Forum Replies Created

Page 32 of 214
  • Dick

    Member
    January 17, 2021 at 11:44 am in reply to: Fuel splash back filling bus

    We had the same problem. We fixed ours with kit listed in the bottom post here.

    Go Here!

  • Dick

    Member
    January 15, 2021 at 11:14 pm in reply to: 12V Dimmer Module Bypass

    Converter??????/

  • Dick

    Member
    January 15, 2021 at 6:53 am in reply to: Coolant Temp gauge scale

    One thing XL and likely early H3 model gauges did not have is a gauge marking to either indicate safe upper limit (red line) or a safe range marking.

    On my 87 and 97 there were no indications and unless an owner actually knew what they should be be studying various sources of information the only way anyone would know something was going wrong would be via a dash panel light.

    One good project would be to put a dot of paint or maybe a small version of the dot of paper like from a three ring punch. The best protection however is for normal, correct indications to become locked in memory and then any deviations, no matter how small become something to monitor.

    My XLII does have gauge markings so at least Prevost realized the benefit of them.

  • Dick

    Member
    January 13, 2021 at 4:54 pm in reply to: Wind sensor
  • Dick

    Member
    January 11, 2021 at 2:36 pm in reply to: What year did Prevost start independent suspension

    I have no idea at what vin # it became available but I believe it was optional for a period of production.

  • Dick

    Member
    January 8, 2021 at 12:09 pm in reply to: Knee replacement?

    Art, I had both knees replaced at the same time in late 2016. I had met the protocol for doing both at once. It was very clearly explained to me what I would probably go through doing them together, but I made the decision to do it as I did not wish to go through the rehab process twice and one knee was as bad as the other. I fully agree that it is not for everyone but it worked for me. The first two weeks was a living hell but once I got past that and the rehab started kicking in it went very well. If you want more information about the process and what I went through, feel free to call me. George 941 779 50180

  • Dick

    Member
    January 7, 2021 at 12:26 pm in reply to: Vibration-Am I missing something?

    Chuck: who did the U-Joint work? Prevost? Call the shop and talk to the shop manager. Let us know what he or she says.

  • Dick

    Member
    January 7, 2021 at 6:49 am in reply to: Heating a bus

    At 60 chimney should have plenty of draft.

  • Dick

    Member
    January 6, 2021 at 8:59 am in reply to: Chemical winter additives to fuel

    Can we all agree if the bus is headed north in the winter it is going in the wrong direction?????

  • Dick

    Member
    January 5, 2021 at 8:36 am in reply to: Lubricant change

    Thank you all for your help

  • Dick

    Member
    January 4, 2021 at 4:28 pm in reply to: Air seat solenoid valve replacement

    That is the way to do it then. Simple, easily serviced and to wear a belt with your suspenders add a manual shut off valve to each valve for service and to be able to manually control the seat if a solenoid valve fails.

  • Dick

    Member
    January 3, 2021 at 8:11 pm in reply to: Vibration-Am I missing something?

    Dick:

    JoSam’s did use a dail indicator on the old set of tire, that’s how we found the out of round passengers tag. Guess I will have to do it again with the new set of 365s.

    JoSam also did a 3 axle alignment about 10 – 12 months ago and also adjusted the ride height before aligning.

    Chuck

  • Dick

    Member
    January 2, 2021 at 4:56 pm in reply to: Suspension Squeak and engine compressor question

    Thanks for the replies. Another 100 miles down the road today and the squeak is gone! Yeah! The mechanic did squirt some WD40 on the shock mount bushings so that either worked or the bushings got worked back in. This coach had been sitting at ETLC for many months and we had only made one other trip from TN to TX where we sat for another 2 months. We are in MI now and we will see what happens after a month or so of work here.

  • Dick

    Member
    January 2, 2021 at 10:04 am in reply to: Vibration-Am I missing something?

    Ask them when was the last time they calibrated the balancer.

  • Dick

    Member
    January 1, 2021 at 7:11 pm in reply to: Suspension Squeak and engine compressor question

    I’m guessing sway bar link bushings. I think they are also called dog bones. If they are new, I wouldn’t worry too much unless one of the smarter guys contradict me.

Page 32 of 214