Tim
Forum Replies Created
-
Mike,
I would love to have any Liberty manual I can get. Please post or email me the link and I will down load it. I use digital manuals as much as possible.
Thanks
-
I was likely under there at least 8 hr. Over a couple of days. Ran out of grease trip to NAPA. Pull one of the R-12 valves put it in a vice to remove the fittings and it slipped, crushing the threads on a fitting. Multiple trips to NAPA for a replacement fitting. Even with the part in hand and me telling them for nylon air brake lines, they ordered the wrong type and the wrong size. I finally looked up the part number in the gates catalog and got the right one. Too many compression fitting types and the nylon tube type is not listed in every gates catalog.still learning what to look for and hope I “see” what I’m looking at. I could have easily missed that kinked line.
-
I nearly spit out my drink!
-
I do coolant analysis annually. I use Oil Analyzers Inc. http://www.oaitesting.com/services.aspx
Preferred Amsoil customers pay $33ea, The general public pays $41.
Examples: Fleetguard WF2051 has 4 units of DCA2, or Fleetguard WF2151 has 4 units of DCA4. The threads on my spin-on adapter are 11/16-16-UN-2B
http://www.cumminsfiltration.com/pdfs/product_lit/americas_brochures/LT15108.pdf
Does anybody have a simular pdf file by Detroit Diesel they could share with us?
-
When Prevost went ot the 18,000 lb front axle in 2004 we began using the Michelin 365/70R22.5 tire on a 10.5 inch wheel. The tires were necessary for the front axle rating but as you state they are not needed for the tag axle weight we carry on the shells. It was done so that there would be a spare tire to use if you lost a front tire for any reason. The 365 was less available then than now and Prevost was the only manufacturer using the tire.
The reasoning was that you could move a tag tire to the front axle and then install a 315 on the rim of the damaged tire to get you home. Or you could have the tire service bring you a 315 mounted on a 9 inch steel wheel, also to get you home safely. While it may seem that the 315 would not fit on the 10.5 inch wheel, Michelin told us it was possible for those times when a 365 was not readily availbale and you had to continue on.
This was also the time we changed the wheels from “stud- mounted” to “hub-mounted” style that Michelin required on the 365. It also changed us to the more common truck tire setup (hub-mounted). That is also why the studs on the hubs need to be changed when you go to the 365 tires.Presently all the wheels are hub mounted on all axles.
Safe Travels!!!!
-
The manual ZipDee awnings work fine for Me. Don’t want no Air actuated nothing else to worry about. The large one over Our Outdoor Grill and entertainment center is great. You can keep it low to shade more or raise it up.The window Awnings help keep the coach cooler by shading the Single pane windows.
-
Well I don’t have that gurgling sound in my three other evaporators. Also, I have some moisture on the floor under my Galley evaporator, which I don’t believe should be wet.
-
An evaporator is always going to have moisture because its temperature is colder than the air passing through it so the humidity in the air condenses on the evaporator and typically drips into a tray below the evaporator. The tray will have a drain so the collected moisture can drip on the ground outside.
-
You are right Jon I did not like the air awning so I just put a window awning on, I could have put a manual one on but I don’t use it so had the window awning put on and I like those, you can’t even tell it had the big awning on
-
I think Tom’s answer was in the context of an XL, but the reality is we all need the number of batteries that will allow us the use of our bus as we intend for it to be used.
-
Jack finch had a 2008 made with 6 8Ds and there is two more I know of
Mine has 4. 8Ds but will have 6 8Ds. soon
-
Tom,
Far from the truth …
But Geo,
Did love Lisa (Zsa Zsa) in Green Acres!
-
Jon, thanks for the Alco wheel infro. I was not standing close to the wheel but it looked like he put a few drop of oil on the top of the stud thread. If I understood the Alco information, the torque should have been less that he 475 , 300-400. I may be slightly over torqued.
Roy
-
I always thought all torque values are based on DRY clean studs.
However I read the Alcoa wheel manual and the use of any oil or lubricant requires care, so much so Alcoa issues a warning.
Do not allow lubricant on the ball seat or beneath the cap nut head. This is mentioned on section 4 of the manual listed below.
https://www.arconic.com/alcoawheels/catalog/pdf/servicemanual-english.pdf