Archived
Forum Replies Created
-
Bonz,
Before I post a picture of the seat, the leather seating material didn’t get changed, just the foam. You still want a pic?
-
Way harsh, but I love it!
We are finally home from our globetrotting adventure. Had a great time! Now to get the bus ready to roll for the rest of the summer. Not much to do, just get it serviced and loaded up with our take along stuff and we are ready.
Jon: How is that new one working out? Still great I hope!
-
10 20s, or 20 10s, or 40 5s, etc. Next question.
-
Your gauges will tell the story. If your temperatures and oil pressure show good it is unlikely you have a problem with either of those..
There are only three reasons for a stop engine light. The two you can check on your dash will be high engine temperature, or low oil pressure. If they are good then the problem could be the coolant level sensor. I am not clear on conditions when the stop engine light comes on, but if it is at idle, does increasing the revs correct the problem? If so suspect an oil pressure sensor. That sensor is not reflected in your oil pressure dash gauge and can have an error even though your pressures are fine. If that does not cure it you can jumper between the two pins on the coolant level sensor plug and that takes the sensor out of the equation. If the problem goes away after that you have isolated the cause.
Before you go beyond that, flash the codes and see what they say. They will tell you why you are getting the stop engine light. Even if I thought I found the problem I would flash the codes to verify my findings or start by flashing the codes so I could zero in on the cause.
-
We know the shield is really still in the garage, so keep pretending it’s gone. Your a shield man at heart.
-
I’am feeling left out…no testing for us in Missouri ?
I’am sure you have heard the plastic shield has a new home in Missouri. Transportation was arranged for travel in a special design pick-up
.Missouri Highway patrol, Missouri DOT, Homeland Security, U. S. Marshals, and Cass County Sheriff, then tracked the movement to Springfield.
Yesterday was the official day of morning the departure from Peculiar MO. too Spingfield MO.
Show some support by sending cards with “cold cash” to help us through this diffucult time.
-
These LEDs are whole unit replacements for the halogens. I would really like to get rid of them for less heat production and less power draw.
-
Archived
MemberJune 9, 2012 at 6:14 am in reply to: Time to Change House Batteries – AGM/Wet cell – $The buss bar method provides two benefits. The first being it provides a more effective method of equally using and charging ALL batteries. Typically the connections between the charger/inverter and the battery bank are on the same battery of many in a battery bank. If this is done, the battery directly connected to the inverter/charger is used more and charged more than all other batteries. The battery the furthest down the ladder of connections is is used the least. To overcome this and still save costs, the positive connection to the battery bank from the inverter/charger is made to the battery at one end of the bank and the negative connection from the inverter/charger to the battery at the other end of the bank. This forces all batteries to participate equally in the charge and discharge process. The problem with this method is that a single weak battery or cell compromises the entire bank.
The other reason for using the buss bar approach is that it makes it simple to isolate a single weak or otherwise defective battery. Besides the one battery terminal with a temperature sensor, there is just a single cable connection to each battery, just another plus.
One note. The battery cables used between the batteries and the buss bar should be approximately equal length to ensure each battery discharges and charges equal to the other batteries.
Gil
-
Archived
MemberJune 8, 2012 at 11:52 pm in reply to: Time to Change House Batteries – AGM/Wet cell – $If you don’t mind, why did you intall a bus bar?
-
I will look tomorrow and let you know.
-
Archived
MemberJune 8, 2012 at 8:11 pm in reply to: Time to Change House Batteries – AGM/Wet cell – $I just went through a very similiar situation. My coach had 6 8D wet cells. I’m not a fan of wet cells in a confined space, so I changed to AGMs. I also had the wiring changed so that each battery is directly connected to a buss bar that is connected to the two inverter/chargers.
Best of luck,
Gil
-
Jon: Have you ever posted a how to on fan clutch replacement. I suppose it’s pretty straightforward; I see nothing in the maintenance manual.
I’ve been hearing a noise from that area while the engine is idling. This AM, I removed the drive beltand started spinning pulleys. Idler OK, fan OK, but I found the bad bearings when I spun the fan pulley. I’m assuming these are bearings internal to the fan clutch itself?
-
I’ll get them for you big boy…
-
When I made the switch over to LED’s I left the old Halogen’s in place. Mainly because I could see no market for them and about the only outlet to sell them would be on bus boards or Ebay/Craiglist. With LED’s currently taking over the market, I can’t see them selling quickly but it might be worth a try.
You never know what the other guy is looking for right?
BCO
-
Wondering, where did you install it in Your coach?
Here it is on youtube, Well I guess NOT I can not copy and paste into this Forum, that sucks!!!
JIM