Jim/Chris
Forum Replies Created
-
While the lift is going up with a load measure the voltage at the lift pump motor. It may be a bad connection, either on the + or – side.
-
I’m going to check that on mine. With the key off there should be no power to the monitor if it works as I suspect. If there is no power to it then there should be no light, and no way to light a dash indicator light. I will check the 12 and 24 volt inputs and report back.
-
Then you may only have one single tank John.
-
Thanks mystery solved works without batteries
-
I’m puzzled why we keep reading that serious Prevost shoppers keep running into the same issues … difficulty getting information on battery and tire codes, difficulty in getting maintenance history, etc. when dealing with dealers. I wonder how many sales are lost because this information isn’t readily available to prospective buyers. Why should the VIN# be a secret?
I want to confirm what was previously stated that replacing fluids, belts, hoses, bags, break chambers, Norgren valves, and a few miscellaneous do-dads will cost at least $20,000 if done by a reputable, efficient shop that knows what its doing. Tires and both sets of batteries is about $10,000 … been there, done that.
-
So, no one pays any attention to the PC Map, that has campgrounds visited by PC members!
I’ll put my money on the PC Map, I know a member has been there and it either is good or bad. You’ll get a hell of a lot more information than you will from Big Rigs who’s main focus is on advertising and whether your bus will fit on a 70′ site. Good luck with the tree’s.
A lot of people have spent a bunch of their time to populate the map for everyone to use.
-
Raised the awning for the first time yesterday, since we wanted a better view on that side. The rear arm wasn’t too bad to extend, but the front one required a serious push to get it out. Would venture to guess no one had ever extended the awning. After I got it out, polished the arm so it will move easier next time. It does make a difference in the view to raise the awning–wouldn’t want to miss the deer walking by!
-
Bill,
We just stayed at the Whispering Pines Campground and saw all the sites: Rushmore, Crazy Horse, Custard SP, Wind Cave NP, 1880 Train, and biked the Michelson Rails to Trails bike path. Much to do!
Unfortunately, the owners of the campground informed us that we would be their last 45′ motorhome. However, after the owner saw that my Prevost had no hydraulic jacks, I think he was more at ease since he was concerned with our weight ruining their four new gravel sites with 50 AMP.
If you go to Rushmore, plan on staying for the evening program, which is highlighted by Patriotic Music and Ceremony. At the end, all Veteran’s are called to stand on the stage for the “Retiring the Colors” ceremony, and then are given the chance to furnish their name and branch of service. Hooah! Definitely memorable!
-
I think the addition of a 12V water pump was for redundancy more than anything else. The 12VDC pump is normally turned off at the switch in the street side water bay and normally only used if the 120VAC water pump is inoperable. The 120VAC water pump is wired to run off the inverters and controlled by the Techlink system. So either water pump can be turned on/off with the Water Pump switch on the panel. At least that’s how they work on my coach but others may be not be set up the same way.
-
Yes – we have baypass switches (Featherlite conversion) that allow isolation for Gen, Normal or Shore.
We have Curisair units in the bedroom and the front of the coach and they both work, just not enough to cool in the 100 degree temps
-
We dry camp on a regular basis, depending on AC load….4 to 7 gal/hr. Geo.
-
Tom is picking on me.
message sent from my flip phone
-
Thanks Tom!
Great work again!
I added the app, telephone & acct # to my contacts.
-
Sounds Like you found the problem but for future reference on this thread, this is the information Jon was referring too.
This info was from Prevost on this thread.
The advise you gave is correct and the method to lock the fan mechanically is correct.
We sometimes go to the rear junction box and find the two relays for the electrical functioning of the fan clutch. You have relay R78 for low speed and R79 for high speed. If you pull the relay and look at the spades coming out of the relay you will see that they are all marked (30, 87, 87a, 86, 85). Breakoff the 85 tab from the relay andre-install it in the coach. This will cause the fan to be locked electrically. It will stay in high speed now no matter what the engine ECM tells it to do. If the temperture now stays regular and in line with what you were seeing then there is a problem in the control of the fan clutch.
If this does nothing to regulate the temperature ( and you know for sure that the fan clutch is locked in). then you would have to look at the radiator, both externally and internally.
When you have the tab off the relay and you simply turn on the ignition switch(don’t start the engine!), go to the rear and grab the fan blade. It should not turn as it should be locked in electrically. If it still turns but with resistance then I would look to the fan clutch as the problem.
Either way, Jon’s method of mechanically locking the fan with the bolts would enable you to get to the servie facility safely.
One caveat! This mechanical lock up is for use to get you to a place of repair. If you try to use it in place of the controls you will find that the tab(s) will break off and then you would possibly not have a functioning fan clutch at all.If it just threatens to overheat , drive it to the service facility carefully watching the temperature. The normal safety shutdown on the engine for high coolant temperature will still shut off the engine to prevent damage.
There is more info on this thread.
Here is the setup for the two vehicle types. For the XL and XL2 we have R78 that controls the LOW speed or speed 1 and R79 that controls the HIGH speed or speed 2.
For the H3 series we have R84 for the LOW speed and R85 for the HIGH speed.
So if you break the tab (85) off of R78 you will be in low speed all the time except when the coolant temperature rises enough to get the high speed to come on. So turning on the ignition and not starting the vehicle you would find that the fan blade can be turned with just a little resistance. If you used R79 then the fan is locked on high and it moves with engine rpm all the time. It would be then locked when you did the ignition on/no start test you mentioned.
Ideally you should see if the fan will go into low speed normally but not high speed. Then you could use the modified relay in the high speed position to get better cooling all the time.
Keeping the fan locked in electrically this way is not good for long periods as this was a means to get you back home or to your destination and have the problem fixed.
On the extreme end of this issue would be that the fan has failed electrically. Then you need to use the bolts supplied on the fan clutch and you bolt the fan into fixed mechanical drive. This also is a temporary fix as you can eventually break off the tabs and then you have a free-wheeling fan with no control at all.
Davy
-
Bob,
Thanks for the contact name and phone # I’ll give him a call.
Bill S.