Forum Replies Created

Page 8 of 9
  • victor

    Member
    October 3, 2015 at 11:16 am in reply to: “BAL” Light troubleshoot

    glens: How did you determine it was a bad battery?

  • victor

    Member
    October 1, 2015 at 8:54 pm in reply to: Know Your Prevost Seminar 3

    Easter weekend? really

  • victor

    Member
    September 30, 2015 at 8:49 pm in reply to: Proactive vs Reactive

    Don I have redone two bus I agree with you they need care as they get older

  • victor

    Member
    September 29, 2015 at 6:02 am in reply to: michelin 365 tires

    Before we criticize Prevost for selecting the 365 tires, keep in mind we asked for it.

    Not specifically, but by wanting coaches bigger and better and with more features. My 40 footer was 41,000 pounds, the 97 was 46,000, and the current 2 slide coach is 53,000. The jump from the 40 to 45 shows the weight was almost proportional to the length. But the current 2006 has slides which add weight, plus a lot more heavier features. I have an 18,000# front axle which happens to be the limit for 315 tires. The X3 has a 19,000 pound axle and that exceeds the 315 weight limits.

    Then lets not forget the rush of owners who switched out their 315 tires for 365. My point is simple in that Prevost is responding to the market. For what it is worth in this month’s FMCA magazine a Foretravel is featured and it has 365 steer tires so Prevost owners are not in an exclusive group that should have a plan to deal with an unexpected failure of a tire. If any tire on our coaches fails we have a problem because neither 315 or 365 is sitting on the shelf in almost all instances.

  • victor

    Member
    September 26, 2015 at 11:20 pm in reply to: michelin 365 tires

    Call Dennis Orner Prevost Service Rep. 717-752-9305.

    I had a steer 365 blowout on the Ohio Turnpike 08/27/2015 he found me a 365 in Ohio, 1 of 2 a customer ordered but did not pick up. I was lucky up and running in about 4 hours. Possible Dennis might get one to you quicker than waiting a month

  • victor

    Member
    September 24, 2015 at 8:47 pm in reply to: Jeff is the Man

    Just pulling a leg. Of course, I do know who Jeff is. In fact, I have been at his place and will be there again starting on Oct 19 to have some stuff looked at, prior to the weekend seminar which we will attend as well.

  • victor

    Member
    September 24, 2015 at 4:11 pm in reply to: 2000 Marathon H3-45 MCD Display not working

    You should call Prevost to determine which MCD display they can currently get. The original one is probably no longer available. They were working on it last year when one of our service customers needed one because that backlight had go out. We were able to retro in an LED lamp to get him by and he has not expressed interest in going any further as long as the old display still functions, so I haven’t had reason to inquire with Prevost since on how it was going.

    They sent the customer one that had airbag warnings and all sorts of errors not applicable to a Prevost of that year, lol, so he sent it back.

  • victor

    Member
    September 22, 2015 at 9:19 pm in reply to: No turbo boost

    Where do u live at I might be able to help

  • victor

    Member
    September 14, 2015 at 9:58 pm in reply to: Behind the Gen Radiator-NOT GOOD

    Installed a new fan belt, NAPA #A39. The old one was probably the original.

    I’m don’t have to remove the fan and motor assembly to replace the sound/heat barrier material.

    Belt can be changed/adjusted by removing this panel in the inverter bay

    Below pic shows the belt tensioner

    I’ll start installing the new sound/heat barrier material soon. Pics to follow of course.

  • victor

    Member
    September 14, 2015 at 5:36 pm in reply to: led rope type lighting

    After reading Ben’s post ( http://prevostcommunity.com/forum/threaddetails.asp?Category=Electrical&ThreadID=2505 or see below), I am confident that I can just replace a few sections.

    These are 120v incandescent rope lights. They were originally all imported, and came in only 1/2″ or 3/8″ diameter. The individual bulbs are set up like “Christmas tree lights” in that for every section, the bulbs are wired in series. In this arrangement, if one bulb burns out, the entire section goes out. I can’t remember exactly how many feet were in each section, but they could only be cut at marked areas every 18″, with the extra stuffed back behind the cabinet or valance. When cut, there are lamp cord ends that have barbs on them to “stab” into the rope to hit the conductors that run to the bulbs. If you are so inclined, I would take one of the valances off so you could access behind it to the point where the lamp cord termination meets with the rubber-like light rope. If you pull them apart to expose the barbs, being EXTREMELY CAREFUL not to get shocked (120v AC power should be at the barbs).

    I have seen over time that either the barbs wiggle loose and no longer contact the wire in the end of the rope, or that one or more bulbs may be burned out, requiring you to replace the section of rope. At least this will get you access to replacing that section of rope, and let you verify whether or not you have power to that section. Since you have ANY of the rear rope lights working rules out a bad relay or the dimmer control. The only other connection points are 2 x 4 metal junction boxes buried at centralized “hub” locations in each side of the rear of the coach. If only two continuous sections of the rope lighting are not working, my bet is that it is the fault of the rope or the termination to that section of rope.

    Hope this helps.

    Ben Cummings
    Parliament Motor Coach

  • victor

    Member
    September 14, 2015 at 10:57 am in reply to: Quebec – Returning to your Coaches Birthplace

    It doesn’t get much better than this.

  • victor

    Member
    September 13, 2015 at 10:19 am in reply to: Looking for XL40 with Series 60

    Do you dry campers and the bears really go to the woods?

    That’s me………cutting edge Jon.

    What we all need is one of the converters to really make the ideal coach and that would have a small nuclear powered engine and electric generating system.

  • victor

    Member
    September 12, 2015 at 10:29 am in reply to: Iverter life span

    I never turn off my inverters. I don’t think the life is impacted because when they function as battery chargers there is really very little going on that would impact their life.

    However……..if you are concerned you have the greatest control over the health of your inverters and one thing you can do is periodically clean out the accumulated dust and lint that tends to collect and always be aware the internal fan must function otherwise heat can build up when the inverter is working, and heat will damage it.

  • victor

    Member
    September 11, 2015 at 8:27 am in reply to: New Gen

    It’s a diesel. If you don’t find some obvious external leak, then the probability of the leakage point goes to the inside. The temperature a diesel operates at will evaporate the liquid coolant, thus the engine oil will appear normal. To be certain it is internal, if you didn’t change oil in the recent past, pull an oil sample and get a test done. What will show up if there is an internal leak point is a group of minerals for which there is only one point source – yep, they are left overs from the evaporated liquid anti-freeze.

    I say this with some degree of experience with an internal antifreeze leak on the really big motor. Serious $$$$ involved there. I too first thought if the oil “looked” normal and not milky then the leak was external. That conclusion was from my experiences building gasoline engines. Diesels are a different breed all together.

    Good luck finding yours and that it doesn’t involve serious $$$$ to fix.

  • victor

    Member
    September 9, 2015 at 8:06 pm in reply to: Engine won’t start -Check Trans Light on

    There is a wire that sends a signal to the dash light to tell you the starter is engaged if the wire is not hooked up it can all work just fine I think but the light on the dash will not come to tell you it’s engaged, if you can find the wire on the starter and unhook it the light should go out but will not come on when you turn the key to start it , then you can hook it up the right way if you want, if you want the light on when you start it. Maybe Jeff will get in on this, But I am pretty sure the wire only goes to the light on the dash that’s it, Maybe Bob will see this he will know too!!!! Or Jon may have the wiring details for the starter and solenoid . But I might be wrong just check it out

Page 8 of 9