Forum Replies Created

Page 3 of 22
  • steve

    Member
    January 28, 2022 at 6:34 pm in reply to: Prevost embroidery design needed

    I think this might work! Let us know if you need anything else.

    Grin!

  • steve

    Member
    October 7, 2021 at 10:12 am in reply to: Latest Coolant Analysis Report

    Here’s our latest report:

    Our coolant is Prestone Command HD w/SCA Pre-Charged, part# AFC10000. The water filter I initially used was a “blank: Fleetguard # WF2077. Then April of 2019 we installed a Fleetguard “Need Release” # WF2131. This coolant has been in service in our 96 Liberty XL40 for 51 months and 21k miles.

  • steve

    Member
    September 27, 2021 at 3:19 pm in reply to: How wide front door

    Great advice thank you. I find this forum extremely helpful and I appreciate everyone spending time responding to my many questions

    thank you Dr Gary

    Gboya12 @aol.com

  • steve

    Member
    September 19, 2021 at 8:31 am in reply to: flooring

    Texas rv flooring and design is my son. He can take care of you. Rudy- thank you for the kind words.

    ps- we can save you lots of cash vs a dealer

  • steve

    Member
    August 31, 2021 at 1:38 pm in reply to: Engine Oil Residue in Air System

    I wouldn’t necessarily rush to judgement. Air tanks are supposed to be drained periodically (I do mine every 10K but I think the recommended time is more like 6K) to eliminate oil and water condensation. Also, as others have mentioned, the condition of the air dryer is important.

    Sounds like you’re new to the coach so I would check these items out before going for a compressor. I have about 255,000 on my coach and I’ll get several drops of oil out of the first tank every 10,000 when I drain.

    By the way, when I first got my coach it had about 50,000 miles on it and it was 5 years old. When all the air tanks were opened at the same time on a lift, the floor had to be mopped before continuing with service.

  • steve

    Member
    August 26, 2021 at 1:37 pm in reply to: New format

    What print size are you referring too?

  • steve

    Member
    August 26, 2021 at 1:18 pm in reply to: Hydraulic or air jack recommendations

    Al-

    ’97 40′ xl mirage, Nor Cal

  • steve

    Member
    August 26, 2021 at 10:39 am in reply to: Advice on TV service

    Chuck,

    I use a mix of technologies for just the reasons you mention above. I too have been a DirecTV subscriber since just about the inception of the service. I understand they have recently announced a move to rebrand their AT&T TV service as AT&T Streaming. To me this feels like part of a longer term strategy to move all services (both DirecTV Sat based and cable based service) to a strictly streaming service based offering. I don’t know if you have played around with AT&T TV, but the channel line-up is already well lined-up with the DirecTV channel structure. Wouldn’t take much for them to replicate the DirecTV environment on a streaming service and eliminate all together the expensive DirecTV satellite network. I’m also using an AppleTV for streaming and other content.

    Now, that puts a lot of pressure on reliable streaming for those of us on the road. I am using the FMCA plan through Sprint and have been satisfied with the results. Not perfect, but has worked well in the locations I have been in.

    Another promising option is Star-Net (Elon Musk’s satellite based internet). That system is designed for moderate speeds (100-300meg download speeds) with VERY low latency. Not fully commercialized for moving vehicles yet but coming soon.

    For now, I will stick with DirecTV and ride out their strategy and see where that lands. I suspect their big moves (like abandoning satellite network) will be years off. In that time, wireless internet will improve dramatically and will probably take-over.

    I didn’t mention cable based systems available at most RV parks. Many of them are upgrading those systems to HD and are reasonable options. For now, I believe we are in a state of flux that will shake out in the coming years.

  • steve

    Member
    August 25, 2021 at 11:45 pm in reply to: Monthly runtime to keep systems happy?

    Ok, I will only start up when I can take it out on the road for a roll. Probably better for the tires and transmission as well.

    Thanks Dick!

  • steve

    Member
    August 25, 2021 at 10:28 pm in reply to: What are your thoughts about an H3 Prevost

    Thank you for your responses. I did go to the West Palm Beach Florida Prevost Show and I went in and out of at least 20 buses. Also I saw the buses for sale on the Danny Myers lot in Florida. In addition I saw 35 buses Bus For Sale .com and Staley bus. All my questions came after visiting all multiple multiple buses. I spoke to plenty of sales people but it is the Prevost forum that I have the most confidence in

    Prevost forums

    201-663-0935

    thank you Dr Gary

    Gboya12@aol.com

  • steve

    Member
    August 19, 2021 at 11:55 am in reply to: Front windshields

    Chuck yea I have been gone for a while it was a bit more labor intensive than I anticipated but well worth the trouble.

  • steve

    Member
    August 19, 2021 at 11:39 am in reply to: CAN bus troubleshooting on a 2011 Emerald/Outlaw

    Generally there is no need to debug at the CAN bus message level unless you are looking for software bugs. Most CAN bus module problems are power/ground or internal to the module (e.g. driver burn out).

    Here is what I would do. Find the module that operates your lift. Verify power and ground to it. Use a test light or low-Z meter to eliminate phantom voltages. Check output (likely a wire to open/close a solenoid). See if you have output at the module, then check at solenoid.

    If you have power/ground at module but no output, check for CAN bus signal. First, measure resistance of CAN bus hi/low transmission lines. Should be 60 Ohms plugged in, 120 Ohms disconnected on one side. If that is ok, you’ll need to hook up a scope (you can get them for around $100+). With the scope, look at CAN bus signal wave forms. You should see packets with voltages ranging from 2-4 Volts. If the voltages are incorrect or the packages show distortion, one of the modules on the CAN bus has a bad driver (signal output stage) and needs to be replaced.

  • steve

    Member
    August 18, 2021 at 9:51 am in reply to: Hydraulic or air jack recommendations

    I built ramps also, But most of the time I lift the bus with level low system,I bought a couple of 20 ton bottle jacks and I put them under frame,but I screw top of jack as far as it goes and I don’t jack up jack,I use them as jack stands so it can’t drop down and then I can slide under safely. I’m not a Harbor Freight fan but both of my Harbor freight jacks work well 1st one is a air 20 ton bottle jack and 2nd is a low 12 ton bottle jack.

  • steve

    Member
    August 11, 2021 at 11:03 am in reply to: brakes draggin?

    Unless there is a difference in pressure on that passenger tag the higher temp can be a dragging brake or bearing issue.

    Aluminum wheels do a good job of carrying heat so after a good run check wheel temps as close to the hub caps as possible. They should all be nearly the same as long as tire pressures are close to the chart values.

    If you had a recent hub seal replacement on that tag wheel and the bearings were not tightened to spec that could be a cause just like the dragging brake. I do not know the type brakes you have on your coach, but regardless I think both possible types use automatic slack adjusters with the Knorr Bremse adjuster internal to the caliper, or the Meritor on the slack adjuster. Get the weight off the tag tires, release the parking brake and spin them by hand. You will be able to tell if one is dragging.

  • steve

    Member
    July 11, 2021 at 12:01 pm in reply to: Auto overFill

    I no longer own a Royale which utilized this system, so take this with a grain of salt…..

    I set my “ON” point for Auto Fill at 20%. That means it will open the water valve when the tank gets down to 20% full. I set my “off” point at 85%. That means the water valve will close when it gets up to 85%. I would lower the off point in case your tankage system isn’t ever reading 100% full. Never had a problem using that strategy.

    I do know my coach had 1 or 2 small relay boards in the plumbing bay (on the front wall of the bay). These were generic relay boards that can be bought off Amazon for little money. At least one of these (and maybe both) controlled the Auto Fill function. You might start there. I’ll try to find a picture of the board in question. I would think the shutoff valve would either work or not work. If not working, then its the solenoid valve or the control circuit.

    Are your plumbing valves set properly for autofill? I don’t remember the sequence, but remember there is a setting for autofill.

Page 3 of 22