Jon
Forum Replies Created
-
DANA – Please create a new post when you are able to share details. Don’t want to miss it 🙂
THANK YOU, Jeff
Cant say much now, but i know there may be someone looking to help out with the cruiseair situation. More to come!!

Dana & Shari Heuson
02 Liberty Elegant Lady -
I could be wrong, but it looks like the silver caps are covering the valve stem that allow you to isolate the port or to open it to the system. This is the way my Cruisairs are done.
Rick
-
Replaced mini airbag on cooling fan belts (3) AX73, now belts are tight for up to 60-72 hours…mini airbag under engine compressor is aired up all the time…must have another leak somewhere.
Front and rear air gauges drop to “0” within 12 hrs time…
-
not sure, if you google the number i gave you it will bring up the bearings, im sure there are other manufacturers that will cross reference to that bearing spec
-
Michelin is all that we ran on our trucks for many years. The tires performed better than any others we tried, the support from both our dealer and Michelin direct was very, very good, and the Michelin retread process was the best we ever used.
I will only use Michelin on any bus/coach/motor home I ever have. I would not even look at anything else.
-
The Meritor calipers used on coaches with the early disc brake set up on the steer and tag axles had two grease fittings inboard of the slack adjuster. Those were to allow the shaft from the slack adjuster to rotate freely. But those who tend to grease buses are usually the low men on the totem pole, with few skills so it was not uncommon for them to keep pumping grease into the fittings until grease was seen coming out of somewhere along the line.
Once grease is pumped in it can only escape from two places. It can ooze out around the seals, or if defective it can ooze out of the grease fitting. The problem is as a bus is driven and things tend to heat up the grease expands and has nowhere to go so it ultimately prevents the calipers from retracting, which causes more heat which continues to keep applying pressure to prevent caliper retraction.
I suspect a lot of brakes have been “repaired” by replacing calipers viewed as defective when in fact over greasing was the defect. I have never done this but suspect the easiest repair if over greased is to remove the two grease fittings and go for a ride that involves multiple long brake applications. I suspect excess grease will expand out of the grease fitting holes correcting the problem. Then to prevent a re-occurance when greasing in the future one or at most two shots in those fittings is all that is required.
-
Chad, here is my Tensioner, a tube with left and right hand threads. When you spin the tube one way it makes the dimension shorter, when you spin the tube the other way it makes the distance longer,
-
Low pressure safety switch on the compressor of our 96 Liberty 40XL/95 chassis w/Prevost full bus OTR ac/heat = Prevost pt# 452406
-
Thanks Don, My Lid has the Hex built into the top to tighten it down, i will need to drill and tap for the Gauge. What numbers do you see with a clean and dirty Filter?
-
Had a friend get his series 60 rebuilt last spring, block and crankshaft were good, parts 24,000 .
-
Jon
MemberApril 20, 2022 at 10:12 pm in reply to: Interesting YouTube on float charging lithium battI posted this video primary for folks that are afraid of using their current invert/charger for lithium batteries. You comment do bring up a big difference in our batteries than the guy in the video. Our batteries general have some type of constant draw.
-
Here are some pictures of the yoke, before and after the installation of the speedi-sleeve. I guess I did not pay very much attention to the condition of the shaft when replacing the seal about 6 months ago. It’s clearly quite bad, and I have no doubts that the re-leaking of the transmission was due to wearing down the new seal.
With the yoke installed, I install the transmission-side of the driveshaft first, as it’s easier to bolt that up because it uses the u-joint straps. The differential-side is a bit more difficult because you have to install the caps to the u-joint after you line up the u-joint in the yoke. You definitely want to support the driveshaft with a strap when you do this. Also, having those holes in the woke pointing up/down make the job much easier, as you can much more easily align the u-joint in those holes before inserting the caps. I cleaned those holes with a light sanding before installing any of the u-joints, and that also made it a lot easier.
-
Both Tom and I should know how many motor home conversions are on the road, but I do not and Tom likely does not know either. Prevost is reluctant to share what they know because they have always screwed with their VINs so competitors like MCI would never know true production quantities.
But after keeping my nose in the market for 32 years, watching coach for sale listings from multiple sources, and going through booms and busts I do know nobody can predict future pricing. Who saw the economic disaster around 2007/2008? Every converter took a bath, and owners who had stretched to buy their coach found their coach market value floating the drain, and the market filled with repos and converter new coach inventory almost impossible to unload.
When fuel hit $50 per gallon prior to this period of high prices customers dried up and owners of brand new coaches were suggesting they would use their coaches less due to fuel prices. This is significant because it show how irrational buyers can be. If someone was willing to use their coach less because fuel was expensive it seems downright stupid because depreciation on their new coach, not being used or used less could be $1000 per day. The Prevost coach market is not rational so predictions about future prices and conditions are likely unpredictable.
One constant that Dick noted in his remarks above is if a potential buyer has that eureka moment and has found the coach of his dreams, he should not hesitate to buy it. Good coaches, especially those with detailed records and a history of good care move fast. It is the dogs of the marketplace that are listed for months. Personally if I am looking to buy a coach, I find one I really like, I am less concerned about its cost than if it meets our needs, and we like it. I don’t flip coaches so over time even if I spent $50,000 more than average market price my financial beating becomes almost irrelevant. I assume my purchase will depreciate to zero value and that depreciation is just one of the costs of ownership.
It is you the buyer who has to decide do you like bragging about how cheap your purchase was, are you going to keep it or flip it, is it the way you want it or are you going to dump dollars you will never see again to change the color of the carpeting, or are you going to be happier knowing you got the bus best suited for you?