victor
Forum Replies Created
-
try the default code of 0100 – it probably thinks it in anti theft mode.
Chances are it is not the standard code, but this is worth a shot. This is sorta typical for when it looses power like it was removed from the vehicle. (No power to the unit at all)I havent seen seen one of those in years – is it really one of the 3 disc in dash players?
-
Michelin and all tire manufacturers have pressures specified based on the weights the axle carries. the weights consider the best tire performance, protection against failure, handling, tire life and safety such as stopping distance.
But if you decide against what the manufacturers want the pressures to be, at the very least make sure the pressures you select exceed the pressures called for in the charts.
-
Thanks Mike, only 24 minutes from the hotel.
A good option for sure.
-
I was incorrect, I forgot my 01 Liberty would not run the dash air unless the coach air was operating.
-
Rick,
I just ordered and received my check valves from Valve Check Inc. They were great to deal with and when I told them that I heard about them from Prevost Community, they told me that several members have recently placed orders with them. Be sure to mention that you are from Prevost Community when you order. I tryed to convince them to be an advertiser on the Prevost Community site. If you can convince them to advertise, Tom might wave your dues for next year.
-
This is a test of a multiple rollover. Tell me a commercial bus frame doesn’t beat out a box bolted to a truck frame.
After it goes dark, keep watching for about 10 seconds for the slo-mo version to start.
-
That was sort of my thought as well…would much rather have chicken legs than something lookin like chicken s*** on my legs….
-
victor
MemberJune 16, 2017 at 6:33 pm in reply to: My 91 Beaver Coach Problems II The Resurrection!I am happy to report that Harry now has his issues well under control. They are not all fixed, but at this point he has them listed and Jeff prioritized them and I heard Harry give Jeff the go ahead.
So Harry has become one of us. He is learning first hand that the internal combustion engine is not what propels his coach down the highway, but it is money. The previous owner of the coach did not do Harry any favors because his home grown “improvements” now expose Harry to an expense relating to batteries and inverters, but overall the needed work is age related and not due to abuse or negligence. It is a nice coach and we all have tried to encourage Harry to spend a lot of money to make it a great coach.
And for those interested his tires are 2015.
And we did a good job of trashing Clarke (me especially) but they did cure the speed issue that related to the throttle position sensor and his charges did not even come close to reflecting what must have been countless hours diagnosing the issue. Bottom line is they did not make Harry pay for their on the job training.
-
For the early systems from HWH installed in the Prevost shells, the power from the circuit breaker was cut and the power went to the HWH control module and then back to the other side of the wire they cut to power the system. The HWH module was supposed to block power back to the Prevost level low rotary switch whenever the HWH was activated. The problem came from the HWH module if it failed. If it did, then no power back to the Prevost system. Later HWH systems had changes to prevent this as the normal was to let the power through the HWH module with no effect. Thus, if you lost the HWH module then the Prevost system stayed powered. But this was later in the 1990s.
For the earlier sytems when they failed you had to find CB82 and wire 24-85-16. You followed this wire as it went to the rotary switch. Along the wire you will find where it was cut as there is normaly a butt connector with a wire going off into the vehicle and then right next to it another wire returning to the place where the wire was cut. This was all in the front electrical junction box.
Once you find this connection you can turn on the ignition switch and see if you have power coming to the first splice connection on wire 24-85-16. Then check on the other splice connection and see if you have power there. If you do not, simply re-connect the two pieces of wire 24-85-16 and the Prevost system is now powered and the HWH is no longer in the level low system.
If for some reason you cannot find this splice of the wire, then gain access to the rotary switch and tind where wire 24-85-16 is connected. Run another wire from a fused or circuit breaker-ed connection to this spot and power the system this way. Or you can do as Jon has described before and simply supply the second solenoid on the manifold for the level low in the front service compartment with 24 volts and you are in ride or travel mode. This should at least get you down the road and home or to a repair shop.
The wire to the drive solenoid is 24-104-18. It was usually blue in color. Plus the later sytems had 5 solenoids and the drive solenoid was the third one down. If you can see the 1/8 inch black air lines that come from the rear of the manifold, the drive position is the only one that has a T-fitting in it as it sends a pilot or control air signal to the front and the rear Norgren valves for the drive position.
-
Deb sent me this link which shows where PC members are able to receive discounts at non Loves locations.
-
at least you had the dues money to pay for the dawn dish soap 😉
-
Very nice upgrade and nice touch of class. Gonna put smiles on our faces when we pull in Thurs. morning for stellar service work. And maybe BBQ with Buddy?
What’s making me nervous is the really cool trailer Jeff just posted for sale at ETLC. Check it out on the ‘For sale’ link above. It looks like an exact match for our bus. I’ll bet Jeff’s gonna tell me I can’t flat tow the Wrangler anymore for some totally-beyond-my-comprehension technical reason. Or he’ll weld the Jeep to the trailer bed.
-
Looks great BA!
Now get back to those air leaks 🙂