Forum Replies Created

Page 2 of 15
  • Michael

    Member
    April 17, 2020 at 11:13 pm in reply to: Amana fridge

    For a labor cost of 3500 to install new fridge I can make mine as good as new with all new parts for less than half of that, that’s why I’m on the fence as to replace. I just can’t justify paying 3500 for install plus the cost of fridge that’s almost 5k

  • Michael

    Member
    April 3, 2020 at 11:13 pm in reply to: Prevost liberty solenoids

    Anthem: are you replacing parts, pieces, and components? Or are you re-engineering the electrical system Liberty originally installed in the coach?

  • Michael

    Member
    March 17, 2020 at 11:08 pm in reply to: Oysterfest – Yes or No

    I have heard rumors that if things get worse they will consider closing highways to tourist resorts such as beaches etc..They have already closed the highway into the Outer Banks in NC I believe… want to go but only if things simmer down and some restaurants re-open in the area.

    Be safe everyone !!

    Diane

  • Michael

    Member
    March 16, 2020 at 10:30 pm in reply to: Leaving Florida

    WHERE ARE YOU LEAVING FROM?

  • Michael

    Member
    March 13, 2020 at 6:31 pm in reply to: Another radiator leak!

    Well we finally met up with the Karths in Las Cruces, funny thing though, Dick looked like he has lost a considerable amount of weight. Seems to have come from his wallet.

  • Michael

    Member
    February 18, 2020 at 10:05 pm in reply to: Air leak with power switch

    Jeez A1 I needed a laugh on my way to bed.

    Good night

  • Michael

    Member
    December 20, 2019 at 4:05 pm in reply to: I-95 this week

    For the life of me I cannot figure out if this guy is a moron because he is parked half on the shoulder and half in the road, or if he is a moron for driving like that and by driving on the shoulder he thinks his slide room is not going to get hit.

  • Michael

    Member
    May 25, 2019 at 4:51 pm in reply to: But For The Grace Of God go I

    Very well said and may GOD BLESS AMERICA and all that serve this GREAT COUNTRY!!

  • Michael

    Member
    April 4, 2019 at 9:43 am in reply to: Knobs,What do they do?

    For the few problems I have I like my 97. It’s not to complicated.

  • Michael

    Member
    April 2, 2019 at 9:08 pm in reply to: 1998 Country Coach

    Very, very nice.

    Got an MSRP?

  • Michael

    Member
    February 19, 2019 at 11:54 pm in reply to: XLII Buyers Beware

    Mira Loma quoted me today, just the rivet kit with patch panel alone installed was $27,000. This just repair, no paint. The coach we are looking at has no paint on stainless. If all the panels need replacing, we are checking into a whole matte finish on the bus.

  • Michael

    Member
    February 19, 2019 at 1:38 am in reply to: XLII Buyers Beware

    I had similar leak. I recaulked with black caulk the drip rail that is located a few inches above the door. Caulk the top edge of the drip rail. This worked for me and leak stopped.

  • Michael

    Member
    February 16, 2019 at 8:54 pm in reply to: Cranked With The Key But Started Only From Back

    I cranked and ran the bus 80 miles today and it did fine. The drive was one hour and forty five minutes and the total run time was about two hours and thirty minutes. My moves the next two weekends will be relatively short again. I am hoping this is behind me, but not super confident. I am open to any ideas.

    I did finally get the bus washed. The back had a few thousand miles of road grime and all the greasy finger and palm prints from the repair. It was a mess. I never put soap on the sides, except for the tires and wheels and maybe one other time on the back. This one required soap and scrubbing.

    Better

    Davy

  • Michael

    Member
    February 14, 2019 at 12:02 am in reply to: Cancer Donation – Leon Snyder – Marathon Coach

    God bless his family and friends.

    Davy

  • Michael

    Member
    February 8, 2019 at 11:04 pm in reply to: Inject Resp Time Long

    The Diagnosis and Repair

    Friday morning at Prevost I met with Chris the Service Manager. He told me that he had called Mid Coast Diesel that does most of their Detroit work. As you know, Prevost has not used Detroit engines for at least 8-9 years so they no longer train their guys on Detroits or keep their computers updated with the lastest licensed Detroit software.

    A Prevost mechanic did try to access the codes on the engine computer but it was a no go. Mid Coast said it would be Monday before they could get there so we loaded up some clothes and gear and drove 80 miles to Sweeny, Texas where we were beginning services that night.

    Monday morning Mark from Mid Coast Diesel came to Prevost Houston and hooked the computer to the BoggsMobile. The bus computer was showing the code that corresponded with the alert the Detroit Diesel Monitor had given me when the bus quit Thursday night, Inject Resp Time Long. He began heavily leaning toward the wiring harness, but he looked diligently for other causes too.

    After he cleared the codes, cleaned some grounds and cleaned some of the wiring harness plugs, he asked me to crank the bus and it started. Yay! In a few minutes, it was purring like a kitten. He checked all the fuel injectors and all was well on the computer. After running for nearly an hour he went back to the engine and started messing with wires. When he pressed the wires on the wiring harness from the computer to the fuel injectors, the engine almost died. Bingo!

    He had duplicated what the computer was telling him and that is a positive thing. We would not want to go through the expense and hassle of replacing the harness without some confirmation.

    While he was telling his bosses to locate a new harness I set about clearing out from under the bed to see if the engine could be accessed from the floor. After several hours and several people looking it over, it was determined to be a no go. If I was somewhere more familiar with conversions, it might could have been done, but not at Prevost Houston. Pulling the engine was going to be a better option. I can not even believe I am saying that pulling the engine was going to be better.😓

    A plan was set in motion over the next few minutes. Prevost would pull the engine and put it back in. Mid Coast would do the engine work.

    I had some decisions to make by the next day. Mid Coast recommended I change the fuel injectors while the engine was open since I had 350,266 miles on the bus. The original ones were working fine, but if one went out 6 months from now, all the work that was being done would have to be duplicated.

    I have a hard time making a decision like that and I certainly did not know what was best. My wife reminded me of our family policy. When we do not know what to do, we go with the advice of the person we trust that has some level of expertise in that specific area. Jeff Rowe is that guy for us and he said with the mileage and age, he would lean toward replacing the injectors.

    I trust Jeff, not only because he knows much more than me, but he also understands quite a bit about where we are in the grand scheme of things. He knew without me telling him that this repair was going to stretch us beyond our limits and he would not recommend something just to hear himself talk. Decision made.

    Prevost did not want to remove the engine without the parts and Mid Coast did not have the parts in hand until Wednesday. They pushed the bus into the shop Wednesday afternoon the sixth day after the breakdown. Thursday morning Henry from Prevost began taking out the engine in earnest. I liked Henry immediately.

    Friday morning Meho from Mid Coast was there to tear into the project. I like him too.

    The old wiring harness

    The $332.13 replacement.

    Three of the new injectors in.

    Rocker arms back on and valves being adjusted.

    The new wiring harness in.

    Meho finished up that same day, Friday, and by Tuesday afternoon Henry had the engine in and ready to crank. That is when he discovered the oil gusher Jeff told you about.

    You can see the inside of the engine underneath the gray gasket in the picture below. That gap was about 8-10 inches long and there was a smaller one on the other side of the engine.

    Meho came Wednesday morning, February 6 to program the injector numbers into the computer and to check the oil leak. He loosened the rocker cover bolts and tightened them several times, but he could not close the gap. To everyone’s disappointment, it was obvious the engine had to come back out.

    Meho called his boss to tell him the news and that he thought he should stay and help with the removal, fix the problem and help with the insertion. His boss agreed and so did Chris from Prevost.

    About one hour and fifty minutes later, the engine was out and the valve cover was removed. Wow!

    The troubleshooting begins.

    Meho tried a new gasket, the second, but the rocker cover would not seat properly. Then he began to suspect the rocker cover was warped. The old gasket would seat properly so the new gaskets were examined carefully.
    After repeatedly going over everything that had been changed, he eventually hit on the culprit. The bolts that secure the rocker cover have a bushing. He had changed them per his normal procedure. Once he compared the new bushings and the old bushings, he discovered the new ones were slightly shorter.
    The part number on the new bushings was the correct match for the serial number on my engine, but they were not the correct part. It was an honest mistake, but not one that Meho is likely to make again. He had checked the tightness of the gasket to the engine at the ends around the cams and it was good. He assumed the rest was good. I am in no way disparaging Meho or Mid Coast. An honest mistake was made and they rose to the occasion. I would not hesitate one moment to have Meho work on anything I have. He is knowledgable, skillful and has a great work ethic and attitude.
    I thought I took a picture of the bolt and bushing, but I can not find one. These are similar bushings from the Internet.
    The sleeve of the bolt is designed to bottom out and the bushing holds the rocker cover tight against the gasket and the motor. The shorter bushing allowed the bolt to bottom out without pressing the bushing against the cover. Problem found and solved.
    They pushed the motor back in at 1:21 on Wednesday and began to hook it up. They cranked it at 3:00, one hour and forty minutes later. Wow again!
    I could have test driven it then, but Houston rush hour was heating up and I decided to drive it the next day. They also needed to replace the temperature sensor on the transmission fluid and that would not be in until first thing Thursday.
    Thursday morning I brought my family and all of our gear and loaded up in the bus. We test drove it 42 miles and all was good. We hooked up the car and headed east. Very glad to be leaving Texas at last.
    The rest of the story is next.
    Davy
Page 2 of 15