Archived
Forum Replies Created
-
Hi Ron, copy the beer in the frig concept!! and I appreciate you
taking the time to explain your system.So on one hand it appears that it is possible to go solar or
at least run some appliances, if you are aware of and take care to understand
the demands of the wattage involved. I
have no intention of running everything at once on solar and I do use my
generator daily when traveling and sometimes all day long (and night) depending
on the demand. But dang, I really I was hoping it would be more “practical” to have
a panel or two on the roof to help cut down the time of running the gen and
charge the batteries but it seems we are not really there yet. If you have any
resources or books that might be a good place for me to start reading up on
this I’d appreciate that too. Thank you. -
Ace,
It’s a good thing you’re not asking Jon that question!!!

-
Try again Granvil, no text..
-
Installed the new batteries today. It was raining today so I had time. It took all of 35 minutes. Just a note to all as a helping hint. When I took the cables off each post I wire tied them together so as not to mix up the order.Some post had 5 wires on them! It would be my luck to have a wire I didn’t know where it was supposed to be hooked to. This could have taken longer had I consumed a drink or two but I had to drive after. Rick
-
It is fixed…
I called Worldwide Equipment in Cincinnati. (Business Card Below) They are listed on the Prevost website as a certified repair center. They sell and work on Volvo so they do more work on Volvo engines in Prevost busses than they do on the rest of the Prevost systems. They were upfront about that on the phone but they were pretty sure they could take care of the air leak I described.
They lifted the bus while it was running and I lifted the tag so they could spot the air leak. The mechanic could not find a leaking valve underneath but found the big leak was in the canister on the side away from the tire. When he took it apart the rubber diaphragm was not in terrrible condition but it was completely out of place.
This is the connection below the canister and he discovered that the pin and clevice and was frozen and would not allow that rocker arm to move properly. He thinks this put stress on the whole system and pressure on the diaphragm and moved it out of its proper place in the canister. It took him quite a while to “unstick” the joint for lack of a better word. Even though the diaphragm wasn’t bad he replaced it since we had a new one and it is so cheap. I am sure it has been in there for years, possibly 17 years.
Here is a picture of it from the other day…
The folks at Worldwide Equipment were very helpful, especially Dan the mechanic that actually did the work. I was in the shop about 4 1/2 hours and they tried to charge me for just over 3 hours labor even though they were waiting for the diaphragm most of the time. They did knock 1/2 hour off without any hesitation.
It would have cost me about $175 in diesel to detour from my route to Prevost in Nashville. They could have fixed it quicker but it would have had to be almost 2 hours quicker to save me any money and I would have spent 5 hours driving. Worldwide was 25 miles from where I am this week.
All in all it was a good choice and now it is fixed. Thank you all for your help and advice.
God Bless,
DKO
-
Called Twin Fountains RV park in OKC this morning to make reservations for Sept. 27 thru Sept. 29. No problem with that time period.
Did learn the following;
There is a Newmar rally starting Oct 1, 2012.At this time there is no problem with having our group in one area. I went ahead and asked Barbara to block out 15 sites in one location at the park. Close to the main building if rain should be in the forecast.
Our group will be known as the 3 Amigo’s rally and Barbara has coded the 15 sites ” 3 Amigo’s “. Credit card to hold reservation at this time. Payment or card process at time of arrival.
Please call to hold your spot ASAP. ( hope I didn’t step on anyones toes doing the above set up )
3 Amigo’s rally….. 405-475-5514 or 866-693-1469
AL
-
Unless there is a strong reason for not running a generator I seriously doubt the investment in solar panels will yield enough benefits to justify all that is required to install them and unless you are willing to sacrifice the luxury of the conversion.
Our coaches are energy consumers. That is not a criticism, but an acknowledgement that when they were converted energy conservation was not the prime motivation for the system designs. We have large house size refrigerators, energy consuming lighting, and a lot of “key off” loads, ranging from clocks, alarms, inverters, TVs, water pump, etc. But to live comfortably, except on rare days, we are going to run our ACs or our heat sources. Those heating and cooling systems are going to dictate shore power, or the use of a generator.
So solar panels may work well for maintaining our batteries as long as the coach is put to sleep and all switches are off, but to expect solar panels to help us avoid running a generator while we live in a coach might be a stretch unless willing to live as though the coach is nothing more than a metal pup tent. Most of us have worked too hard to be able to afford a coach that lets us live in luxury when away from home, and our generators are likely not going to be worn out in service by motor home conversions.
-
The previous owner of our H3-40 had six solar panels installed on the roof. I have not had the time yet to checked to see if they work or how they are hooked up. They would dry camp all winter in the Keys so the reason for the panels. Hopefully I will get it checked out soon!
-
Tom
I believe if you go to the Alcoa, etc. (whatever company made you wheels) website, it will tell you what to torque your wheels to and what amount of thread must show beyond the nut. The solutions presented so far, while solving your problem and given in good faith, I believe would be found to be unsafe by any manufacture that would surely be called in to testify at a court proceeding where your studs failed and the wheel flew across the road to injury someone or your coach manunvered after the studs failed in such as way as to cause a wreck with another vehicle. There is only one safe way to fix this, that is stud extension. Longer studs are available from many truck centers, I know because I just installed aluminum wheels on my coach which I am converting from an OTR bus to a MH. My coach orignally came with steel wheels. The thickness of the steel wheels compared to the aluminum is much less for the steel, necessitating a change of the studs by the local tire shop that installed my new tires and new aluminum wheels. The studs were not cheap at $60 per stud installed but when finished, it is done right with a torque of 550 ft/lbs and 4 threads showing, which is what my aluminum wheels call for from the manufacture.
Keep looking until you find a truck tire center that has access to longer studs. BTW, if you removed your wheels you would find the studs screw through the hub and then have nuts on the back that lock them (the studs) to the hub. The same amount of threads showing are necessary on the inside of the hub as the outside of the wheel.
HTH
Rob
91 LeMirage XL40
Missouri
-
John,
What comes to mind is has it been recently serviced and if so, could it have been over filled or just not evenly pushed back into place?
The bigger ones like my XL have a really tiny vent hole in the cap to relieve pressure and sometimes that hole needs cleaned out with a needle so it can vent. Maybe someone here with an XLII has knowledge of the smaller cap, but I would think it would also have a vent hole.
I would also assure the wheel is not getting hot causing pressure due to a dragging brake caliper. Once you get it cleaned up and put back together, check the wheel temps after about an hour of driving on each side to see if they’re consistant.
-
Fred,
I don’t believe there is a kit on the market that will fit your application perfectly. Normally, a need must be accurately defined, then a system designed to fill that need. John Palmer of Palmer Energy Systems ( http://www.palmerenergysystems.com/) is an expert at putting together a solar system that will do what you want and teaching you how to use it. He will sell you the components and install it for you or provide as much assistance as necessary should you choose to install it yourself. Staying at his Lake City, Florida paradise is a fun adventure in itself. Give him a call at 941-928-4573 or email him at john@palmerenergysystems.com. -
Jon,
Thanks for your thoughts on this. The brackets do not mount behind the wheel lugs but in front of – see photos where one bracket remains. I have checked with various truck places such as Fleet Tires, in hopes of finding a stud longer than the ones on the bus but no luck. My solution was/is purchasing new lug nuts from Prevost and removing enough material from the exposed face of the nut so as to get the 1/4″ needed.


-
I renewed alll of mine that were not destroyed in the fire.. Had to replace 3. Not a big job all the bores and pistons were perfect showed no scratches or wear patterns. So I just refreshed the O-rings and seals plus a little lube and things are good to go. Suspension test has been on for 3 days and all is good. Bob
-
Pictures of that floated around a year or two ago and anyone that has a Prevost conversion will quickly pick up on a lot of issues that the media either ignores or is not made aware of. Not the least of which is the apparent poor use of space and a design more suited as a party bus than as a motorhome.
I would like to know how much the 40,000 pound weight will increase if it is equipped as our coaches are with the amenities we have come to expect. The interior view shows wide open spaces but what happens to both weight and the CG when it gets equipped with interior walls, washer and dryer, generator, holding tanks, ample batteries, and all the other goodies we accept as normal. It looks slick, but how will it look when it has bay doors, side marker lights, cornering lights, awnings, and access for such silly things as changing tires.
And it is highly likely today’s active converters who already have the technology and knowledge gained of years of experience will agree the development costs for something like that offering all that our coaches offer would be so significant that even at $3,000,000 a copy it would take a long time just to recover the development costs, much less make few bucks on the sale of them.
That thing will get a lot of ink, but it is as likely to become a commercial success as the Edsel.
-
Leak detection often requires cold beer. I need to get some new pictures, but technically my signature is still correct since I have the coach listed.
If you want to play under the bus, are willing to get dirty and greasy, a lot can be accomplished to get you comfortable with how everything works. But a word of warning………I am still a student. The principles are the same, but this bus is different than the older one.