Forum Replies Created

Page 2270 of 2304
  • Archived

    Member
    March 6, 2012 at 10:49 pm in reply to: Noise in rear leveling system.

    Tom I added it and plumbed it into the Front Aux tank with a check valve. I get the same groans and moans from the rear with shop air. It kind like an old man getting up off his knees.

  • Archived

    Member
    March 6, 2012 at 5:46 pm in reply to: Air bag/Prevost question

    Ace,

    First, my response is based on some assumptions. First, your gauges are the gauges Prevost uses for brake system pressures. Primary and secondary. The second assumption is nothing has been changed on the coach to mix the aux system with the brake system. By that I mean nobody has tapped into brake air for any purpose other than brakes.

    Here is basic information that may help you isolate and understand the air systems. When you park a bus there is no air pressure beyond the brake system air tanks, treadle valve or relays. The fact your brake system gauges went to zero suggests there is a leak in a component or component common to the primary and secondary brake systems. Air dryer? Treadle? Leaky fitting? Leaky or open petcock? Etc.

    If you are looking for a priority, start making the brake systems leak free. They should sit at XXX perssure for a very long time. Mine will not drop below 100 PSI even after sitting 3 months.

    If the entire coach is settling down evenly I need to know if you have a level low system because that kind of issue has me puzzled. I cannot think of a single point that would enable a pressure loss in all the air bags with the level low system. As a point of information on a conversion coach made afer 95 or 96 auxiliary air pressure can go to zero and the bus will not drop if the suspension valves and air bags are leak free. On coaches prior to that if aux pressure drops below 30 to 35 PSI the rear will drop when the 3 port Norgrens in the rear open the path to exhaust tag axle air.

    You are dealing with at least two unrelated issues. The starting point is to do some basic leak detection on the brake systems and I would suggest you also confirm the check / protection valves are functioning also because they might be a contributing factor.

  • Archived

    Member
    March 6, 2012 at 4:32 pm in reply to: Air bag/Prevost question

    Thanks for the help guys!

    I brought the bus home from the shop where it sat for a few days before I could fine time to bring it home and after it aired up to 120lbs everyone at the shop says it stayed up for a couple days before settling down.

    When I go to pick it up and bring it home,I aired up, drove it home without issues! After parking it in its spot, I shut it down and observed the gauges. Both NEW gauges read 120lbs. This was at 6:03 pm. At 7:15 pm the gauges read just above 110 with no apparent drop in suspension! At 7:30 am the suspension is all the way down on the tires and both gauges read ZERO!

    What gives?

  • Archived

    Member
    March 6, 2012 at 4:31 pm in reply to: Air bag/Prevost question

    Thanks for the help guys!

    I brought the bus home from the shop where it sat for a few days before I could fine time to bring it home and after it aired up to 120lbs everyone at the shop says it stayed up for a couple days before settling down.

    When I go to pick it up and bring it home,I aired up, drove it home without issues! After parking it in its spot, I shut it down and observed the gauges. Both NEW gauges read 120lbs. This was at 6:03 pm. At 7:15 pm the gauges read just above 110 with no apparent drop in suspension! At 7:30 am the suspension is all the way down on the tires and both gauges read ZERO!

    What gives?

  • Archived

    Member
    March 6, 2012 at 9:03 am in reply to: POLISHING WHEELS

    While my exterior is fiberglas, I wash it with a spot-free detergent.

    But, I have had some good results on metal coach exteriors using/adding Rain-X solutions to the wash/rinse water, which, in glass (and seems to help metal too) , fills in the pores of the metal and that seems to reduce the spotting after a wash.

    I also add it to my rinsing solution.

    Just my cent and a half.

  • Archived

    Member
    March 6, 2012 at 6:53 am in reply to: WILL YOU BE OUR SECOND WINNER?

    I was thinking it was an SOB (that’s Some Other Brand), and adding $100 of fuel to that would definitely uncrease its value.

  • Archived

    Member
    March 6, 2012 at 6:40 am in reply to: Know your power source

    Greg,

    What 12/24 compressor do you have that is robust enough to handle the aux needs? All of mine have been 120v.

  • Archived

    Member
    March 5, 2012 at 10:21 pm in reply to: WILL YOU BE OUR SECOND WINNER?

    Is that a Liberty ProtoType?

  • Archived

    Member
    March 5, 2012 at 4:11 pm in reply to: Insertions

    This is a test. I do not get a drop down with “browse”. To post the image I ignored the URL part and clicked the upload button. This let me choose what I wanted to post from my files. I selected the photo and followed the prompts.

  • Archived

    Member
    March 5, 2012 at 12:56 pm in reply to: Air leak repair

    At another time in my life I used to rebuild my Norgren valves thanks to the excellent availability of repair parts or kits from Norgren. It was a great learning experience but the bottom line was that I had to recognize two things. If the valve failed because of corrosion internally due to moisture getting into the system, the valve body was scrap. It made more sense at that point to buy a new valve. My last replacements were new, but the valves I removed were shown to be corrosion free so when the time comes to replace my current valves I will rebuild the old set. Jim has nailed it about the end cap screws and I find a very sharp rap on the screws with an impact tool plus soaking in penetrating oil helps the binding of screws that comes about because steel screws in an aluminum body is a sure prescription for corrosion.

    The second thing I learned is if the object of repairing or replacing valves is leak free operation then regardless of whether rebuilding or buying prior to installation I do a quick bench test to insure the valve is leak free. I ended up making a simple rig with parts from Lowes to insure there were no leaks because after installation trying to find a valve leak is very difficult. They can leak internally past the seal, or they can leak sideways out the end caps. The leaks are very difficult to isolate when they are part of the air system on the bus.

  • Archived

    Member
    March 5, 2012 at 10:49 am in reply to: Insertions



    Is there a way to upload pictures by the browsing method instead of the URL method?

    The software of this forum reduces the size of digital photos automatically to a usable size for the Avatar, are photos uploaded to the body of the forum also automatically resized or must they be the correct size prior to uploading?

    I suggest you have a locked thread at the page top with questions and answers about the forum functions and policy of posting.

    JIM

  • Archived

    Member
    March 5, 2012 at 10:32 am in reply to: Air leak repair

    Leaking out of a Norgren exhaust port, may mean there is a leak in some component up stream from that port, or it could be an intermal leak in that valve.

    The rubber seals on the valve spools appear to be conventional O-rings but are infact special proprietaryy washers. These washers can develop nicks and cuts that will cause leaks.

    Note the roughness of the third rubber from the left, it is too rough to seal.

    This is the shape of the rubber in the groove. Note the nick that surely did cause a leak.

    My recommendation; if you suspect the valve at fault, replace it with a new one, you will then be good for about 10 years. Your job will be done and you can enjoy the coach. Save the old valve and at your leisure take it apart and study the parts and pieces with a magnifying glass to satisfy your curiosity and understanding. If you discover that the valve is not too corroded and looks reusable, grease it up and reassemble it for a spare.

    Some internal parts are available from Norgren. If as is often true the small screws break you can use all the other good parts for spares, but not the body with the broken screw.

    JIM

  • Archived

    Member
    March 5, 2012 at 8:12 am in reply to: Prevost Press Release

    There are two ways you and others can help Tom. First, encourage all Prevost conversion coach owners, drivers and enthusiasts to become members and participate. The more of us that congregate here the more willing will be the support and participation of the very people we need and rely on such as Prevost Car and our converters and suppliers. I am not suggesting people abandon whatever group or club they now belong to, but that they view this site as a supplement to their group or club.

    The second thing you can do is share your knowledge and experiences. People new to Prevost are in awe of the complexity and size of our coaches, so those who have experience can offer very good help and advice. Just knowing there is a place where they can ask questions is often comforting to folks. Your experience with your window if shared with a new owner sometime in the future will give someone a lot of comfort knowing they are not alone and that it is something they can tackle if they are not convenient to a service facility.

  • Archived

    Member
    March 5, 2012 at 7:47 am in reply to: Power Source for these items

    Rob,

    Over the years I have seen a number of converted coaches that have had chassis and house items powered (air or electric) by wherever and whatever was easiest or closest. It drives people nuts when they have to trouble shoot. Maybe not the owner or mechanic that hooked stuff up initially, but the poor folks that have to deal with it at a later date.

    Prevost builds conversion chassis with distinct places to tap into the air (auxiliary only) or electric. Converter do a great job of sticking to those places so it protects the integrity of the chassis and the house. Any time something in the house is hooked up to the chassis just because it makes fishing wires or air lines easier it tends to drive folks nuts at a later time when they try to figure why the batteries keep going dead or they keep losing air pressure.

    A final note…….document everything you do. Create your own maintenance and shop manual so when future repairs or modifications need to be made it is much easier for you or subsequent owners to understand why and how stuff was hooked up.

    Having said that, Prevost has several places for electrical connections available for both key on and key off power in both 12 and 24 volts. Any time I do anything on my coach, I try to make sure if it relates to the chassis I use those connections, and if it relates to the house I use power from the converter’s electrical connections just so I can keep track of stuff.

  • Archived

    Member
    March 5, 2012 at 6:59 am in reply to: Air leak repair

    Replaced the Norgren air filter Saturday and that stopped that leak. Was going to replace the Norgren in the engine bay that controls the rear view camera door, but it is so different and I am going to need more parts. It is the same function as the existing but is bigger, mounts different and the air ports are flipped in relation to the electric plug.

    Also replaced the fitting on the left dash guage and stopped that leak.

    I also have a couple of Norgrens that leak out what I believe to be the exhaust port (has the red plastic screw with slots on the side in it). Can this be repaired with an O ring or does it have to be replaced?

    Thanks again!!!

Page 2270 of 2304