Forum Replies Created

Page 45 of 76
  • Jim/Chris

    Member
    April 30, 2016 at 7:40 am in reply to: WiFi

    Well, as of December of this year 2G is gone. It is called sunset of 2G I think. It goes away. A lot of alram systems have to be upgraded to 3G or beyond. We a re upating ours, this is how I became aware of this.

  • Jim/Chris

    Member
    April 23, 2016 at 9:16 am in reply to: 2 year old house batteries expected usage?

    So trying to understand based on my panel what I have.

    I know it’s a 12v system, so DC Volts (on my heart interface panels) reads 14 when on shore/generator.

    The DC Amps reads what I am guessing is he draw on the system.

    I do know that as soon as I turn off the Generator, the DC Volts drops to about 13. The DC Amps vary depending on the draw. I am seeing with pretty much basic things on (refer and what ever is there that we have no control over) I see DC amps at between 20 and 30.

    I have one switch panel that runs on the inverters (handles refer, micro, outlets, water pump, air compressor). By the morning, I will see this panel will be “dead” by the morning and the heart interface panel will be showning DC Volts at 10 and flashing. THis is even with autostart set and the generator hasn’t started yet. These are lifeline 8D batteries I bought about two years ago and these live about 99% of their life on shore/driving with very litle time on generator overall.

    I think last night I ran the generator for a good while to get the batteries charged. Let it off around 7:30 PM and by 5:00 AM it was dead on panel 1 and the Heart Interface panel was blinking at 10 DC Volts. Not sure if this is expected or if I should be seeing better time on the iverters with very little running.

  • Jim/Chris

    Member
    April 22, 2016 at 9:02 am in reply to: Holding Tanks wake up

    Anybody know what Vantare tanks are made of?

  • Jim/Chris

    Member
    April 16, 2016 at 9:26 am in reply to: The Law regarding Prevost Coach operation in TN

    Between the entrance door and front slide, just to the left of the entrance LED light, we have a plaque that says ‘Private Coach’ (on both sides). …….. and if the cop gives me any lip, I’ll flip on my blue under carriage lights and turn on my siren! I’ll show’m!…… as I’m escorted to the back seat of their ‘company’ car. LOL!

    Mark

  • Jim/Chris

    Member
    April 13, 2016 at 8:26 pm in reply to: Dometic penguin condensation leak

    Have you checked the drain hoses for blockages? I would look there first.

  • Jim/Chris

    Member
    March 21, 2016 at 7:06 am in reply to: fried inverter

    Joe Carter figured out what happened. He says all electrical wires and components have smoke inside them. I think what happened was the smoke escaped.

  • Jim/Chris

    Member
    March 16, 2016 at 10:25 am in reply to: What wheel bearing oil in the hubs?

    I recently replaced all my hubcaps (only because someone had painted over the plastic “windows”). I like to check my hub oil during pretrip inspection so I can detect any leaks quickly. Pulling the plug to check the oil was a pain. I used Lucus hub oil. I don’t remember the viscosity. Got it at the local Freightliner dealer. All the other advice is spot on.

    Similar vintage! Mine is an ’82.

  • Jim/Chris

    Member
    March 10, 2016 at 2:12 pm in reply to: Magnum Changeover and Watchdog Autostart

    Talked to Troy as suggested and he was no help. Said that he does not know how to do it. Also said that they change over the old Heart ot Magnum but leave the Watchdog alone. Apparently Watchdog modules are still being repaired as needed on all vintage coaches. No adjustment to the voltage to trigger autostart and no temperature trigger.

    I refuse to believe that there is no way to wire in parallel a Magnum AGS and be able to use buttons inside, set voltage trigger and temperature trigger. Jeff is smart and good with this type of stuff…. He has done it I believe….Jeff can you help ? I’ll pay for the diagram.

  • Jim/Chris

    Member
    March 8, 2016 at 1:39 pm in reply to: Planning Ahead

    That was our very own Bill and I’m sure he’ll jump in here.

  • Jim/Chris

    Member
    March 5, 2016 at 7:39 am in reply to: Analog to Digital TV

    Looks really good Tim, I wouldn’t even worry about trying to solve the audio problem, the sound bar looks nice the way you mounted it.

  • Jim/Chris

    Member
    March 4, 2016 at 12:03 pm in reply to: Know who has Marathon coach #0678?

    Did Mark sell it ?

  • Jim/Chris

    Member
    February 29, 2016 at 8:36 am in reply to: Brake chamber replacement

    http://www.rangerbrake.net/homepage/RB2015.pdf. Try Ranger Brake-Tennessee

    Try Fleetpride and here in Indio California

  • Jim/Chris

    Member
    February 28, 2016 at 6:20 am in reply to: What is the brakes fail?

    I am not aware of any Prevost coaches that do not have spring brakes for parking or emergency. There might be some older vintage coaches, but of those listed in signature lines I don’t think the dump truck scenario would be what happens.

    First it has to be understood that while air pressure is required for our service brakes to function, air pressure is also required to release our parking or spring brakes.

    If there is a catastrophic and sudden loss of air pressure the emergency or parking brakes are going to automatically apply when the loss of air pressure drops our systems below abouty 45 PSI. On older coaches with a spring brake on the drive axle only the stopping force will be less than that on later coaches with spring brakes on the tag and drive axles, but unless the springs have broken all coaches with loss of air are going to stop.

    One reason we stress every one should perform the pre trip brake test is to verify the parking brakes will automatically deploy as air pressure diminishes. If you have any question as to the condition of the springs in the parking brake put the coach in drive and see of the brakes hold or apply the parking brake at a very low speed to verify the coach will stop.

    My 40 foot 1987 coach had a spring brake on the drive axle only. Spring brake meaning when the parking brake (emergency brake) was applied only the drive wheels were braked and that was by the large spring that is normally retracted when the brake is released. That parking brake was sufficient to hold my coach stopped on my driveway. But only barely. When a spring broke on one side my coach would no longer hold in the stopped position so I knew the brakes had an issue and I replaced the brake chambers. That is not part of the DOT pre trip brake inspection, but it was a clear indication my emergency braking would be compromised. The point is we as drivers have to be fully aware at all times of our coach and its systems because if we allow enough to go wrong and we defer maintenance we can end up like the dump truck. But if we do we have no one to blame but ourselves.

    In our seminars and on this forum it may appear we are beating this DOT brake test requirement to death, but it is the only way you have to insure your bus is not in a video showing what happens when brakes cease to function. BTW long before your coach gets to the point where you have zero braking there are going to be so many clues such as lights and buzzers going off it is hard for anyone to reach the point where the coach is free wheeling.

  • Jim/Chris

    Member
    February 20, 2016 at 10:58 am in reply to: New Bus….Happy Ending!

    Congradulations on your new bus… Looks Awesome!! know you’ll love it. Hope 2 c u down the road.

  • Jim/Chris

    Member
    February 7, 2016 at 1:25 pm in reply to: Level Low Issue

    I’m not sure I follow your description of how air is exhausted from the front air bags.

    The only air that should ever escape through the 5 port solenoid valve manifold is the Norgren valve pilot air. When the solenoid valve on the manifold opens it is sending signal air to the actuator on the end of a Norgren valve. If the solenoid valve closes the actuator will not return to the normal position unless the pressurized air to the actuator is exhausted and that is the air heard coming back through to 5 port manifold solenoid valve.

    I believe the air for all three positions on an unaltered Level Low system exhausts from the air bags out the 3 port valve on the steer compartment bulk head. With a Liberty modified system air from the rear is exhausted from solenoid actuated 3 port valves in the front bottom of the steer compartment.

    Unless the center solenoid valve is actuated the ride height valves should have no impact on the coach. When the center solenoid valve is energized it shifts the control valves to open a path for air through the ride height valves. In every other setting other than the road or driving position the ride height valves will not function. If they are something is very wrong.

Page 45 of 76