Forum Replies Created

Page 9 of 48
  • Jon

    Member
    February 19, 2024 at 8:46 am in reply to: Victron 24v charger

    Too much charging amps on a battery is not good for them long term. I tend to stick with a charger in the 5amps to 10amps range. The lower the better as long as it will keep your batteries fully charged. They do taper down the amps as the battery state of charge goes up, so the difference in 8 and 12 amps is probably insignificant.

  • Jon

    Member
    February 15, 2024 at 8:54 am in reply to: Still cannot determine why all 3 tanks drain

    Jon:

    Have drained tanks in sequence per your description, each remaining un drained tank held it’s pressure indicating check valves are working. My current conversation with Robert Hitt from Prevost indicated all 3 tanks can (slowly) leak down even with the check valve’s working properly. Robert said there are 3 sources where that can happen.

    *Parking brake

    *I believe it’s called a treadle valve. Valve under the brake foot pedal

    * R-12s

    Chuck

    P.S. Robert noted the R-12s are usually the culprit.

  • Jon

    Member
    February 6, 2024 at 11:48 am in reply to: Quartsite

    It’s a fun place meet a lot of good people, We always went with the Lemon group that is Fortravel people

  • Jon

    Member
    January 27, 2024 at 8:18 pm in reply to: Detroit power cool mixed with power cool Plus

    Incompatible formulas.

    Needs to be THOROUGHLY flushed.

    ***Your coolant filter is likely wrong now also. It should always be a “blank” filter for OAT coolant. I.e., contain NO supplemental coolant additives

  • Jon

    Member
    January 26, 2024 at 6:25 pm in reply to: What size (kw) is sufficient?

    MHO – I would replace with same Kw rating as was engineered and originally installed by the converter.

  • Jon

    Member
    January 19, 2024 at 11:04 am in reply to: XL belt-line problems

    Don’t forget to turn you spotlight around facing backward to avoid damaging the lens! Looks great, send more pictures!

  • Jon

    Member
    January 19, 2024 at 10:47 am in reply to: XL belt-line problems

    Mike

    looks great. Will you be at the Prevost Expo?

    Chuck

  • Jon

    Member
    January 17, 2024 at 8:08 pm in reply to: Air dryer for aux compressor?
    Pri & Sec brakes (brake tanks) take priority over suspension etc (aux tank), so there is a Bendix 75 psi PR-2 pressure protection valve, pt # 277227N, before the aux tank forcing the engine driven compressor to fill the primary & secondary brake tanks to 75 psi first. Then the PR-2 valve (see pic) opens and allows air to the aux tank (suspension etc).
    A lot of our Prevost didn’t come equipped with aux gauges, so you don’t know whats up with the suspension etc.
    Our Prevost have a lot of Bendix parts. Here’s a catalog of them: https://www.wanderlodgeownersgroup.com/downloads/BENDIX%20QUICK%20REFERENCE%20CATALOG.pdf
  • Jon

    Member
    January 17, 2024 at 11:55 am in reply to: Semi-urgent suspension advice needed

    3000 mile round trip went fine. I definitely still have some aux air leaks, but air suspension itself seems to be fine. First time towing a trailer as well (about 9500 gvwr w/ car) and also went fine.

  • Jon

    Member
    January 16, 2024 at 2:01 pm in reply to: Air dryer for aux compressor?
    In May of 2014 I removed the failing Gast brand 120v aux compressor and installed the California Air Tools MP100 – $200.
    Liberty installation of the Gast aux compressor was in the nose, behind the bumper, centered in the back behind the CruiseAirs. Accessed from underneath the bus, just forward of the solid axle , there’s a removeable panel. I installed the C A T MP100 in the same place, but I did build another box for it to live in.
    There is a Pumptrol brand 120vac adjustable pressure on/off switch. Remove the gray cover and you’ll see the nut/spring for adjustment
    There is also a 120vac Versa brand normally closed valve/solenoid to shut the air supply off. You can see the Versa between the air/water separators and gray Pumptrol switch.
    You can see my aux comp box in the back with its capacitor on it.(last pic)
    Your results may vary 🙂
    and
  • Jon

    Member
    January 9, 2024 at 10:31 am in reply to: TST tire monitor

    I have had the TST TPMS system since approximately 2010. I initially installed on my motorhome, I transferred the system to my bus in 2015.

    I installed a repeater in the bus because I had used it with my motorhome. I needed the repeater in my motorhome to maintain signal from the drive wheels and tags. I assumed I would have the same issue with the bus. The repeater is located in the bay with the chassis batteries and wired directly to them.

    TST changed the design of its sensors since I bought my system, and I recently discovered that they changed the design of the sensors again. The original sensors were lightweight and could be installed on rubber valve stems. I still use this style of sensors on my tow vehicle, but I am not sure they are still available. They are easy to install (except on inner drives) using the provided tool, which is designed to defeat the “security” feature intended to deter theft of the sensors.

    The new sensors are larger, heavier, and must be installed on metal valve stems. In addition, the new sensors did not interface well with my original monitor, so I purchased a replacement monitor. To install on the inner drives, I made a tool out of 3/4″ PVC pipe and a PVC coupler. It worked well until TST changed the design of the sensors again. My tool would not fit the new design. As I replace sensors, I install the new style sensors on the inner drives by threading by hand, which is possible to do between the tires if the drives are in the correct position (approximately the 5 o’clock position). Eventually, I will make a tool to install them when I eventually replace all sensors with the new style.

    The TST system has proven to be reliable and incredibly accurate. I have not used other systems that are on the market.

  • Jon

    Member
    January 8, 2024 at 11:19 am in reply to: Traveling in the single digits

    Was recently in Branson, MO in 20 deg weather. Didn’t do anything special. When driving the engine water circulates through the AquaHot and that keeps the water bay warm. When stopped I keep the AquaHot on keeping the water bay warm.
    you will find the AquaHot warms any gray, black or fresh water in the tanks helping keep the bay warm.
    Remember, Prevost is a Canadian company, they build them for the cold.
    Chuck

  • Jon

    Member
    January 5, 2024 at 9:18 pm in reply to: Headhunter flush issue

    With as much trouble it is to access, I recommend replacing the solenoid. The solenoid in our 96 Liberty 40Xl was in a much tighter area than yours. If it was a much newer solenoid, I would have taken it apart and cleaned it. I chose to replace it, I also guaranteed that I would never have another problem with it by relocating it to a much easier location to access. A previous owner had cobbled together a weird time delay module, so I had to replace it also. Figured I might as well replace the peizo switch also. At the same time I replaced the cheap water pump that was installed with a Mach5 pump, filter etc… Almost $3000 later we could actually flush the toilet with confidence.

  • Jon

    Member
    January 4, 2024 at 10:07 am in reply to: How do I open a locked bay door

    Cutting was the answer. Milwaukee makes a small M12 cut off tool with a narrow enough abrasive wheel to fit between the door handle and the side of the handle recess in the door skin. Took me two days and a did-not-show locksmith to get the courage to try, then five minutes to do the job. In my cases the electric actuator was frozen so the rod would not move when pushed or pulled. I don’t feel it necessary to lock that one compartment. All the rest work just fine. Thanks for all the suggestions.

    Jerry

  • Jon

    Member
    December 26, 2023 at 10:47 am in reply to: How do I open a locked bay door

    Thanks, i will try that.

    jerry

Page 9 of 48