Forum Replies Created

Page 88 of 2304
  • Archived

    Member
    January 15, 2021 at 4:11 pm in reply to: Coolant Temp gauge scale

    Shame on you, Dick. Unless you only few all glass cockpits steam gauge planes used needles and dials. When monitoring the engine gauges it did not take long to know where to see oil pressure CHT, EGT, MP, voltage, oil temp, etc.

    I am sure you watched your vacuum gauge, fuel gauges (and mentally compared that to your time airborne) and then not only knew what was normal on the gauges, your ears would instanty alert you of a change in sound or a noise.

    Our buses talk to us in the same way, and if we spend more time paying attention to the bus, and less to the smart phone we almost always know when something has changed and might need attention.

    BTW, the guys that installed the digital readouts for everything either spent most flight time watching readouts bounce around digitally, or went blind watching way too much info and quit watching after a while.

    Call me analog man.

  • Archived

    Member
    January 15, 2021 at 12:14 pm in reply to: Coolant Temp gauge scale

    Jon wrote: “The best protection however is for normal, correct indications to become locked in memory”

    Has Jon forgotten that’s much easier said than done?

  • Archived

    Member
    January 14, 2021 at 10:47 pm in reply to: Norgren Valve Replacement

    Thanks Don.

    I am just outside the VIN range in the bulletin (T1025914) – and it’s an XL40, not a 45, so it would appear to be the late type.

    Based on this, what valves do I need to change the other three, if you have that handy?

    Getting closer…

  • Archived

    Member
    January 14, 2021 at 8:46 pm in reply to: Webasto Nozzle Replacement Tips / Tricks ??

    Thank you, Colt!

  • Archived

    Member
    January 14, 2021 at 8:25 pm in reply to: Replacing Starter

    Jeff did the same for us a couple of years ago, peace of mind category! Geo.

  • Archived

    Member
    January 14, 2021 at 6:36 pm in reply to: Just got hit!

    According to the Zip Dee website they send screws. I have called multiple dealers here in the MI area and the responses are all about the same…………We used to be Zip Dee dealers………

    I will give Busman a call. I also tried to contact Zip Dee by e-mail and we will see if anything comes of that. We may be finishing work here in Detroit and could drive back down to see Jeff at ETLC!

  • Archived

    Member
    January 14, 2021 at 12:48 am in reply to: Just got hit!

    International Bus Parts should have rivets for you. Steve Kolb will be ready to take your call in the morning.

    You’ll probably want to get a really heavy duty river setter to set them. Something with long arms.

  • Archived

    Member
    January 13, 2021 at 2:21 pm in reply to: Possible Head Gasket issue

    Little update to share . I paid for the New to me used Genny and it is on its way to Mototcoach Clearwater. A friend and I are in the process of removing the radiator and fan. The plan is to recore the radiator and most likely replace the motor in the fan prior to sealing everything back together .

    As the the motor I bought she has 2,800 hrs on her . besides a oil and filter change and a new belt what else would you do if getting back their involves 7 hrs of work . I also will replace all air springs and eliminate the compressor in that area and set it up like Marathon .

    any other ideas while I’m back their ?

  • Archived

    Member
    January 13, 2021 at 12:11 pm in reply to: This CAN’T be good

    One thing I do like about the Liberty is that there is a voice warning if the fresh water tank is getting low and if the holding tank is getting full…. (this can be turned off).

    Something to the effect:

    “Potable water tank is getting low”

    “Holding tank is reaching full”

    It’s a ladies voice…. we’ve bonded. LOL!

    Safe travels!
    Mark

    PS. FTBill, glad that you caught it in time!

  • Archived

    Member
    January 12, 2021 at 4:13 pm in reply to: Damn that Webasto!

    Don, et al,

    I looked the the Detroit Diesel table. Where do find coolant for DD 8V92? I apologize but I did not find it.

    R

  • Archived

    Member
    January 12, 2021 at 4:03 pm in reply to: Replacing Starter

    x2 what Jeff said, and please let us know part#, source, and price.

  • Archived

    Member
    January 12, 2021 at 7:32 am in reply to: Damn that Webasto!

    I also wanted to thank Rudy for that information. As soon as I get a day off I will open the box and see what I can find. I have done a lot of work on the Webasto on my ’88 coach so I am familiar with the innards. I will give your suggestions a try.

  • Archived

    Member
    January 11, 2021 at 7:56 pm in reply to: Loss of K-9
  • Archived

    Member
    January 11, 2021 at 7:48 pm in reply to: Replace for Belt Tension Air Regulator

    If I remember, and if it’s leaking and valve has a 1/4″ female open pipe port it’s leaking from, plug it. If you have to change belts pull the plug. It’s regulated for air pressure and wasn’t leaking there. A few years ago called Prevost Houston and that’s what they told me to do to get her in. Been 2 years and haven’t replaced leaking valve yet. . If cylinders leak Prevost has a parts kit for those. I have 2 and need to install one.

  • Archived

    Member
    January 11, 2021 at 4:28 pm in reply to: What year did Prevost start independent suspension

    Somewhere around T5880. Jim (Coloradobus) can give the precise VIN.

Page 88 of 2304