Forum Replies Created

Page 52 of 76
  • Jim/Chris

    Member
    April 24, 2015 at 4:28 pm in reply to: Tire Date Codes

    i found some dated 47th week of 2014. I am trying to hold out for 2015. What are you finding?

  • Jim/Chris

    Member
    April 23, 2015 at 8:31 am in reply to: 13 great months and rolling on!!!

    Andy..I think Peter is going to buy Tom’s H and Tom will get a slide coach this time. You know, for Nancy.

  • Jim/Chris

    Member
    April 19, 2015 at 8:54 am in reply to: Not shifting

    Rick,

    I
    would think your vintage bus would already have Transynd, 50K is the
    usual change interval. There’s no other sensor that I’m aware of, but
    be sure to have someone such as Prevost or DD do the tranny, over
    tightened filter bolts will cause some serious problems. They need to
    follow the torque specs to the letter.

  • Jim/Chris

    Member
    April 9, 2015 at 12:53 pm in reply to: Overnite

    Gary,

    Did you click on the PC Map?

  • Jim/Chris

    Member
    March 16, 2015 at 11:47 am in reply to: Using Jake Brake / Exhaust Brake

    The Jake brake activates when the pressure is completely off the pedal. If you want to decelerate, even when it’s on (all the time for me), just keep a very little pressure on the pedal and it will remain off. At least, that’s the way it’s supposed to work.

  • Jim/Chris

    Member
    March 11, 2015 at 1:28 am in reply to: Outstanding Customer Service

    Sid, yes, we are in 368. Only here for a quickie but, will try to catch you Wensday.

    Thanks for all the comments on the new bus to all that posted.

  • Jim/Chris

    Member
    March 1, 2015 at 5:50 am in reply to: Hub leak?

    Joe’s wheels look that way because he has stud piloted wheels. So they are fine. That’s the good news.

    Yes his hub seal is leaking. Yes he can pull the axle, remove the 4 1/2″ nut and pull the entire hub without removing a wheel, but to do that he is pulling the dual wheels, brake drum, and hub all at once. If he has one of those hydraulic wheel carriers it can be done that way, but the danger is damaging the seal trying to slide that entire assembly back in place.

    So Joe, fear not. You have a choice. You can drive XX hours (or minutes) to a competent shop, pay for the 2 hours it will take to replace the seal and drive XX hours home, or you can do the job yourself.

    You need to take the wheels off yourself. To do that you can buy an X12 torque multiplier for over $700, or you can buy a 1″ impact wrench if you have a big enough compressor and air line. You can get one as low as $200, likely $400 to $500.

    You need a socket and 3/4″ drive for the center hub nut. Then the job just involves pulling the brake drum (the countersunk screws sometimes are a pain to remove, and then the hub, or leave the drum on the hub and fight with 200 pounds of iron.

    The seal can get pried out, and the new seal can be inserted using a tool specifically for that purpose or you can carefully tap it in place using a short section of 2X8 and a hammer and a little patience.

    It is not a difficult job in the sense it is highly complex. It is a dirty job, you need to be creative to be able to move the heavy parts around (I use a common floor jack so I don’t have to lift the brake drum) and it just requires a degree of care. In addition to the hub seal you need a ten hole gasket for the axle flange and a willingness to get dirty cleaning things up real well so you keep the hub seal clean and have clean bearings to inspect..

    BTW, if your differential is full you can drive a considerable distance as in hundreds of miles with no concern about if the bearings are getting lubed. If that was a big leak making driving impossible you would have oil all over the place.

    I have no hesitation encouraging you in doing the seal replacement because if you can get it apart, you can get it back together. And you will learn a whole lot about your brakes, how they work and will see first hand their condition. You will likely have to clean the brakes and drum real well because from the looks the oil has gotten on the shoes and in the drum effectively eliminating braking from that position.

    I’m curious because I am finding a pattern to hub seal leaks. Is it on the passenger side?

  • Jim/Chris

    Member
    February 27, 2015 at 10:18 pm in reply to: Oyster Fest 2015 – A No Rally, Rally

    I wanted to poke some fun at CC owners because I worked on a few of
    them, but then I remembered how shabby some of my Angola wiring was
    done. I think, maybe mine was their first one, their practice run. So in
    a public forum that will could live forever in cyberspace I’m not gonna
    say much. When we’re all setting around my ladders, camp fire or
    clothes line and sipping on our favorite drinks I’ve been known to exaggerate any perceived flaw.
    That includes mine too.

    Ken

  • Jim/Chris

    Member
    February 17, 2015 at 10:57 pm in reply to: Coolant Filter Valves

    Jerry close the valve half way and tighten up the packing nut then re open the valve

  • Jim/Chris

    Member
    February 16, 2015 at 7:39 pm in reply to: Valve Stem Position

    On one of my buses, the stem support was made from very stiff rubber/plastic like material and I doubt the stem could flex at all. I just hate the extensions, but some appear better than the rubber ones.

  • Jim/Chris

    Member
    February 16, 2015 at 5:00 pm in reply to: Prevost Warranty Service

    I don’t understand why a corporate operation seems to consistently get their billing wrong (and always over by all accounts) Makes you wonder a) how often they do get away with it and b) who is driving this type of behaviour behind the scenes? Seems to be happening too often to be coincidence or someone having an off day. Especially when they are charging top dollar hourly rates in the first place. How many of you guys run your businesses like that?

    As was discussed on a thread previously about trusted independents vs manufacturer, it will be those who get the “whole package” right who will get my business (in time)

    Thanks Mark for raising the issue.

  • Jim/Chris

    Member
    February 16, 2015 at 1:37 pm in reply to: Prevost Warranty Service

    M

    You need to talk with the Service Manager and the Billing Manager. Talking to the Tech is a waste of time. The more to go to their shops you soon learn what tech is the go to guy for questions and service they are also the go to guys for the other tech. You don’t know if you are getting a 15 year veteran or the resent hire to work on your coach. I think PSC would be the only place you could get warranty service work for no charge. I live 2 miles from a Volvo Service Center (over the road trucks) but when a was trying to get my recalled brake lines replaced, they wouldn’t touch them, no experience on buses.

    On questions if you ask the tech a question while he is working on your bus and he stops to answer it most likely it will be included in the time it took to replace or work on whatever he was doing. Long answers should be directed to someone standing around or the service writer. Remember just be cause he is a service writer or manager he may not know what he is talking about, they are not all techs who moved up the ladder. I was told once by my service writer who I knew for 10 years that the reason the Turbo in my Excursion needed to be replaced was because I towed it behind my Bus which kick up to much dirt. So I asked around some of these guys are hired into those positions.

    Do what was said, be up front with them and contact them now about your last service and billing. I am sure they will correct both for you. I have never had a problem with them reducing their bill when I pointed something out that was done or was over charged. You just have to talk to them.

    Greg

  • Jim/Chris

    Member
    February 10, 2015 at 7:43 am in reply to: DO YOU KNOW

    Clues?

  • Jim/Chris

    Member
    February 9, 2015 at 2:23 pm in reply to: Mirror Question

    In that context we clearly agree. I need to see at least a minute amount of the side of the bus as a reference when backing up. It is difficult to gauge your position relative to the next lane or a car in the next lane without having some reference point on the bus.

    And I don’t know if others need that reference point, but I need it to know my placement relative to something else fore and aft. I judge where my fuel tank fill point is relative to the hose on the pump by being able to see the closest side marker light to the fuel door and the fuel hose at the same time so I can line them up.

  • Jim/Chris

    Member
    February 3, 2015 at 12:11 am in reply to: Battery Issues

    Mark: One battery had expanded and the other battery was OK? What kind of batteries are those (make and type of construction)?

    Maybe a knowledgeable battery person will chime in and give us some insight into what might have caused the battery to expand like that.

Page 52 of 76