Forum Replies Created

Page 2271 of 2304
  • Archived

    Member
    March 4, 2012 at 11:29 pm in reply to: Power Source for these items

    Rob, so far as I know, all the Prevosts have an air operated interior step “ledge” or cover. I don’t know of anyone that has an electric step , as the air leveling brings us low to the ground if we so desire. When this does not present itself as an option, I , for one, carry a small 4 legged adjustable step that I got at an FMCA rally. Good luck and post a pic or two, it will be interesting.

  • Archived

    Member
    March 4, 2012 at 11:04 am in reply to: POLISHING WHEELS

    The most extreme material I use on my stainless sides is car wash soap if I have gone through some nasty weather, otherwise it is just water. I have never waxed, polished or otherwise done anything with the stainless.

    I always dry the stainless immediately after washing, drying it in sections if need be to prevent water spots.

    Attribute my lack of effort to do anything with the stainless to laziness. Polishing wheels periodically with a buff, or shining them with a polishing compound such as Wicked is one thing, but I sure do not want to start something with the stainless because that goes beyond anything I am prepared to do routinely.

    If my coach gets a little too hazy for my taste and I want to refresh the shine on the stainless I will have a professional polish it. That sounds easy, and I guess paying someone to do it is easy, but the process, if done correctly is not simple or easy. To start a sanding of the surface is required, a very coarse grit to start to remove deep scratches, working gradually to a very fine grit (1500 or maybe even finer) before the final polishing which might even entail various grades of polish or jewelers rouge. What is critical about polishing is to avoid heat which will screw up the panels and cause them to buckle in severe cases.

    So far my stainless is tolerable. Not great, but not bad. As an aside when I got the coach I had a ding in the rear bumper. It was not really noticeable, but it was there so I decided to remove it. I pressed the dent as flat as possible from the rear using a hydraulic jack and the weight of the bus. I beat on it a little with a hammer, and then I started sanding it with a belt sander and about 120 grit. Once I had the surface smooth, I worked from 320, to 400, to 600 to 1000, and then finishing up with 1500 grit. Then I got out my buffer and with white rouge put the final polish on it. It is not perfect, but it looks pretty good for an amateur. I know where it is, but most will never notice where it was repaired. I can do that on the bumper because it is a small section, and mostly because of the thickness. On the lighter gauge sides I would be asking for trouble, hence my intent to use professionals when the time comes.

    My guess is Wicked and polishes like that work well on aluminum, copper, brass, etc because they remove corrosion. Our stainless does not corrode as it ages, but gets hazy due to microscopic scratches that are created over time. The only way to remove them is to buff them out using abrasives, albeit very fine abrasive materials.

  • Archived

    Member
    March 4, 2012 at 10:29 am in reply to: POLISHING WHEELS

    Jon,

    How does the Wicked Polish work on the stainless steel of the coach?

  • Archived

    Member
    March 4, 2012 at 6:36 am in reply to: Prevost Press Release

    I think due credit should be extended to Di and Nancy who finally found a project to keep two A-1 men occupied and out of their hair.

  • Archived

    Member
    March 3, 2012 at 8:24 pm in reply to: Noise in rear leveling system.

    I had a similiar noise last fall while hooked to shop air in the garage. After I rebuilt the air dryer, it stopped. I never did really figure out where it was coming from, but it sounded just like you described. If I unhooked the shop air, the sound would end.

    I suspect the noise was air escaping from the wet tank through the dryer.

  • Archived

    Member
    March 3, 2012 at 7:14 pm in reply to: Prevost Press Release

    I feel honored to be just a very small part of this.

  • Archived

    Member
    March 3, 2012 at 7:05 pm in reply to: Towing More Than 10,000 lbs?

    The old 10,000 pound hitch was a accident waiting for the right time to fall out from under the coach, but it had not found the most proper time to do so (police watching, heavy traffic ETC)

  • Archived

    Member
    March 3, 2012 at 7:03 pm in reply to: Cricket Carts

    There are times, when a golf cart will come in handy. I also understand, that there are people with limitations, where a cart may be the only way to provide mobility.

    However, for many other reasons, THIS should be the transportation of choice:

    http://focusdesigns.com/sbuv3/

    🙂

    Ronald

  • Archived

    Member
    March 3, 2012 at 6:57 pm in reply to: Cricket Carts

  • Archived

    Member
    March 3, 2012 at 6:33 pm in reply to: Cricket Carts

  • Archived

    Member
    March 3, 2012 at 5:41 pm in reply to: Prevost Press Release

    Congratulations and thank you for the site!!

    Robert

  • Archived

    Member
    March 3, 2012 at 2:06 pm in reply to: Riverbend RV Show – Ft Myers

    MMillennium Coach

  • Archived

    Member
    March 3, 2012 at 1:46 pm in reply to: Prevost Press Release

    I think I speak for Tom as well, but all of you in the Prevost Community deserve the thanks. Without your participation and support we would not be where we are today.

    It is important for us all to remember that when we can all come together in one site all of those who provide us with support from Prevost Car, to the converters, to the suppliers of parts, devices and support services such as financing and insurance can justify being here and also participating on this site as Prevost does. So thanks to you all and we hope to encourage many, many more members to join us.

  • Archived

    Member
    March 3, 2012 at 9:28 am in reply to: POLISHING WHEELS

    Will we at OysterFest be able to purchase tickets (and protective eye wear) to view this 8th wonder of the world?

  • Archived

    Member
    March 3, 2012 at 9:23 am in reply to: Prevost Press Release

    Let me be the first to congradulate Jon and Tom getting the official backing and support from Prevost Car. Your dream has come true in just a few short months.

    We are all proud to be a part of the Prevost Community and with the blessing of Prevost Car it just takes it to the next level.

    Great job U- 2. Impressive

    AL

Page 2271 of 2304