Robert
Forum Replies Created
-
Seven roof airs at a conservative 15 amps each is 105 amps, a HW tank is about 10 amps, but figure high at 15, water pump, inverters, TVs, outlets, range, etc might add another 50 amps so if you have everything running at once a 20 KW generator is more than ample.
Why downsize? Our generators are the healthiest when we keep them loaded. The engines are sized to handle the loads so when one is running with almost no load on the engine it impacts the injectors, increasing the potential for needed service. I’d add up all the loads and see how much generator capacity is really needed and size the generator based on that. In this case more is not necessarily better.
-

Had suspension etc will try later..
-
thanks guys ,its charging and the battery was junk. Just replaced the chassis batteries today too. turns out that the ” new” batteries were new in 2007. Gee I thought all salesmen were honest ! LOL thanks for the advice.
-
It’s mounted to the floor plywood above the holding tank, he didn’t mean it was mounted to the tank itself. The pump on my 2001 is exactly in the same place as was my 94. Liberty does a good job with flexible connections so the PVC pipes can be removed to make access to the pump easier. I did both mine without removing all the pipes, not easy, but doable.
-
Alvie,
Its not powered by Ford 🙂
And Jerry got it right, its a SBC. The cost to have built that with Ford parts would have been 1.5 – 2 times more expensive, and that motor cost more than I will ever admit to 🙁
-
We have said it before, and will continue to say it. No matter if you have ramps or a pit do not ever get beneath the coach unless it is supported at the chassis support points.
Never ever. Don’t do it.
The only time it is safe to be beneath the coach without the chassis being supported is if the chassis has been lowered fully.
Hydraulic jacks are not proper support unless they are all the way down. Even a hydraulic jack can fail.
-
Sure your guys are on top of it ; The new inverter style gen sets are smaller in size and are much more dependable plus easier to stack for back up.. Fwiw. I have even went to Inverter 48 V dc in my Ac /heat system and cut amp load by 2/3rds… But ck out the possibility of the differant Gen sets on the market now. Just food for thought.
Still supply standard 120/220 60 hz supply to coach.
-
Hello,
Yes to all your questions, I was just wondering if there was a way for me to get a jump on them.A service oriented kind of thing that I know what is going on even when I am not there!!!!Thanks,
Robert -
Michael,
WOW….Thanks, for the information and especially the pictures. There is a lot of shinny metal, impressive motor install.
welcome to PC
AL
-
Looks nice your ramps, Can you rework those norgens ?
-
I forgot to mention Steve’s Neoplan now has a 14 liter Series 60 that he installed himself to replace what i think was a 2 stroke Detroit. These folks think nothing of gutting the interior and redoing it or replacing the drivetrain.
Steve’s Neoplan was built in the US around 1992. Next to him was Lou’s European Mercedes version the he totally rebuilt.
I should have taken photos of the interior that Lou did in that coach. Fantastic.
-
Like an idiot as soon as I looked at the ceiling and stuck out my tongue I knew I had been had.
-
I don’t and won’t! There are many, many campgrounds that make you park a trailer in a overflow type lot and even those that don’t many times have sites that are not large enough. Plus as other have mentioned, weight is BAD.
I pull a full size Tahoe, and that is as big as I want. We have to unhook even that many times just to park at campgrounds that don’t have sites large enough, or require you to back in.
One more thing that hasn’t been brought up is brakes. Pulling a heavy vehicle / trailer will make your stopping distances longer unless you have a properly working and adjusted braking system. I have seen many that don’t and it scares me to think that if they have to stop quickly, they may not be able to do so.
-
Thanks for the complements. I’m hoping for 10 MPG but I suspect 8 or 9 will be more likely. Even with a Variable Geometry Turbo boost pressure is still related to engine load / throttle position even at a steady RPM. I’ll check next time I’m driving it but I think I was seeing around 30 PSI at full throttle in 10th at 1400 RPM. I’ve only put about 60 miles on it so far and I seen low 40’s boost PSI if stretch out the RPM’s between shifts. I’m anxious to take it up Mount Eagle, (I’m near Nashville TN ) to see how it performs up a long grade. Speaking of Eagles, there is an Eagle Rally here in May, They say everyone is welcome. I’m planning on stopping by at least Saturday, maybe Sunday too. There is more info about the Rally on the MAK board.
Ken


