Forum Replies Created

Page 75 of 2304
  • Archived

    Member
    March 22, 2021 at 7:29 am in reply to: Prevost h3-45 double slide vs Dynamax DX3

    After having driven both a bunch of miles, here are my comments.

    The Dynomax is truck chassis, it rides like a truck. Even though it is on airbags and not springs it rides like a truck of the same vintage. The noise level is greater. If you like a front engine unit it is a better choice. They are also popular with folks that tow heavy trailers, ie race cars, large horse trailers, etc. Also there ae some parks that do not allow anything except a Class A, which they are not. They do tend to have more beds, so that is good for a family. Overall I prefer the Prevost for the ride and quiet.

  • Archived

    Member
    March 22, 2021 at 6:51 am in reply to: Prevost h3-45 double slide vs Dynamax DX3

    After you have owned others and driven them Prevost is hands best

  • Archived

    Member
    March 22, 2021 at 6:09 am in reply to: Garmin BC 40 back up camera

    Ralf,

    Regarding the display the only port on the back of it is the power port which is a 12V connection. the camera is a wireless unit with no wired connections. Somehow Garmin has programmed the camera or display to only allow the camera to operate when the coach is standing still or when in reverse.Best case would be if someone knew how to reprogram so it could be on all the time. If not does anyone know of a wireless camera that would connect to the display and stay on 100% of the time.

    Cal

  • Archived

    Member
    March 20, 2021 at 8:56 am in reply to: Valve adjustment

    It’s been about 3 years, but around 500.00 if I recall. I dry camped in their parking lot so it was cold in the morning. Marathon sends there DD work to Ocala.

  • Archived

    Member
    March 20, 2021 at 6:45 am in reply to: Garmin BC 40 back up camera

    Ralf, I am not sure that is possible since the backup camera is battery operated. Since the entire system is operated on GPS backing up must trigger it on and when going forward turns it off.Any more thoughts?

    Cal

  • Archived

    Member
    March 19, 2021 at 3:57 pm in reply to: Garmin BC 40 back up camera

    Yes if you don’t want it on a switch find a power source that is active when the ignition is turned to the on position and the camera will be on all the time. Just wire the trigger wire to the power source that is on with the ignition

  • Archived

    Member
    March 19, 2021 at 9:05 am in reply to: Coolant Filter

    A little pricey for the pair they were like $150 but they will be correct

  • Archived

    Member
    March 17, 2021 at 1:46 pm in reply to: Cruisair Question

    My guess is any refrigeration supply house. Some of them need to see your credentials if you are buying refrigerant, but they can and will sell other parts with no problem. They typically cater to the trade only, but I have never had issues with getting parts.

  • Archived

    Member
    March 17, 2021 at 11:31 am in reply to: Cruisair Question

    Anyone know where I can purchase replacement valves?

  • Archived

    Member
    March 16, 2021 at 2:01 pm in reply to: Zip Dee Pull Down Straps

    I have replaced all of ours . They are riveted to the tube . You need to measure the length and provide to color to Zip-Dee . They will ship you one out . Would be a good project to do at a Rally 🙂

  • Archived

    Member
    March 15, 2021 at 11:39 pm in reply to: Cruisair Question

    Pressures are normal, i swapped out capacitors twice already with working ones even the relays and nothing I’m starting to think there is a clog somewhere and it’s building to much pressure on start up so the compressor over works and draws the heavy load

  • Archived

    Member
    March 15, 2021 at 3:35 pm in reply to: Cruisair Question

    Sounds like it is over charged

  • Archived

    Member
    March 15, 2021 at 8:12 am in reply to: Cruisair Question

    Sounds like it is trying to start against a high head pressure. Is the system equalizing when it is not running? Put a set of gauges on it and see is the low and high sides are equal prior to starting. If not it may be a clogged dryer or stuck expansion valve.

  • Archived

    Member
    March 14, 2021 at 10:45 pm in reply to: Cruisair Question

    I put the working unit which I just recently installed a compressor on in place of the one that is causing issues since it’s used for the bedroom. So I will fool around with it tomorrow see what I can come up with. I’ll keep you guys posted

  • Archived

    Member
    March 14, 2021 at 5:03 pm in reply to: Cruisair Question
    I don’t understand what you mean when you said “loading up”?
    My CruiseAirs have two capacitors each. A “start” and a “run”. Change both of them.

    Grainger part #s:

    run = item # 30D620

    start = item # 6FLU5

Page 75 of 2304