Jim/Chris
Forum Replies Created
-
I found no moisture damage in any of the Norgren valves I took apart. My front measures well below the weight max on the fronts as well. I also found using high idle worked to more quickly reach 80 psi, but went from 80 to 120 too fast to allow the front to reach max height. For me, the switch to using low idle and periodically pressing the brake to stay in the compressor on zone longer did allow the front end to go to max height.
i only replaced some of the five Norgrens in the steer compartment, so still might have moisture damaged units elsewhere. And, we have only owned the coach for three years so I have no idea which air bags might be on the coach.
Jerry
-
Ride height changes dramatically effect alignment, especially on vehicles where both the front and the rear ride height are adjustable. Adjusting one end effects the other end so it is not a simple twist and go operation. There is enough hysteresis in the suspension that the coach needs to be driven (or exercised as Jon indicates) to get it to settle into where it is going to be going down the road before re-measuring ride height once it has been changed at one end or the other. Only when ride height is correct can alignment be performed.
In the front wheel drive GMC motorhome community this is especially a problem. There, the rear ride height is determined by air pressure in the bags much like our Prevost, and the front ride height is adjusted by twisting torsion bars. With those coaches if the rear ride height is off, the front will be very hard to get right due to the weight transfer that takes place.
I built alignment kits for that community because I found that even experienced alignment shops would routinely drive a GMC onto their alignment rack, take an alignment reading and then jack up the front end to make it easier to reach the alignment cams which were located on the upper a arms. They would let the coach back down and then use a chain or bar to jiggle the front end and re-measure the alignment. Satisfied, they would punch the button to print out what they felt was the perfect alignment specs and drive the coach off the rack. The unsuspecting customer would drive the coach home only to discover that the front end settled down on the way altering caster, camber and toe in the process.
To get it done right the owner had to get ride height correct front and rear, which required blocking the coach at proper rear ride height, then setting front ride height to spec, then driving the coach two to ten miles and checking it again until it was correct after that drive. Then they could either go to an alignment shop, or use one of my kits to set the alignment insisting that the tech NOT jack up the front end in the process.
I doubt if our front and rear air bag suspensions are quite as touchy, but likely some of the same forces and hysteresis are at play.
The other exacerbater with GMC motorhomes is the spec on ride height is +- 1/4″ while the spec on the ride height controller is +- 3/8″. Go figure!
Jerry
-
Maybe…
If you think that you could take to measurements and draw it in a simple cad program…maybe this could help.
Just throwing out another idea.
-
Tom, this is great since are options in Denver have dwindled
-
Probly only needs o ring
-
Thank you Tom, would definitely appreciate that.
-
I use this:
SharkBite 1/4-in To 1-in-in Pex Cutter Pipe Cutter
About $12. Multiple variations, all do the job well.
-
Swapped out the hose with the assistance of Bob Meurer. Part # 513469 for $39.79. Could only put one hose clamp on left side as not enough room for second clamp as it would have pinched the new hose right at the pipe connection. I believe the original dual clamp pinched the original blue hose and caused it to rip right at the pipe connection.
-
There is a difference in these. You get what you pay for. In a pinch a pack from an auto parts store will work, but a good tire shop will have better ones.
-
Jim/Chris
MemberOctober 14, 2019 at 9:29 am in reply to: Series 60 Engine ignition off at highway speedI had the same problem, except not just on a hill. The engine would stop and then it might start up right away or take lots of time.
My problem turned out to be the switch in the back for rear start. It would open and kill the engine. Took a while to find, but a new switch fixed the problem.
Did you try running with the switch in the rear start ?
-
Very nice, Jim! Successful DIY projects are great!
-
I never went anywhere. I just don’t post much, as I have little to contribute.
Actually, I admit that I was intrigued by the various opinions about over-revving a Series 60, the argument about the maximum recommended RPM, and all the associated testy comments and exchanges that accompanied the discussion. I was almost to the point of being unable to resist posting on that thread, but Jon, in an administrative stroke of genius, locked the thread, ending the discussion.
So, I went down to the bus barn, kicked one of my dogs, cranked up the bus, and over-revved the engine. But only up to 2500 RPM.
-
See my earlier update. It does not need a re-coat. But as a precaution I want to keep on hand.
-
Hello,
I recently used Bus Kote which seals, but main reason for using it is for heat reduction in bus.
It is awesome