Forum Replies Created

Page 118 of 2304
  • Archived

    Member
    September 17, 2020 at 10:38 pm in reply to: vision

    I have a 2002 XLII Vision for 6 years, 80k miles. Love it, been at Marathon, Colburg OR to have items up graded, positive comments from the technician about the equality of workmanship of the interior.

    Larry & Miriam Nelson

    2002 XLII Visiom

    Envision 2019

    Hurricane, Ut

  • Archived

    Member
    September 17, 2020 at 4:06 pm in reply to: Water Hoses

    I store my ‘extra’ water hoses (three 25′ hoses) behind the front bumper in the storage compartment. I have used them several times but not often.

    My regular water hoses (one for grey water and one for fresh water) are in the second bay driver’s side where I keep the tub for the sewer hose. I keep the hoses separate, drain them and screw the ends together so no water will leak out.

    Liberty also supplies sewer hoses in the built-in stainless steel sewer hose container in the water bay (5th bay driver’s side). I only use those hoses if the sewer dump is further than my back bumper as they reach further. Otherwise, I like my RhinoFLEX hose for regular use.

    I haven’t put anything in the storage box at the passenger side engine compartment. That area obviously gets hot from the engine so I haven’t needed it for storage yet. There is a plastic shield below that area as my Macerator connector is located there too.

    My batteries (3 Lithium) are located in the 4th bay driver’s side with the 4 inverters. The Espar is above the drive/tag axles on the driver’s side.

    Safe travels,
    Mark

  • Archived

    Member
    September 17, 2020 at 3:42 pm in reply to: Water Hoses

    This is not intended to start a fight, but it needs to be in context.

    Liberty has a nice stainless steel box with a hinged door bolted above the chassis batteries accessible via the passenger side engine door. It has compartments separated so you can store the water hose(s) and two sections of sewer hose. There is enough room in the top section for me to also store all my spare belts. The box is ventilated via louvers so if a hose drains water it will dry out.

    This is a good and convenient idea because the way my XLII is set up that space is open. I do not know if other converters have that space open or if H models have space in that area.

    If you do a search there are all kinds and sizes of aluminum boxes and drawer units that would be ideal for hose storage or even storage of other items like belts. There is a large number of companies making boxes and drawer units of various sizes, mostly for the interiors of utility or service vans.

  • Archived

    Member
    September 17, 2020 at 10:49 am in reply to: Excessive LEAN in curves while interstate driving?

    Billy: I can’t fathom why someone would delete the rear sway bar if that is the standard for that shell. I can’t imagine why Prevost would allow that. I’d look into having that updated.

    Jeff: 10,000 miles is too short of time for good shocks to go bad. I didn’t think to mention sway bars like the smart guys did. (Actually … I’ve become a little sensitive to stealing their thunder.)

    Almost ALL the vehicles we drive today have sway bars (often called “anti-roll bars” because that is their function). But unless you’ve driven a race car, you don’t think about what they are doing for you as you go around a corner.

    The “bar” actually can (should) twist as you go into and through a corner. The terms in racing are “big bar”, “small bar”, “hard bar”, and “soft bar”. A big bar will have little or no twist while a small bar will have quite a bit of twist. Prior to sway bars the manufacturers and racers used stiffer springs to control body roll in the corner. But for a passenger car the stiff springs gave a hard ride. Once sway bars were introduced the springs were softened to improve the ride.

    The big thing set-up in handling for race cars today are: Soft springs (which allows the front to come down and shift weight to the front tires under heavy braking) and a “big bar” (to control the roll as the car enters and goes through the corner), and shocks with little compression resistance (lets the front end drop under heavy braking to shift weight to the front, easier to turn the car) and lots of rebound resistance (keeps the front planted and weight on the front tires as the car goes through the corners). You can see this especially at road courses at the end of a long (fast) straight going into a sharp (slow) corner. The front of the car can drop as much as two to four inches.

    As you go into the turn the first line of defense as Jon said are the shocks, but they will slowly compress and rebound while you’re in the turn and just delay the roll. Almost immediately the sway bar should also come into play to resist the roll, and its resistance should likely be the same throughout the entire corner (unless the engineers have machined it so the resistance is progressive). Then the ride height valves will notice a change and one bag will get air and the other will drop air as the system works hard to maintain ride height.

    I’ve had a occasion to drive a race car with both a small (soft) and a big (hard) bar during the same session, it was swapped out while I sat in the car. The difference was significant. Granted the soft bar should have had stiffer springs, but big bar made the car handle much better.

    For Jeff … I’d have someone look (safely) to ensure the sway bar(s) is(are) properly hooked up, one of the links (dog bones) wasn’t unfastened or broken, or (very unlikely) the bar was broke. If you had that work done 10,000 miles ago, its possible that one of the fasteners has come undone and the bar isn’t doing anything for you.

    I use mechanical locking nuts or Nylok nuts on the fasteners for the sway bars on the race cars. Many guys will use safety wire.

    Only once have I driven a race car with the front sway bar unhooked. It did not end up well. I was so new to driving a race car that I couldn’t feel it was unhooked until it was too late and I was just a passenger along for an unplanned ride into the tire wall.

    I should point out that if all the components of the front suspension of the coach are doing their respective jobs … while the coach is in the corner the outside front steer tire is getting a huge load.

    Jeff, keep us posted.

  • Archived

    Member
    September 17, 2020 at 10:25 am in reply to: Excessive LEAN in curves while interstate driving?

    The ping tanks came with IFS. I believe that is when Prevost switched from the time delay ride height valves to the instant acting ride height valves.

    But the bottom line is if the sway bars and their dog bones are all attached to their required positions then the coach is leaning as normal or there is an issue with ride height valves. All coaches are going to try to lean unless the curve in the road is banked like Daytona racetrack.

  • Archived

    Member
    September 17, 2020 at 10:03 am in reply to: No 12v Power in Coach

    I helped a friend out yesterday, he rents RV’s and sells them too, He’s got a 2007 JaycoSeneca that he sold and new owner was there to pick it up and the generatorwould not run, he said it ran a couple of days ago, So I ask any work has been done lately and he said new house batteries were installed. Traced it down to a black cable coming from gen was a positive cable connected to negative no juice, So the guy he hired to install new batteries was not paying attention, so I wrapped red tape on black cable, you just never know?

  • Archived

    Member
    September 17, 2020 at 7:48 am in reply to: Excessive LEAN in curves while interstate driving?

    If you are speaking of long curves shocks may delay a lean by a few seconds if that, but it is the sway bars that determine how much lean you are going to get.

    I am not familiar with the H enough to be certain, but I think your sway bars are attached at each end with links we have called “dog bones” because they look like dog bones. Within the links are urethane bushings and on my last two coaches they failed and I had to replace the bushings. I doubt if you can fail to notice a bad bushing because they bang and clatter a lot. But if a dog bone got loose or disconnected or its attach point has failed your coach is going to lean because there is nothing to prevent the lean.

    Don’t waste your time or money thinking shocks are going to fix a lean in turns. First verify the sway bars are securely attached and all bushings in place. That is a 1 minute inspection.

    If everything checks OK then the other potential problem is associated with the ride height valves. If your coach leans the valve on the side outside the curve is going to have the lever move to open the valve to deliver air to the air bags on that side to attempt to raise the coach. Conversely on the inside of the curve the lean will cause that side to rise and that will make the air bags on that side get their air dumped to lower the high side. Make sure you are not having air flow to or from the ride height valves restricted in some way.

    If your coach has had moisture accumulate in the accessory system it is possible the ping tanks or air bags have water in them and that will definitely screw up the ability of the ride height valves to keep the bus level side to side. But the collected moisture has to be a lot so that might be a slim possibility.

  • Archived

    Member
    September 16, 2020 at 9:09 pm in reply to: Excessive LEAN in curves while interstate driving?

    10,000 miles since all new shocks and new suspension parts.

  • Archived

    Member
    September 16, 2020 at 7:56 pm in reply to: Excessive LEAN in curves while interstate driving?

    It certainly wouldn’t hurt to bump the Koni’s to at least the middle setting.

    How many miles on the shocks and other suspension updates?

  • Archived

    Member
    September 16, 2020 at 1:43 pm in reply to: Concrete Pad Specifications

    If you’re looking for something to park on, you can use Turf Stone Pavers. Very easy to put into use. I used them to install a drive.

  • Archived

    Member
    September 16, 2020 at 1:34 pm in reply to: 97 Liberty Webasto and Coach Heat Loop diagram?

    My short answer is “I don’t know”. My coach is similar to yours, Webasto on the curbside above the chassis batts. All my valves stay open 24/7/365. Works great, last a long time 🙂 until it doesn’t 🙁

    The 2 ball valves that are unlabeled on your bus are unlabeled on my bus too.

    The 2 ball valves on your bus that are labeled “Webasto In/Out”, on my bus are labeled “Auto Supply/Return” which I guess is for the dash heater core?
    On the street side is a gate vale and a ball valve which I think comes and goes from the Prevost OTR heater core next to the evaporator.
    Call Bill and/or Troy at Liberty, I bet they’ll be able to help. 800-554-9877
  • Archived

    Member
    September 16, 2020 at 11:30 am in reply to: 97 Liberty Webasto and Coach Heat Loop diagram?

    Was hoping Tom might chime in as I think his former ’97 might have been more or less identical given some posts I read, would really like to know what the two ball valves in pic #3 are supposed to isolate and if there are others somewhere else.

  • Archived

    Member
    September 16, 2020 at 9:30 am in reply to: No 12v Power in Coach

    As I said last night on the phone the 50 DN is for the hose only and should not have effected the 12 volt power to the coach.

    The only thing I can think may have happened is they shorted one of the house battery cables when they were re attaching to the back of the 50 DN.

    Those two battery cables go directly to the black box in the battery bay between the two inverters.

    There are a couple of solenoids in there that relay power, check and see if you have 12 volt to either side of the relay.

    The 12 volt power cable on the top left side of the ECC cabinet should have 12 volts. I don’t remember where that cable is going to but I think it is from the relay in the black cabinet in the battery bay.

    Check all the fuses along the bottom of the ECC cabinet, one of the larger fuses should pass power to the mother board.

    I can’t come up with a reason you don’t have ignition power, the 50 DN work should not have affected the coach chassis power at all.

    Also look in the gray elecctrical panel above the engine, there is a solenoid there That is and ignition key source.

    Also check the 12 and 24 volt lugs in the upper cabinet above the steer compartment.

    Also look at the number #34 wire in that location, I think this is your ignition wire to the key switch.

    Just a thought but check the voltages at your Vanner equalizer ad see if you have 12 and 24 volt, this will not affect the house but does proved service to the chassis.

    If I come up with any other ideas I will call you.

    Two guys that would know for sure is Gill Johnson or Miles Circo.

    I don’t have their numbers any more but I think you can find them on POG.

  • Archived

    Member
    September 16, 2020 at 7:39 am in reply to: Stainless Polishing

    His cutting/polishing wheel was about an inch wide and maybe 10 inches in diameter. He was using green polish.

    Some of the scratches were so bad, he had to sand the areas first with sand paper. Once he got a matte finish without scratches, he switched to polish.

    He was very patient and very methodical. Once I thought he was done, he went over the area many more times.

  • Archived

    Member
    September 15, 2020 at 8:42 pm in reply to: Stainless Polishing

    Did you see what kind of polisher he used? I have a grinder with different wheels and bars, not easy, I wonder if he uses a wider wheel?

Page 118 of 2304