Dick
Forum Replies Created
-
WOW is all I have to say
Just got off the phone with Michelin, after explaining that I went into their dealer with old tires and no vibration. Had new tires installed and now have BAD hop/vibration, and going into detail as to how their dealers want to just keep putting the tires on the balancing machine and adding or subtracting weights to try to fix my Hop/vibration instead of taking the time to use a runout gauge to determine what the problem really is. Michelin has told me again that their dealers have done what they normally do and that’s all they can do.
I again referred to a Michelin Company video on You-Tube that explains in detail as to how a runout gauge on a stand and marking the tire/rim can assist in determining vibration/hop issue. I asked to be sent to a Michelin authorized dealer that would take the time to put a runout gauge on the tire/rim and determine what is going on (my problem “the bus” or their problem “the tires”). Michelin said their shops have done everything within their scope of work to resolve the hop/vibration.
Michelin said I was welcome to take the bus back to JoSam and have them spend the time to find the issue, BUT Michelin may or may not reimburse for the work.
Wow, Wow, Wow. There is some customer service for you. They won’t even take the time to trouble shot their own tires at one of their own authorized dealers per Michelin’s own recommendation on the Michelin Company video.
Speech less
Chuck
-
Thanks Al, I should know better but forgot. I believe I am beginning to suffer from CRS.
The person I refer to is Pat and she has considerable knowledge and is very familiar with PC and has responded on this forum when the need arose.
I will repeat again that our tires are literally an engineering marvel. To get the best use and performance out of them requires the need to follow the best practices for their mounting, installation, and future maintenance. None of the requirements are difficult, none require any more time than doing things the wrong way, and when everything is done correctly we get the most for our buck.
The “bible” is the book linked to above. Michelin also has a larger, more detailed manual that runs to about 290 pages and it covers everything. Dealers who do things the right way, and follow the procedures are the folks we should use.
-
We had our Output Speed Sensor have a wiring issue last Saturday as we were on the road to Florida from Houston. Prevost couldn’t help but ended up referring us to Expert Transmission. Lewis came out and got us running again. He was terrific and the cost was very affordable.
Highly Recommend them.
We have a 2003 XLii Marathon
-
Installed a temporary valve and air hose to the louver and closed it for a 300 mile trip. It is bad and leaking air but not so bad that the louvers wouldn’t stay closed for my test drive.
Maybe I just want to believe it, but I think I had less air/wind noise on my entry door and the front drivers area seamed to stay cooler with the outside air temp being in the 80s when the louvers were closed.
Does anyone know where to purchase a new plunger/actuator?
Chuck
-
Harry: It can really vary depending on so many factors. How fast is it driven (59mph or 72mph)? Interstate out west? or in the east? Lots of two lane roads? Did the drivers let it idle quite a bit to run the OTR A/C when sitting?
I think if you used 40 to 50, you’ll be in good shape.
-
We all know the real reason he was in Parumph with that fancy Vette. I put aside the dues money in case of bail, but since it wasn’t needed, I had to buy something.
-
Thank you, Don, I always appreciate your expertise.
Fred
-
As a side note: Keep your fingers off the top of the bag when you remove the plug and the bag rises. Yes I did find that out the hard way.
Chuck
-
Greg wrote: “but some of it was my mistakes” Is there anyone on the Forum who can say they never made a mistake with their coach that cost them some money?
-
I’m starting to experience what has going on Davy on.
The locksmith’s comment about the lock internals wearing the key, makes sense to me.
-
Marshall: “they flushed the motor and lines several times and ran the coach in between to get better extraction.”
What do they use to “flush the motor and lines”? Tap water? City or well water? Soft water?
I suppose some residual water is left in the system when they are done flushing. Correct?
And that get mixed with the new antifreeze when they put that into they system. Correct?
-
Dick
MemberMarch 12, 2021 at 2:27 pm in reply to: California Looking To Restrict Out-Of-State DieselWouldn’t doubt it, I mean look at there governor.
-
I’m not a antifreeze professional but this antifreeze I’m using is not the OAT technology antifreeze it is a conventional extended life antifreeze I think a 5 year antifreeze that they add the SCA protection in it that’s why the blank, I think after a while It would need a filter with chemical in it. I torture myself sometimes when i’mchanging something like antifreeze, and I like the input, when I first got bus I posted antifreeze question and Don and I spoke about antifreeze and this is what we came up with. The OAT has to be totally clean and flushed to change to, the Prestone not so much.
-
Is the shureflo just for flushing or is the flow enough for showering, washer, etc.