Forum Replies Created

Page 2228 of 2304
  • Archived

    Member
    June 20, 2012 at 5:50 pm in reply to: Another Jake Question

    On my XL and now my XLII there is about 1/2 to 1 inch clearance over the valve cover. There is a removable panel above the valve cover, but that is where cabinets or closets are in cross bed configurations. Removal of the panel can entail disassembling cabinetry, stripping carpeting that might be glued in place and all sorts of other gyrations to just get to the cover. Might be easier to pull the engine. (maybe)

    The engine cradle repair may in fact have helped or cured a problem if it was associated with the wiring going under the valve cover to the solenoids.

  • Archived

    Member
    June 20, 2012 at 5:02 pm in reply to: Charging House Batteries

    Dale, do you have a Delco 50DN alternator? A few us run Balmar 624’s to control the alternator current. I am running Deka AGM’s and I can adjust the voltage and profile for my dual Xantrex SW4024’s. I am upgrading to a 450 amp Niehoff C802. They were able to build me a custom regulator that would handle the high field current >20amps..

  • Archived

    Member
    June 20, 2012 at 4:54 pm in reply to: Another Jake Question

    I had mine of on my H3. Doesn’t the XL have 3 inches between the cover and the lower deck? The go no go factor is if you have the two piece valve cover. That helps.. You can take the upper cover off with relative ease. The high pressure boost pipe needs to be removed.

    FYI>> there is a new rebuild kit for the S60 Jake brakes.. It really does work well and worth the price of the $1280 kit.

  • Archived

    Member
    June 20, 2012 at 3:35 pm in reply to: Need a surge tank

    Oh yea that’s Luke. I’ll give him a call. I called Frankie Goodson here in North Carolina but he is on vacation till Monday. I am sure that one of them can find me something.

  • Archived

    Member
    June 20, 2012 at 2:28 pm in reply to: Another Jake Question

    You might want to pull the valve cover and inspect the wiring to the JAKE solinoid. You should have 3 connections under the valve cover. I rebuilt and updated my Jakes this past summer.

  • Archived

    Member
    June 20, 2012 at 12:43 pm in reply to: Need a surge tank

    Bus parts and services

    U.S. Coach & Equipment Sales, Inc.

  • Archived

    Member
    June 20, 2012 at 9:02 am in reply to: Need a surge tank

    Try Visone Auto Mart http://en.visonerv.com/cgi-bin/welcome.pl?

    Maybe Sam Caylor http://www.caylorsupply.com/ I think he has salvage Prevosts

    Ken

  • Archived

    Member
    June 20, 2012 at 6:17 am in reply to: COMPRESOR AUX

    Aux air on our coaches like a lot of other things varies with the conversion and how the owner uses the coach and wants it equipped.

    All of us use auxiliary air on the Prevost chassis in our suspensions. We don’t need aux air to keep the coach from leaning, but having aux air on some coaches will allow a degree of leveling without starting the engine. We also use aux air for belt tensioners, front door lock and the driver’s seat. Most use aux air for the small air bags under the generator and other uses for aux air (depending on vintage and converter) include the wipers, air horns, step well cover, pocket doors, bed lift, dump valves, forward shutters, transmission retarder and stabilizators. Coaches with slides need aux compressors because the inflatable slide seal keeps out moisture so aux air on slide coaches is not a luxury but a need.

    Some aux compressors are not capable of developing enough pressure to air up tires, but there are often enough air operated devices to justify having the aux compressor.

  • Archived

    Member
    June 20, 2012 at 1:12 am in reply to: Changing out break Chambers

    Tom,

    Like you, I don’t understand the price difference between your tag axle lifting chamber (640729) and mine (641425). Prevost Parts lists both as Type 36. The label on mine reads “MGM 1436018 C102297 641425.” Even though mine began life as an H3-45 seated coach with disk brakes on all wheels, I wouldn’t think that would make much difference. I would expect the tag lifting chambers to be about the same for all coaches. For a $600 difference in price for two, I’d check into it a little deeper. I can send a photo if you need one.

  • Archived

    Member
    June 19, 2012 at 10:56 pm in reply to: Direct to Dish

    OK… we live in East TX and had the same problem as far as local channels go they only offer one but we wanted them all ( out of Houston) so I changed our primary address to Galveston where we keep our boats and now we get all of the Locals CBC NBC ABC and a dozen others which is great for us. You can probably get the boxes in the bus and get a PO BOX or something then after that add the boxes to your house (by mail only & self install) and they will be programmed the same as the bus.

    Later on I changed our billing address the our office in Lufkin and have never had the first problem. Maybe you can figure something like that if you have an office address in your city.

  • Archived

    Member
    June 19, 2012 at 9:32 pm in reply to: Radiator in Vantare

    Bad news on the power. its 30 amps at 118 volts. You can run 2 ac units if you shut off the rest of the coach, Temp is in the mid 90s today.

  • Archived

    Member
    June 19, 2012 at 7:25 pm in reply to: New Steer Tires

    Lookin good Dale, you’re putting us to shame!

  • Archived

    Member
    June 19, 2012 at 5:46 pm in reply to: New Steer Tires

    While I wait for my brake chambers and tires to come in, I thought it would be a great time to clean and polish the wheels. Not a geat time, meaning fun, but a great time while the tires are off. I start with an acid wash and then use a polish, (Diamond Brite, thanks Roger), I like Blue Magic also. I use my big angle grinder with polishing wheels when needed.

  • Archived

    Member
    June 19, 2012 at 10:19 am in reply to: Changing out break Chambers

    Do any of you know if you have 3030’s on your drive? I have 3036’s. Fleet Pride said that 3030’s should work fine, I went ahead and ordered the 3036’s.

    I did learn that the first 30 of the 3036 is for the service braking and the the 36 is the size of the parking brake. So in summery, I have on my bus, steer braking; #24, drive braking; #30 and tag breaking; #16. Only the drive axle has parking brakes and they are #36.

    How does this configuration differ from the newer bus’s and 45’ers with more gvwr?

  • Archived

    Member
    June 19, 2012 at 8:01 am in reply to: Changing out break Chambers

    Ron,

    The lift chamber for the tag that I had to buy at Prevost was part #640729 and the price was 451.66. I don’t understand the big difference in price with what you mentioned. Could you verify the part number that Prevovst wanted 1560 please. If I paid too much and there is a different alternative, I would like to know.

Page 2228 of 2304