Tim
Forum Replies Created
-
WAG… Filter Minder failed or someone added one to the intake and metal shavings from the drilled install went to the turbo.
-
Make sure Prevost is aware of the drains in the hard coolant lines that run under the bus from the gen to the remote radiator. Once these are pulled, it should be unnecessary to drain the radiator (pull the cap to let it drain) but you will still have to drain the block. Pull engine cap again.
-
I was tongue in cheek when I said to disable the water pump because to be consistent we need to check all limit switches or sensors, not only on the generator but the engine also.
If we lack confidence in any of the devices intended to shut down an engine or generator we have a lot of work ahead of us because we not only have to find the limits, we have to test the devices at the limits. To use the high temp generator as an example we have to create a means of heating a liquid to 235 degrees (maybe oil?), have a calibrated gauge to be sure we are in fact at the right temp, and have the device connected to something to signal when the circuit opens or closes.
-
Too Bad looked like a very clean bus. It will be interesting to hear the cause.
-
If the polish has been damaged such as with a scotch brite pad you can use a fine grit wet sand paper if the marks are deep, again getting up to a 1500 or finer grit, then carefully polish using more abrasive rouge working up to a fine rouge for the final polish with great care taken to avoid heat build up on the panel.
The buffs will start out stiffer and more aggressive, but they also will work up to loose buffs for the final polish.
-
Not sure why you have to put a multi-meter on them, I just popped the D/C breaker in my D/C panel to determine they are on the D/C circuit, not the A/C circuit.
But again, this is for my Marathon, and maybe Featherlite’s are set-up different.
-
Jon, I don’t have one to put a meter on. I figured Fred or someone else would know the answer.
-
Since picking up our coach mid November we have been busy doing maintenance and repairs. We really didn’t think it would take as long as it has…but a least we are making progress.
-
Fixing lots of air leaks. I was keeping track of how many air leaks we have fixed but after I got to a certain number it just sounded like an exaggeration in print. Suffice it to say “a lot”. We have replace a lot of air fittings, drain valves, and air line tubing.
-
Replaced the Marathon “AUX” air tank, replaced the pressure switch, replaced air filter for Marathon AUX air system, and rebuilt Norgren filter in the maintenance bay.
-
Rebuilt the generator air bag distribution valve manifold including check valve.
-
Replaced the generator bay ceiling insulation. (no photo)
-
Made and installed a “doggie deflector” for switch panel behind drivers seat.
-
Replaced the bed lift gas springs, pneumatic actuators, and MAC valve for the bed lift. (no photo)
-
Rebuilt the WABCO 1200 air dryer.
-
Replaced the pneumatic actuator for the bathroom door. (no photo)
-
Replaced all 5 pneumatic actuators for the awning windows. (no photo)
-
Replaced the Bendix E-10P foot brake valve.
I believe we are nearing the end of the end of the first round of maintenance items. Looking forward to using the coach and meeting some of you folks.
Thanks all.
-
-
I was helping a friend with his 96 Liberty and he pulled out both of those diodes and 1 of them went to Webasto and it would not run because it was in upside down and the other 1 might of been to circulation pump on Webasto but it has been over a year ago and CRS is kicking in.
-
I live in the Hudson Valley area of NY. I am in the process of purchasing a 2008 XLII-45 Marathon Coach. This year when I left for Florida after the Holidays, it was -2 degrees F and was 17 above in southern VA where I stopped for the night.
Are the bays in these conversions heated by the Wabasto unit sufficiently so I won’t need to worry about the water bay, tanks or liquids being carried below?
Just want to say as a “newbie” (hate that word) to the Prevost Community, the amount of information provided by the members and moderators is staggering and appreciated for someone coming out of a “typical” Class A pusher. I have a lot to learn,
– Ron
-
JR, sorry about the commission 🙂
Good call, will do
-
did you do the MCI? I just redid a 45XLE. wheel base is longer with E. Depends on your needs. If you must do it yourself. Build Kiss===Keep it simple stupid! my conversions. If you must depend on it to live in. For a group duplicate systems. you see 5 ac and two gen sets because you can’t be down if one fails.
-
I’m with you Fred…The more I learn, the dumber I feel. Geo.
-
The best answers to your excellent questions is to go look at other coaches and copy what they have done as far as systems.
I don’t know how you intend to use the coach, but what you will see are ideas you can tailor to your application. The devices and systems you will see are going to be common to a lot of coaches and those system designs have evolved so do not try to be real creative until you actually have experience with those systems.
Reinventing the wheel is an admirable trait, but before you can do that you have to start with an understanding of the wheel you did not invent.
-
I have a customer that didn’t have the correct license in Texas, and when they were broke down on the road the police came, while waiting on the wrecker wrote them a ticket for improper license to operate the coach…