Forum Replies Created

Page 42 of 214
  • Dick

    Member
    August 5, 2020 at 7:40 pm in reply to: Tires Losing Air Pressure

    Reece,

    Soap up the sensors, if there is a problem at the seam you’ll see it. Look under the sensor as well where it screws on to the valve stem. Have you soaped the valve stems including the nut that holds it in place?

  • Dick

    Member
    August 5, 2020 at 3:26 pm in reply to: Odometer failure

    I’m in the commercial trucks sales business and we use 30 miles for every hour as a starting point guide if there is no way to read the ECM.

    My Coach does not have an ECM, it all mechanical.

    Hope this helps.

    Rick

  • Dick

    Member
    August 4, 2020 at 9:14 pm in reply to: ADVICE ON CHASSIS BATT ISSUE

    We experienced a similar issue whenever the OTR AC was turned on. Replaced the 4 batteries and all was good.

  • Dick

    Member
    August 3, 2020 at 10:09 am in reply to: Jake Rebuilt

    Glad that having that work done showed significant improvements for you…

  • Dick

    Member
    August 1, 2020 at 10:25 pm in reply to: Taking the 12.7 to 600hp

    Is there a document that outlines what parts make up various DD S60 engines ? Piston, turbo, injectors, ECM program, etc. ?

  • Dick

    Member
    July 31, 2020 at 11:50 am in reply to: Master house battery ground location for 97 CC

    Jerry, you undoubtedly have done a lot of research on this but with nothing more than gut feel I cannot believe combining Li and AGM is a good thing.

    I switched to Li earlier this year and they aren’t anywhere near AGM with respect to voltages or voltage range. I do not know what will occur if you merge Li batteries that operate at 13 plus volts and at 12.2 are near the point where their SOC is well under 30% and the voltage curve is in a near vertical drop off to the battery shut down point, where AGM operate at a 100% SOC at around 12.6 to 12.8 and are always in a slow fall to their dead state.

    Or am I misunderstanding how you intend to use two distinctly different battery types? With AGM it is not even recommended you mix batteries with different ages so I don’t know how mixing with Li is going to work.

  • Dick

    Member
    July 28, 2020 at 8:26 pm in reply to: Secondary charge system indicator

    Its all about your signature when it comes to Marathon advice.

    **

    What Model?

    What serial number coach?

    and then what alternator did you replace, etc.. Picture of circuit may help you understand the circuit of a 2000 ish Marathon with a Delco 270A (House) and the typical 75 Amp Delco (Chassis). My bus not yours ….no other help available other then happy hunting.

  • Dick

    Member
    July 28, 2020 at 10:22 am in reply to: LiFePO4 “Drop in”

    When you are considering lithium batteries of any chemistry alphabet, they all stop accepting a charge, shut down by the BMS (battery management system) between 112 and 118 f, depending on the chemistry. When the batteries are working they will generate heat. the more you are drawing or charging as a % of capacity the more heat they generate. It is not uncommon the be 30 degrees or more above ambient. You need to either ventilate the compartment very well with fans or air condition the space.

    Example, it is 100 degrees in AZ you are parked on asphalt which is 110. 5 degrees of heat from working shuts the charging off.

    Temperature is the Achilles heel of LI batteries.

    Everything is a trade off

  • Dick

    Member
    July 27, 2020 at 9:11 pm in reply to: LiFePO4 “Drop in”

    So, these arent going to just drop in. The voltages offered on the Xantrex freedom 458 inverter are not in my opinion close enough to the manufacture requirements to charge the lifepo4 batteries. Batteries are here! Exploring inverter options now. Batteries want 14.6 charge and 14 float, inverter only offers that at 50 F, and Arizona is never 50 where I live…. Old inverter charging table pictured below. Here is me removing 6 of the 8 (2 were already out) house batteries in 27 seconds because im VERY fast.

    Time Lapse video of removal

  • Dick

    Member
    July 27, 2020 at 11:03 am in reply to: Let’s Talk ISRI seat

    Chip,

    Mine has 2 small screws right in front bottom of seat cushion that look like they just hold the trim in place or something. Remove those and lift the front of the cushion. You might have to remove the dust cover to find them. Mine is held in place by Velcro. ( been a couple of years since I removed mine )

  • Dick

    Member
    July 26, 2020 at 10:07 pm in reply to: Unbelievable

    You need to post a response;

    Reason tire came loose was the RV owner had not changed to summer air

  • Dick

    Member
    July 22, 2020 at 10:47 am in reply to: Chasing new air leak

    Pictured are two (2) manifolds installed on Marathons and known trouble makers.

  • Dick

    Member
    July 22, 2020 at 8:46 am in reply to: Accessory Air Filter and Belt Tensioner Regulator

    Thanks Don!

    Somehow I missed that thread when looking before posting. I am going to give that a try.

    Yes, inside the steering compartment on the right side is where mine is as well.

  • Dick

    Member
    July 19, 2020 at 1:56 pm in reply to: Michelin choice…XLEZ vs XZE

    Hi, what tire size do you run? Never want to “assume”, but it is the 315/80R22.5?

    If so, there is not an XZE offering…. there is a “X Multiway 3D XZE” or the “X Line Energy Z”. What are the differences?

    1. The casing design (bones) of both tires are the same, so the performance for cornering and handling are similar. They have the same speed rating and load carrying capacity (9090 lbs in single at 130 psi, 75 mph)

    2. The X Multiway 3D XZE is directional, so if you decide on this tire, make sure the tire dealer is aware of it… the arrow on the sidewall is quite small.

    3. The X Multiway 3D XZE starts with a higher tread depth (21/32″) than the X Line Energy Z (17/32″). Chances are, you will not wear out either tire.

    4. Fuel efficiency! Hands down, the X Line Energy Z is much more fuel efficient… 7% better than the XZA2 Energy, which it replaced.

    I would encourage the use of the X Line Energy Z over the X Multiway 3D XZE… the reason Michelin offers the XMW 3D XZE is for fire trucks and construction vehicles that are exposed to tight turns, curb hopping.

    Hope that helps.

  • Dick

    Member
    July 18, 2020 at 10:58 pm in reply to: Pictures of bare Prevost slide components ?

    Interesting. I’m particularly interested, as I just went through a gen 2 to gen 3 slide controller conversion for the front and rear slides.

    Interesting that the slide seals pressure recommendation is now 8-10 psi. Sticker by the regulator states 15 psi.

Page 42 of 214