Forum Replies Created

Page 24 of 76
  • Jim/Chris

    Member
    March 31, 2019 at 2:00 pm in reply to: Valve Stem Position

    Tom.

    I apologize for my ignorance here, but in your comment with the top picture you say “I position mine to rotate in the direction of the wheel.” Are we looking at the driver side or passenger side in the picture? I installed the fx system, and I want to make sure I have everything pointing and going the right direction. Just for the record my guess is passenger, and I’m betting red at the casino later.

    Thank you,

    Dave

  • Jim/Chris

    Member
    March 31, 2019 at 1:59 pm in reply to: shoutout – Incredible Bank

    Jon

    thats what I don’t get. We have a stellar record. If the “excess cash” prerequisite is ability to pay off bus note at anytime, why would we try for a loan. We weren’t given any perimeters for “excess cash standard”. Just given that reason for rejection

  • Jim/Chris

    Member
    March 31, 2019 at 7:50 am in reply to: How comfortable are no slides?

    One path I avoid traveling is to compare slide options unless I have taken a lot of time studying options and possibly have experience with those options. Before I had a 2 slide coach I was like a lot of others and could not see how slides can be justified because both my non-slide coaches were very easy to live in.

    In fact both had features I lost when we bought our existing two slide coach. My previous 45 foot non-slide coach had an abundance of storage space compared to the slide coach and it wasn’t fully realized until I tried to move our stuff from that non-slide coach into the current coach. I had a lot of stuff we used to carry that I could not fit. The largest disappointment was the reduced height of the bay due to the slide reinforcement prevented me from getting our two bicycles in the bay.

    Having said that, there is still no way we would go back to a non-slide coach. The way we use our coach now is completely different than how we used previous coaches. When we travel now we tend to go somewhere and stay a while. We are not doing trade shows so we do not need a lot of space for storage in a bay. Having the extra floor space provided by the slides has a real value and makes the use of the coach much easier and more enjoyable. Even if we are just going to stay overnight somewhere we still run the slides out, something that takes just a couple of minutes. The only thing I have to do relating to slides other than pushing the buttons is to roll up an area rug used on the living room floor. So use of the slides is easy and doesn’t require more than a few minutes to put them in or out.

    But the biggest deal about the decision regarding slides or no slides is if they make sense regarding how you use a coach.

  • Jim/Chris

    Member
    March 29, 2019 at 9:35 pm in reply to: Mini Rally

    Still have my reservation from last month. Beautiful area

  • Jim/Chris

    Member
    March 26, 2019 at 5:46 pm in reply to: Advice/Strategy

    I am late to this discussion, but my 2cents.

    I sold a 2009 Monaco Executive 4 slide outs,last year to get out before it turned

    10 years old, and lost even more$. and bought my 2000 Marathon XL non slide

    I don’t agree with some of the depreciation rates forecast for the 2000.

    Looking at Prevost for 4 years and I don’t see older coaches for half what I have in mine. so glad I pulled the trigger now;)

  • Jim/Chris

    Member
    March 26, 2019 at 12:54 pm in reply to: Michelin Tire Pressure Chart

    So Jon:

    Can you tell us what pressures you are running on each, front, drive and tags? Lots of opinions here on what to run as just need to find a common ground to assure optimum pressures.

    As you know us XLII’s are limited on bay space so can’t carry all the extras that an H can carry so we should all be close to the same given like kind converters, water, fuel and dump tank capacities.

    Tks,

  • Jim/Chris

    Member
    March 18, 2019 at 8:41 pm in reply to: Squeaks and rattles

    I put pipe insulation foam on my front windshield window shades and toll booth shades to keep them from rattling.

  • Jim/Chris

    Member
    March 16, 2019 at 7:16 pm in reply to: Is it true?

    None of what anyone has said has mentioned the tail lights, which was part of the original question. The answer to the original question is still NO.

  • Jim/Chris

    Member
    March 11, 2019 at 11:41 pm in reply to: XLII Buyers Beware

    I believe it is. We tapped around a2016 X-3 two years ago and found loose seams.

  • Jim/Chris

    Member
    March 11, 2019 at 8:21 pm in reply to: Depreciation curve

    Thanks…that issue about the class A trade in is one i was worrying about

    What about initial discount off new list, as starting point?

  • Jim/Chris

    Member
    March 8, 2019 at 8:08 am in reply to: Stuck and not sure what to do

    I dug way back in the airbag archives and this era was discussing air bags for a 1991 XL. Back then Prevost was mistakenly reversing the 259 and 260 bags in the parts department and a bunch of coaches got the wrong bag.

    126 – May West

    259 – Motorhome

    151 – Entertainer

    260 – Seated Coach – double flanged

    This was a post from Jon.

    Lets assume the 259 is indeed a direct replacement for the 126. Assuming their diameter and height dimensions are identical they should lift the front end of the bus easily. Using the 11″ diameter as the effective lifting area the air bags have a 95 square inch lifting surface. The lifting surface area determines how capable an air bag is at raising or supporting the weight placed upon it. In the case of the 259 and 126 this translates into an ability to support 9500 pounds per air bag at 100 PSI. This is theoretical because we do not know the actual lifting area, but is good for analysis.

    The entertainer air bag 630151 has a 12 inch diameter. That additional 1″ of diameter does not seem like a lot, but it calculates to 113″ of lifting surface, or one that is capable of supporting 11,300 pounds at 100 PSI.

    Stated another way, the 259 requires 73 PSI to support my coaches front end weight and the 151 requires 62 PSI to accomplish the same thing.

  • Jim/Chris

    Member
    March 7, 2019 at 7:14 pm in reply to: First Post

    Is there any seminars on the west coast ?

  • Jim/Chris

    Member
    March 1, 2019 at 11:01 am in reply to: XLII Buyers Beware

    Yes Jon, you’re correct. Only Prevost can determine extent of “delam”. In the case of the coach we looked at, the on hands “tapping” gave us knowledge. I checked with Prevost, and got the worst case scenario of every panel being replaced. $40K. It may be much, we were preparing for the worst with our offer. The only way to know the extent of delamination is to drive the bus to Mira Loma. That’s a 620 mile round trip.

  • Jim/Chris

    Member
    March 1, 2019 at 9:40 am in reply to: Delamination

    I’m certain Prevost engineers did a lot of research, not only independently but with suppliers of adhesives and tapes. The H3 used bonded construction since it was introduced in the early 90’s.

    The problem with the XLII motorhome conversions was not apparently experienced on entertainer coaches or seated coaches because the motorhome shell is the only one with stainless panels from below the windows to the top of the bays.

    We Monday morning quarterbacks can easily say tapes (as an example) would have been a better choice, but unless and until we go through the testing and in the field use we are speculating. Should Prevost have done a better job? Yes, as a Monday morning quarterback it is easy for me to say that. But as a former manufacturer I can say with conviction that on very limited production runs as our chassis are, panels will be fit by hand and in the case of some adhesives you never get a second chance if the panel is slightly mis-oriented. I would want an adhesive that allows some slight movement and adjustment of the panel location while it is being applied.

    It was said previously that some adhesives are so strong that a panel gets destroyed if it has to be removed. From a production point of view that would require some very precise panel positioning and the tooling cost on the low volume of motorhome shells would be prohibitive.

    The composite skins on the XLII entertainer shells and seated coach shells as well as the H3 are far less likely to separate. Could it be the coefficient of expansion is closer to that of the frame structure? Our coaches going from a cold start in the morning, to a high temp as the day wears on causes growth of the chassis by as much as 1/2″. Do the stainless steel skins grow at a different rate of expansion, or is it the constant stresses on the bond as a result of the expansion and contraction cause failure of the adhesion?

    Is it a production issue in that after the adhesive is applied to the frame the panels have to be in place within a few minutes or seconds? When repairs are made is there evidence to suggest the adhesive failure is between the frame and adhesive or between the panel and adhesive or is it both?

    One thing is certain. Prevost has spent a fortune in customer support to make it right when the problem became known and I would bet anything that they had the best experts in the adhesive industry working on this problem. I find it hard to second guess them, even knowing it should not have happened to begin with. Sometimes shit happens.

  • Jim/Chris

    Member
    February 28, 2019 at 2:02 pm in reply to: Delamination

    What George suggested is a good start, but never ever buy a XLII coach without having Prevost test for delamination and provide an estimate of costs if repairs are needed.

    Delam repairs can be very expensive and you can be certain you will always know less about a coach than the seller. Do not put yourself in the position of thinking the coach is OK, only to find out after the purchase you need skin repairs.

Page 24 of 76