Jon
Forum Replies Created
-
Replaced my leaking surge/diaphragm tank.
-
I think your best and closest bet would be ClearwaterMotorcoaches in Clearwater. Geo.
-
Thank you Jon!
So 124.5V at the pedestal should be OK since south Florida is hot and the need/demand for A/C is obvious.
Then what would cause my inverters to display 126-130V if the input is 124.5V, just trying to understand?
I do have the Progressive Surge plugged in, there is no indication of any malfunction.
I am monitoring the readings from Michigan, looking at the variation, it make me uneasy…for example, I left 2 A/C’s ON with thermostat set to 80F, at 6:37AM – cooler temp outside, I assume the AC was not running – reading was 126V, at 11:00AM – at 78F outside, for sure A/C’s are running – reading is 129-131V.
Can the Power Co adjust the voltage down?
Is it possible the inverters are displaying erroneous voltage?
-
That is typical.
DDA states 1.5 psi per 100 rpms.
-
Flex Seal does not Flex or Seal. It’s simply “As seen on TV crap”!
Some Eternabond would hold it in place until you can find the necessary repair facility.
-
Do you have one of these?
High/Low Voltage Protection:
Whenever A/C power falls below 104 volts, or rises above 132 volts, the EMS automatically shuts down power to the RV. The EMS will monitor the power and once the AC power rises above 104 volts, or below the 132 volt level, the time delay indicator flashes for the present time and then automatically restores power to the RV.I don’t know why or how the 132 volt limit was established. Maybe one of the smarter guys have some insight.
I use the EMS-PT50X ever time I plug in, even at home. I don’t recall an over limit shut down. But we’ve experienced low limit interruption a few times at campgrounds; typically older campgrounds that had 50amp added long after original build out.
-
Captain Chuck,
Black ice is something that few come out of if they get on it. I have hit it a few times and came out of it because of doing the right maneuver.
Many moons ago coming down one of the 3 Sisters in Wyoming in the middle of the night in a curve and last time on a bridge outside of Little Rock.
Knowing outside temp is a must and if you get in a slide you have to step on the throttle to correct the slide OR proceed with extreme caution in the middle of the day.
You have handled huge boats in the ocean this is just a little frozen water.
Later
bv
-
Featherlite in Sanford, Fl rebuilt mine a few years ago. Two new compressors, two new fans, and a new PC board. Featherlite had a company reverse engineer the PC board and now has the new PC boards available (last time I checked $1,400). Problem is as with all newer electronics, they are not as robust as the old ones.
Took a couple of weeks to do (of course my coach wasn’t the only one they were working on) and cost a little over 6 G. Works well except in 98 deg days in direct sunlight. Have to fire up the Cruisair units to assist at that point.
Chuck
-
yes, stunningly beautiful, but $30K in deferred maintenance, owner with a ‘ain’t broke don’t fix it attitude’, zero documentation, with the price of a zero’d out museum show piece.
-
It is about the pre-treatment. Maybe some galvanic corrosion may contribute, but that is not the primary cause.
Over the years my factories had powder coating systems installed, including the last one I owned that had the Detroit Series 60 engine finishing system, and I would rather eat bees than put a finish, powder coating or otherwise, on aluminum because of the difficulties associated with finishing.
The car manufacturers that use aluminum body panels go through a lot of steps to pre-treat and apply a finish that will adhere forever.
-
You can call James Stallings at Xtreme Paint and Graphics about Prevost and aluminum painting and prep. The prep of an XL rivet bus requires each and every rivet to be detailed thoroughly.
I think Jon is spot on, again.
-
I have some of that on mine and it came from Yuma parked under a cover
-
Yes I need to have rain gutters up on cover that would help a lot, we haven’t had much rain in a few years so this storm we just got 3 inches Yahoo
-
Dick, glad you got it started. I’m just curious as to the outside (lowest) temps and if the block heater was used. Thank
-
Seems like an easy way to check ddec power is to flash the codes. Not only will it confirm power but tell you if there is a sensor issue. If good move to fuel.