Archived
Forum Replies Created
-
I just bought the lift chambers for my coach (Bendix type 36) for $86 each from NAPA. Prevost wanted $156 each.
-
Go with Jon’s recomendation. The Greenlee punchs will go through 16-18 gauge stainless steel and leave a quality finish. The bus is probrably 22 or 24 gauge. Sugest you go to a local electrical contractor and have them do it for you. The Greenlee punchs are on the pricy side for a single use. The larger ones will be pulled together by a hydralic ram that looks similar to an impact wrench rather than turning a bolt to squeeze the halves together.
-
I, like Jon, am in Knoxville, TN.
I did use the port side inlet, previously, but I now need 2 coax runs and it was very inelegant in my garage. I am well known for not doing things the easy way. I will often expend countless hours and dollars for incremental improvements in things… call it a character flaw!
It sounds like the Greenlee punch is the way to go. As sson as my new inlet arrives and is modified for two coaxes L’ii give it a go.
Thanks everyone!
-
Where are you located? I have a 100 amp plasma. Punch a hole with little or no cleanup and no discoloration or warping from heat.
-
All our coaches have a liftable tag. Trouble is nobody really knows if the tag is being lifted unless they actually get out to check.
-
Hi Dale,
Don’t know if you have the liftable tag or not but on my H3-40 that uses 1 more chamber on each side.
-
Just a couple of comments…………..we cannot assume because our coach has a specific part that someone else’s coach manufactured in a different year has the same part. If memory serves Jim’s coach has a combo brake for the tag so he has an emergency brake on both his drive and tag axles. Dale I believe has an emergency brake (a combo) only on his drive axle. Sizes vary on brake chambers from coach to coach and I shouldn’t have guessed what Dale’s were.
The price Jim posted for a #30 brake chamber is so high compared to what Dale will find when he shops prices, Dale is apt to think Fleet Pride is supplying the wrong part. A #30 is CHEAP. My guess if Dale posts it will be around $35.
-
Hey, those are cows not sheep… Do you guys in KS know the difference?
-
Rumor has it that the first person looking at Jon’s bus brought it.
Congradulations to Jon, this has a lot to say about bus care and record keeping. Jon keeps suggesting to us.
I’am sure the new owner will have many trouble free miles thanks to all the new parts in the bus.
-
It might be easier to make a longer coax cable to reach the existing plug.
JIM
-
I finished removing the drivers side brake chambers today.
The steer is #24 the driver is a #3036 or #36 ? there is no ID on the tag one. I’ll call Prevost Parts tomorrow and see what the availibility and price is and check at Fleet Pride, I’ll post the results.
-
Scott,
Don’t take this the wrong way, but if you changed out the thermostat, it could be in backwards. I’m also assuming the water pump is trying to do it’s job.
-
They are bonded as Gil says.
-
John,
The chrome in stainless makes it hard to drill and in my opinion the quality and hardness of typical hole saws is going to make it near impossible to do a decent job. If I were to need a big hole I would likely drill a center hole and use a Greenlee punch. Those are sheet metal hole makers that consist of a die and punch but you need to access both sides of the panel in which you want the hole.
The drilled hole is for the bolt that goes through the punch and die and as it is tightened the punch makes a clean cut through the stainless panel.
For a one shot deal I would not go out and buy one because they are a little pricey, but a phone call to shops that typically use them, such as an electrician, a plumber, etc. will turn up someone that has a set and likely your size.
If you cannot access both sides of the panel you can try a hole saw, but I suspect you will go through a number of them before you make the hole, even in material as thin as our bus skins.
-
Dale,
I would buy Double Coin again. I recently sold my 97, but they have done very well. I lost one a while back because I hit something that took a baseball sized chunk out of the tread and damaged the belts, but the others wore well and rode well. Michelin owns or controls Double Coin.