as the new gas deteriorated mine and clogged the system) Not sure relative to your year
I upgraded my fuel separator lid with the optional pressure gauge top so I could keep an eye out for clogs. But in researching, I saw a “how far should I go” item. They make a dual separator rig with a switch for boats. If you get a bad batch of fuel and are dead on the road (happened to me coming back from Canada) you just turn the knob and can keep going on the second filter.
Am envious of your work!
-
This is what I ended up doing. I pulled the engine and transmission and have it torn down for a complete overhaul in my garage. I borrowed a cart that was specifically made for the Prevost 8v92 to sit on and roll out the back. (pretty slick) I have a lot of time in it, but I have already learned a tremendous amount.
This has allowed me to go through the engine soup to nuts. I am rebuilding power steering pump, air compressor, replacing some of the air and fuel lines. I am also at the same time converting the R12 air conditioners to R134a. All A/C hoses and both compressors and associated pressure and temperature sensors are being replaced. Heads have been sent out for rebuild with new springs. Injectors will get checked out and refurbished as needed. Bearings, sleeves, pistons, gaskets, etc. all replaced. Front and rear main seals replaced. Turbo and blower will be inspected and gaskets replaced. Oil pressure regulator will get new spring and added washer to raise oil pressure at idle. Everything to get new paint. Radiator is coming out to get cleaned and pressure tested. Transmission inspected.
A couple of questions for you guys…
What else should I do while I have the engine and transmission out?
Have I lost my mind?
Any opinions on FP Diesel (Federal Mogul) vs. Interstate McBee vs. Detroit Diesel branded parts?
Have I lost my mind?
Do you know the paint color of the grey that the engine compartment is painted?
-
+1 what Buddy said for using Biobor. And make sure you have several sets of filters and a gallon or so of fuel to fill the spin on filter & top off the Racor if you have to do it on the road…just in case. Also make sure you have a pretty good filter wrench on board as well. The spin on filter will tighten as a result of engine heating/cool down cycles and can be almost impossible to get off on the side of the road if you don’t have a good wrench.
-
I was going to buy a Jeep GC as my next toad. After reading this it will not happen.
When I was shopping I told the dealer it would be towed behind the coach and not a single word regarding a power steering kit was mentioned. I am not going to go through what has been described.
I see an Equinox or something similar in my future.