Dick
Forum Replies Created
-
The H3-45s had NO Prevost slides until 2003 or 2005… many of the early H slides were from HWH.. we had a 1998 Vantare with 2 slides made by HWH. I think there was another brand also in the early 2000s.
It’s very easy to see a big difference in the early H slides as many of them have exposed mechanisms…. don’t let that be a deal breaker for you however as many folks prefer the slides that don’t have the expensive air seals.. the HWH are very servicable and have ordinary easy to replace D type seals.
Cheers, Diane
-
Tom, new pics on the ladder system?
-
Mark
We saw that coach when we were there, it really took a hit.
Your coach is really a beautiful coach.
Thanks again for the lounge code,
Chris
-
Bernie & Tom, the Black OEM shocks for the XLII are manufactured by Sachs. The Yellow, Blue & Black shocks for the XL chassis are built by Monroe, and are a little less $’s.
-
TG, does the fit inside the original opening in the cabinet or is sitting upfront?
-
Dick, according to the owners manual, XL / XLV should use 13ft extension, H3 should use 17ft
-
Mine is stored in the 3rd bay on the drivers side on a shelf above the inverters. Marathon also put a jack and various shore power adapters there as well. Mine is an XLii so I do not know whether that is relevant to yours.
-
In Panama, many of us have tankless whole house, electric hot water
heaters that give unlimited hot water. Even though our water is unbelievably soft, the manufacturer
still recommends that you flush the heater’s coil system at least once a year to remove scale buildup. The
system is supplied with “T” fittings that allow you to shut off the
water and hook up a flush system. I use a small submersible fish tank circulating
pump (about 60 gal/hr) in a plastic pan and use hoses to connect to the cold water inlet side then route a hose from the hot return side back to the plastic pan. I then put two cups of vinegar and a gallon of
water in the pan, plug in the pump and let it run continuously for about 2 hours. I do this on my
January 1 schedule of things to do, such as replace the AAA backup batteries in
my thermostats, replace smoke detector batteries, etc. That way I do not forget. It seems that this
might be a good procedure for the Aqua Hot coil, especially if ever using Florida water
that seems to scale up if you just look at it. -
Good advice. Even though we have not had to replace a refridgerator, I’ve seen enough of them done at Parliament to know that it is one of the the jobs not worth doing yourself. I think Truk would agree….We saw his being done, and if some idiot hadn’t glued the windshield in previously, he would have been gone by lunch. Spoke to Dick the other day and trying to figure the best place for him to go up here (Wi). Geo.
-
Thanks … very helpful … just in case.
-
Dan,
Those two guys were poorly trained. Even using a flat blade screw driver to insert the welting in the gasket instead of the proper tool it is a one man 20 minute to 40 minute job.
We have coached owners who never replaced a piece of glass in their lives at rallies and I don’t think anyone ever took more than 45 minutes and that include the time spent dealing with ball breakers.
-
Thanks Joe. That was very helpful. I’ve done many searches over the past months and these are the best so far. I like the one with three holes; two USB and one volt meter. I just bought a new race trailer and the volt meter would enable me to monitor the charge in battery in the trailer for the winch and lights.
-
Maybe John Hawkins will see this and chime in. Any of our busses with IFS need a specific type of tow equipment as the bus must be picked up by the front wheels. If a tow operator tells you otherwise, send him packing. They must also have the proper tools and knowledge to disconnect the drive axles or drive shaft. We have been towed once while we had Good Sam and knew ahead of time that the dispatcher would be of little help. You may contract on your own and then call Good Sam and tell them why. They will then reimburse you direct(they said 4-6wks…it came in 3). Geo.
-
Don etal wrote: “110v receptacles w/usb chargers”
I’m thinking about doing that with all the receptables in the coach. Anyone else do the same thing? I do like the GFI/GFCI receptables with little LED lights which tell you if the receptable/circuit it hot or not.
I’m also looking for a 12volt to USB outlet, device, etc. that could be hardwired into the coach. It seems like the only thing I can find are the ones corded to a cigarette lighter.