Jim/Chris
Forum Replies Created
-
I have never heard that. I have heard that you need to keep a close eye on transmission temps because the retarder will raise fluid temps when it is being used. This may be a good one for Jon or Tom…have you guys ever heard of this?
-
you might try this
Programming a personal
entry codeThe factory set code cannot be reprogrammed but you can create
your own 5�digit personal entry code.
When pressing the controls on the keypad, press the middle of the controls to
ensure a good activation.Up to three personal entry codes may be programmed to the vehicle. To
create your own personal entry code:- 1. Enter the factory set code.
- 2. Within five seconds press the 1
� 2 on the keypad. - 3. Enter your personal 5-digit
code. Each number must be entered within five seconds of each other. - 4. Press 1 �
2, 3 � 4 or 5 �
6 to indicate which of the three personal entry code positions you wish to
use. - 5. The doors will again lock then
unlock to confirm that your personal key code has been programmed to the
module.
Tips:
- Do not set a code that uses five
of the same number. - Do not use five numbers in
sequential order. - The factory set code will work
even if you have set your own personal code. - If you program a code to a
position that already contains a set code, the previously-set code will be
erased.
- 1. Enter the factory set 5�digit
code. - 2. Within five seconds, press the
1 � 2 on the keypad and release. - 3. Press and hold the 1 �
2 for two seconds. This must be done within five seconds of completing
Step 2.
All personal codes are now erased and only the factory set 5�digit code will work.
Setting FOB to work with
your vehicle1. Sit in car, doors closed.
Electronically unlock all doors using the power door unlock switch on the
driver’s door.2. Insert key into ignition
switch and turn from OFF to ON 8 times within 10 seconds with the 8th time
ending in the ON position. (5 times on some models)3. The doors should lock and
unlock by themselves to signal programming mode.4. Using your remote: lock the
doors. -
I am also amazed how those pickups can haul some of those big 5th wheeled motorhomes. They just cruise by me like I am pulling doubles.
-
When a cosch is at a remote storage facility It’s a good practice to shut down all coach systems at the breaker panel except the battery chargers. If you have one house bank only one charger needs to be on. This practice does 2 things. First it’s the simplest way of ensuring non essential loads are off. It also reduces the possibility of appliance damage if your coach takes a power hit.
Some may elect to have an air conditioner or dehumidifier left on. Only the circuit breakers supporting should be left on.
When your coach is stored the inverters (not the chargers) need to be off. There is no reason to deplete house batteries due to an interuption in commercial power.
If your coach is stored in an open storage facility you might want to leave the generator autostart on. Never leave it on if the coach is stored indoors.
-
We stopped for a night and extended our stay because we enjoyed relaxing while watching the barges on the river. They have some nice sties and will easily accommodate your bus.
The advice regarding wet weather is correct. You don’t want to be there if there’s been, or about to be, significant rainfall.
Hope you get to check it out….
-
The easy question to answer is the air flows in the direction of the arrow so when it is installed the arrow should point to where the air is going (away from the compressor). I think if the check valve seat is a pliable material rather than relying on metal to metal it should work OK.
I don’t know if all DOT compression fittings have the internal tube. The fitting parts you showed could be perfectly fine. One key to success on compression fittings is to only tighten them according to the book for their respective size. Somewhere in the Prevost maintenance manual it lists the standards for tightening compression fittings. I just cannot remember where it was that I saw it.
The bottom drain should not require the removal of the screw. I suspect it has a hole in the center of it and when you loosen it air and water is purged through the center.
-
GOOD!
THANKS!
-
Rick,
Normally the blue wire is surge brake, but it’s not in the middle. The middle should be 12v for trailer interior lights or for charging the break away battery and hot all the time.

-
Jon, I am with you on that at least as far as my personal needs are. In winter of 2009 about a year after buying our bus, while in N Ohio at Christmas time, I bought a tank of Bio-Fuel, thinking it would be “good” to clean out my fuel system, as I had just undergone a filter change. Starting out of Toledo, Oh into Myrtle Beach, we had to change out 2 filters and before the trip from there into Fla then home to Arkansas, 2 more times. Each time a filter change did the job. At one fuel location that we limped into a fellow in an older motorhome came up to me and said he figured we were having trouble as he had never ever thought he would be able to pass a Prevost on the Interstate with his rig. No More Bio for us!
-
I would order from Prevost for an H mudflap. Like Jon said, they will be happy to look the correct one up for you with your VIN number.
-
Darrell…here you go…

-
Thank you, Jon. One of the pitfalls of having SOB is lack of a vibrant group of enthusiast owners. I do have quite a library of the MCI manuals, so I will dig in as you suggested. There are certainly some differences from Prevost. The MCI has several computers which monitor and adjust ride height. In fact, the operators manual suggests that if the bus is ever towed, the engine should be run at high idle during towing in order to power them, even if the tow truck is supplying air to the systems. The kneeling feature is still intact on mine and MCI also has controlls that allow increasing and decreasing ride height by several inches while moving slowly to clear steep driveway aprons and low clearances. I like your idea of super-sizing the the pneumatic drawings.
Regarding the Jun-Air compressor, my documentation shows that the converter installed a Model 6, probably the motor only version since it was plumbed directly into the aux tank. Is that what you Prevost guys have? Is there any reason for the compressor to have its own tank? The Model 6 has max pressure of 120 psi, so the tank would have to be pretty big to make it useful for filling the tires, I think. They are very pricey. If anyone has a line on a used one I would be much obliged.
-
Jerry, you may have an equalizer on your chassis bank, I do. Not all chassis power requirements are 24V on my coach. Unless you have a 24V house bank, you will not have an equalizer on your house bank.
-
Note to Big Al,
I think you are poking fun at my flip phone, but I never get pop up ads on my phone. That might in part be attributed to the fact the phone is rarely turned on. By not turning it on I never get those pesky sales calls.