Forum Replies Created

Page 28 of 214
  • Dick

    Member
    April 29, 2021 at 10:28 am in reply to: Tips for Changing Coolant Line from Compressor to

    The crows foot will loosen it, I’ve found in tight spots wrenches with different angles help. I have two sets of AN wrenches, one is straight and 30 degree, the other is 30 and 60 degree. You can turn the wrench 180 and get pretty much any needed angle to keep the nut turning.

    The angled wrenches -may- help:).

  • Dick

    Member
    April 28, 2021 at 4:30 pm in reply to: Hub cover

    Thanks everyone. Looks like I can find something similar on those web sites.

  • Dick

    Member
    April 26, 2021 at 10:12 am in reply to: High Idle not steady after battery change

    Just guessing this morning … are you absolutely 100% sure the new batteries were 100% wired correctly?

  • Dick

    Member
    April 26, 2021 at 1:07 am in reply to: any old 727 folks out there

    I got to ride the jump seat on a United 727 just once. As a low-time private pilot, I was fascinated by the flight engineer’s panel.

  • Dick

    Member
    April 25, 2021 at 10:08 pm in reply to: New Silicone Hoses Installed on Webasto

    Hi Bill… Now replacing about 40 feet of coolant hose going to my water heater and back to engine. I swear I believe none are easy to change. Using Gates Green Stripe. The old was rubber date-stamped 2006 and it was likely still good, but since changing from coolant with SCA’s to Final Charge, decided to go ahead and change all the rubber I could do.

  • Dick

    Member
    April 23, 2021 at 7:18 pm in reply to: LED headlight upgrade for XL chassis

    very nice. where can i get one of the black prevost community plates. lol

  • Dick

    Member
    April 23, 2021 at 12:56 pm in reply to: LED headlight upgrade for XL chassis

    Fantastic! Well done.

  • Dick

    Member
    April 20, 2021 at 11:18 am in reply to: Prevost slide room locks

    Jon, I may be using the wrong term “manually “.

    on my slide control panel in a bay, there are 2 guarded screws, one for salon and the other for bedroom.

    there is a caution to insure the slide is fully closed and then the screw can be turned 1/4. This allows air to the pin and closes it.

  • Dick

    Member
    April 19, 2021 at 4:21 pm in reply to: Bus Not Raising to Drive Height

    Thank you for the suggestion, what is th best way to go about doing that? Still trying to figure out this suspension stuff

  • Dick

    Member
    April 14, 2021 at 5:14 pm in reply to: How far do I go with this? etc. 1989 XL CC 8v92TA
  • Dick

    Member
    April 14, 2021 at 9:58 am in reply to: DN50 voltage regulator and Relay

    I also have a long 24v Delco aalternator for chassis batteries.

  • Dick

    Member
    April 13, 2021 at 5:11 pm in reply to: House battery monitor

    Thanks Tom, I could get the 712 to have bluetooth. I may be misinterpreting how the shunt works. My issue is how to get it to keep track of power going in and out on the 12v center tap. I will not have an accurate charge state if its only monitoring the 24v connection.

  • Dick

    Member
    April 7, 2021 at 2:10 pm in reply to: Damn that Tom

    Chad, most all antennas are designed and tuned for certain frequencies and may not work on the Pressure Pro system. Have no idea what the frequency of the system is but it may help and it may not.

    The antenna you have may pick up and transfer some of signal or enough to help with your problem.

    Worth a try

  • Dick

    Member
    April 6, 2021 at 7:58 am in reply to: Separation between Chuch and State

    Brake and wet tank should not drain with aux, check valve.

  • Dick

    Member
    April 5, 2021 at 1:43 pm in reply to: Bay Door Damaged

    Thank you All for the great Ideas. My only issue with using our do it all guys would be time . Donnie would be close as we are in Fla however from everything I have ever heard if i ask him how soon he will say try another shop lol

    Jon, there will be no pulling this door apart she is crushed . I have a lead on a door from vision RV parts however that door will need to be polished .

    Has anyone ever used Walter D Andrea Bodyworks ?

Page 28 of 214