Forum Replies Created

Page 66 of 214
  • Dick

    Member
    September 7, 2019 at 8:57 pm in reply to: Zip Dee refresh

    Better to look good then to feel good 🙂

    Like the rafter fix. I’ve never been able to get the rafters put up with the pole. Always get out the stepstool.

    Called zip dee about the seam sewing. Some are sewn, some are “welded”. Customer service didn’t have much info on what “welding” meant and what it is.

    I have some clear coat issues I’m looking at getting addressed. Put that on the nice to have list over the need to have list. Of course my front cruise are started to act up this week. I think it maybe the solenoid, have. Spare, will.see about swapping it out and hopefully that fixes it. If so, clear coat, if not, newer coach with roof air 🙁 (I’m about done with a bad deployment of a subpar option).

  • Dick

    Member
    September 7, 2019 at 12:25 pm in reply to: Shock Asorbers

    The red are polyurethane and I am sure they do a good job when they are new. But unlike the black rubber ones when they start to fail they crack apart in pieces and the total failure from the start of cracking until there is nothing left can take place over a span of just a few hundred miles. You go from a quiet riding coach to one that has a loud banging and clanging noise quickly.

  • Dick

    Member
    September 6, 2019 at 6:56 pm in reply to: Shock Asorbers

    I suspect you are talking about the dog bone end bushings for the rear sway bar.

    Easy job, but instead of the red urethane bushings use the black rubber type which I think are the same as shock bushings.

  • Dick

    Member
    September 6, 2019 at 2:29 pm in reply to: Remove Hitch from ’96 XL

    Heat from a torch works good on rust too

  • Dick

    Member
    September 4, 2019 at 7:21 pm in reply to: Drivers Side Window Fogging

    The only objection i have to a single thickness glass is condensation.

    My toll windows are single thickness and they get covered when it is cold outside.

  • Dick

    Member
    September 4, 2019 at 6:39 pm in reply to: Trans West RV Frederick, CO

    I doubt it’s only CO, but when we were in CO Transwest told us the same thing. They would not send a mobile vehicle to replace our air bag and they would not replace our air bag on-site because we were over 10 years old. So stupid, but I suspect they have plenty of business without our “antiques”.

  • Dick

    Member
    September 4, 2019 at 4:53 pm in reply to: Drivers Side Window Fogging

    I had the fogging issue almost 30 years ago on our first coach and on the subsequent 2 coaches.

    I fixed the first one myself on my 87, opened it up, cleaned it, applied a seal around the entire perimeter, but only made light contact, heated the entire assembly using a heat gun, then pressed it together to complete the seal.

    As it cooled the air kind of had a reduced pressure and was relatively free of humidity. When it cooled and the sealer set, I ran another bead of sealer around the outer perimeter at the joint.

    Then I reset the glass in the opening using sikaflex. It did not fog again. I do not remember what sealer I used between the two panes of glass, except it was black and on a roll with paper between the coils.

    I did not fix the thermopane on the second coach, and the current coach is showing some condensation on one of the windows and I am not screwing with it. We can put men on the moon, we can create artificial intelligence, but we can’t seal two pieces of glass.

  • Dick

    Member
    September 4, 2019 at 12:44 pm in reply to: Best Camera systems

    I have thought about putting them under the mirrors but if not there just below the first windows on each side. Cable will need to be pulled but the connection distance is short to the back of the monitor.

    R

  • Dick

    Member
    September 4, 2019 at 11:22 am in reply to: Drivers Side Window Fogging

    Dick, Call James Stallings at Xtreme Paint & Graphics in Nacogdoches, TX. He is a Prevost approved painter that can perform any kind of work on your bus. He is well experienced in crash repair, cosmetic repair, skin replacement, delam repair and polishing, painting, etc.

    Prevost Dallas drives buses from Dallas to Nacogdoches for James to handle cosmetic repair and then picks them up to return to the owner at Dallas facility.

    He will share what can be done about your window and answer any questions about how it will be done.

    936/560-5888 will be answered normally by Kristin (daughter) or perhaps Jennifer (wife). They will get James for you. You will be very pleased with his work.

  • Dick

    Member
    September 4, 2019 at 9:33 am in reply to: pro driver info

    Terry if you want to call me I will go out to barn and walk you through it on phone if you want, I was clue less until I got the manual. Art (805) 712-9449 Here is a link to the manual.

    https://www.prevostcommunity.com/PDF/Detroit%20Diesel%20ProDriver%20User%20Manual%206SE701%20Rev%201195.pdf

  • Dick

    Member
    September 2, 2019 at 6:51 pm in reply to: Remove Hitch from ’96 XL

    Mike: You can’t get the draw bar out if the receiver? Rusted/corroded in?

  • Dick

    Member
    September 2, 2019 at 6:24 pm in reply to: Learning the hard way??

    Mark,

    When the engine is running, it is making power. When the Jake brake is used, it is absorbing power. Two totally different things. In one case it compresses air in the cylinder, then at TDC it injects fuel, which ignites in a controlled explosion (combustion), which forces the piston down with considerable force. This force creates stress on the piston, connecting rod, etc, and this force eventually drives the wheels.

    With the Jake on, you have the same compression, but as the compressed air is ejected at TDC, there is no downward force. As a matter of fact, the piston will pull a vacuum, since both valves are now closed, and you have an opposite force on the piston and related components compared to the power stroke.

  • Dick

    Member
    September 2, 2019 at 4:21 pm in reply to: Learning the hard way??

    This discussion was had here in June & July of 2018, use search words “Mountain Driving Question”.

    Here is my research from back then, for whatever it’s worth: Check out the *Notice* on p.36 of the following link for DDEC V series 60 engines.

    Operators manual p.36


    It states “When descending a hill with Cruise Control OFF, do not allow the engine to exceed 2,500 rpm under any conditions. Failure to observe this precaution can result in overspeeding and serious engine damage”

    A decal that is on my June 1995 built DDEC III series 60 states “Max RPM NL 2225”. Also, my engine is governed to 2225 rpm.

    I try to never let my rpm exceed 2100 rpm for any reason.

  • Dick

    Member
    September 1, 2019 at 12:57 pm in reply to: Level/ Low

    Just let us know what you find. Especially if my theory is wrong because one thing Tom and I want to control on PC is to insure nobody is mislead by lousy information.

    As we all gain and then share knowledge it makes owning these complex vehicles much more enjoyable.

  • Dick

    Member
    September 1, 2019 at 12:04 pm in reply to: Learning the hard way??

    Sorry for the the thread creep, but in light of the recent brake disintegration issues, I did some quick back of the envelope calculations:

    If we assume weight of 52000 pounds, elevation change of 4000 feet, 14% grade ( the grade is irrelevant to the potential energy, but will be used for other calculations later). The potential energy created when ascending this elevation difference or conversely dissipated when descending is 67,259,559 calories or 78,336 watt hours.

    To put it in English it is the amount of energy you would use (and the heat you would create) by running 78 1000 watt toaster ovens for an hour.

    Some further analysis show with our 14% grade 4000 feet of elevation change happens over 5.4 road miles. Lets assume 30 mph. This give 10.8 minutes to traverse the distance, which is about .18 hours. So we divide the 78 toaster ovens by .18 and we get 432 toaster ovens on high for 10.8 minutes. And we wonder why brakes get fried! Of course in our proper technique, we don’t dissipate all the energy using the brakes, but it is dramatic.

    As a sanity check to the above numbers I converted this energy dissipation rate (67,259,559 calories/648 seconds) =103795 calories per second. Converting this to horsepower, gives 583 horsepower. Which says for sure Olivia was not going up the grade (assuming same steepness and elevation change up vs. down) at an average 30 mph, even without a trailer.

    A lot of assumptions here and no adjustments for energy conversion efficiency, wind resistance, etc. etc. But directionally it makes sense. Forgive any significant figure issues, or other physics “stuff” I’m a doctor not a geek. I took the physics without calculus in school.

    Edited to add this chart I found online. It is from a post citing some MCI /Allison data. Shows Allison trans retarder can dissipate what looks to be about 800 hp. Link to the post, it is by a Foretravel owner and there are some remarks in there about Jake vs retarder and I express no view on validity of his opinions, but the chart appears to be an MCI document:

    http://beamalarm.com/Documents/transmission_retarder_operation.html

    Retarder - How does it work

Page 66 of 214