Jon
Forum Replies Created
-
Thank you for the excellent write-up!
-
I pulled up the specs on the Toyo website and the 153’s are a true 10,000 lb tire can be used in any position,the 144’s is 9090 lb tire said it can be used in any position?
-
Filling up anywhere in Illinois is insane. I would purchase enough to get across the border then stop, walk the dogs, have a nice lunch and buy cheaper fuel.
-
EB has a series of You tube videos with him traveling around in the “Sun Bum” Bus. He had a Country Coach.
-
Hilger’s have Al’s old Coach.
Someone has Buddy’s.
Jon’s first two are out there somewhere
All of Tom’s seven are out there.
-
The reason I ask is because the voltage regulator (Transpo D443) has to be able to handle 270 amps, If that’s what the DN50 puts out.
-
Jerry: The electric solenoid for the airhorns on our coach in the steering bay, under the driver’s seat, driver’s side, ahead of the left front tire. Open the door and I find the solenoid near the floor of the bay at the front of the opening (near the lower door hinge). I’m not near the coach otherwise I’d take a picture for you. Mine stuck open, I had to use a Visegrips to shut the horn off, and then had it replaced with a quarter turn ball valve added to the discharge side.
I suspect my air horn solenoid was installed by Prevost and isn’t unique to the converter, so its very likely your solenoid is in the same place as ours.
Now idea on the step cover. I think that might be a converter installed item.
Good luck with your search!
-
What a great thread.
I am going through the same process in Sarasota, FL. I have my 3rd meeting today at 3:30 with the architect and GC. We are trying to build a 4 car garage with lifts for a total of 8 cars, living space with 2 offices (bedrooms after the final inspection) and 60ft undercover for the coach. I will know more this afternoon and I will post updates as they happen. We are planning a pretty high end, both indoor and outdoor kitchen, an indoor-outdoor shower and all with radiant heat.
Bill III
-
Yesterday I installed the new voltage regulator for the generator. I also replaced the individual exhaust gaskets also on the generator. As documented previously the generator started acting up over the last few times of use. It continually became worse over time.
The pictures should explain most of the process for the install. If anyone has any questions I will be happy to further explain. On my 1993 Liberty the VR was installed in the metal enclosure behind the gen motor. I replaced the the first regulator that lasted 25 years, less than 4 years ago. This was done at an event and not in the best of conditions. Considering that the entire unit needs to be mostly removed from the bus this made for a challenging repair, to say the least. The new VR from Powertec was nearly $500 and needed a fair amount of modification to the setup to be installed.
Since having issues again. I researched and found a VR with the same specs on Amazon for $47.59. AVC-63 4 The only exception is that the new one does not have a U/F adjustment. Yesterday, I built a several foot long, 4 wire, 10 gauge harness and moved the VR to a cooler vibration free location 2 compartments away. After installed I started the generator and let it get up to temperature. I noticed that Line 1 was showing 123 volts and Line 2 was 125. Prior to this install they ran 124 and 126. After a small, easy to access adjustment both were at a very solid 126. I then turned on all breakers including all 3 Cruisairs. It was in the 80’s here in FL yesterday. The generator ran very solid for 3 hours at exactly 180 degrees.
I am not advocating this VR for anyone else. I do not want to be responsible for any other members generator. However, for $48 I will order a backup to have in stock. The best part is I will now be able to replace it in 3 minutes (with a cocktail in hand) vs 3 hours of a major hassle.
I will be attending a Collector Car Auction in Punta Gorda, FL for several days next week. I will be using the generator most of the time, so this should be a good long term test. I will report back then.
Bill III
PS thanks to everyone that assisted in this project:)
-
Just to close out on this thread. It turned out that my charger had blown two fuses and was not charging the batteries so two of the batteries had been discharged when plugged into shore and sitting for a bit. That caused the imbalance. Once I got the charger working and batteries charged, all measurements are good and balance light is not coming on at all.
Also, the alternator is charging at 14.16 volts. Not sure exactly why it was showing so much voltage but obviously related to the battery issue.
Thanks as always!
-
Jeff, is your bed oriented “north/south” pointed towards the front of the coach? No access hatch under the carpet backer under the bed?
-
Just to set the record straight my last two Liberty coaches had a large cover over all the belts so a running engine posed no risk, and I removed them because with them in place there was no way to do a pre-trip inspection. I now have an engine compartment that is dangerous when the engine is running. Since I am usually the only person that will work in that area I take great pains to avoid loose clothing from getting caught in the belts of a running engine.
My 87 Liberty with the 8V92 had no belt covers and far more than my Series 60 coaches found me having to do work there with the engine running.
And even with my pit providing me relative safety when I am beneath the coach, I still will not go under it unless the chassis is supported on stands. I hate risks, but sometimes I have no choice except to be extra careful.