Jon
Forum Replies Created
-
-
When mine went I considered replacing with a different VR. Power Tech insisted theirs was different and superior to any others so I spent the money and purchased Power Tech’s. That one lasted less than 150 Hrs. I did purchase the 2nd VR from Power Tech too. If this one gives up to soon then I will be purchasing another brand.
Chuck
-
I had a meeting yesterday with our municipality’s building inspector/zoning guy. What a light dimming experience that was.
Keep in mind we’re “in town” on city sewer and water in an area with “single family residential” zoning; not out in the country on five acres or in the industrial park.
Per the zoning we have the following restrictions:
1. “Accessory buildings” which are defined as attached/detached garages, sheds, and boat houses (we’re on the river) cannot exceed 1200sf in total. (Do the math. We already have a large 2 car garage.)
2. The height of any “accessory buildings” (as defined above) cannot be higher than living space of the residence. Current house is a single story structure with a 5/12 pitch.
3. Side yard for paved parking or patios: 5′.
So … no bus barn at the house. Another parking pad for the coach (w/FHUs) and probably enclosed race trailer is the option.
And maybe “Plan B” … building some large storage, business, RV parking buildings on commercial/industrial land in town.
Shawano isn’t a high end, exclusive community. Its a “normal” community of about 10,000 people 40 or 45 miles from the nearest big towns: Green Bay or Appleton.
Thanks for all the suggestions and information. Hopefully this new category will serve as a place for members to post their bus barns and get their bus barns questions answers,
-
Looks like a check valve. Does move open freely or is is stuck?
-
Well…..This isn’t exactly like my old PT generator, but I suspect it’s a radiator air drain. My generator was notorious for air in the cooling system which needed to be purged occasionally. I suspect you get her hot, then open up the valve and purge any air that is in the system.
-
Thanks Jon.
Im am pretty sure that this is the replacement for the switch I currently have. I would say that it is a direct replacement. I have seen the back of mine when we installed the new inverters. This appears to be exactly the same without taking it back out.
https://www.bluesea.com/products/9077/AC_Rotary_Switch_-_OFF_%2B_3_Positions_240V_AC_65A
Jon I may need a loan though if that is my problem! lol
I did notice a small fuel line leak in this process. I am not sure if that could have been causing enough of a drop in generator power to be causing this issue or not. I should know soon, as I have had everything back up and running for about 20 minutes now.
-
Well Done Dave, I like the easy solutions.
-
I think I figured out the problem. I put a 12 volt charger on each different 12 volt bank and charged the batteries up full. Now the LCD screen on the left side of the steering wheel reads 12.9 volts with out the charger on. I ordered a Guest charger with 2 outputs and 5 amp charging. It will arrive Tuesday and be installed.
Thank you for all the advise
Dave
-
You knew very well I was purchasing all the parts and getting ready to fly down there. Here’s my last text to Mr. Duarte
-
Ben,
I am very sorry to hear of this experience. Jessica and I try very hard to verify what is posted here in the forums. My initial thought was to possibly delete this post as we cannot verify all of the facts. With that being said I appreciate the professionalism and the time that you spent to worn others. We will leave the post stand as is, at this point.
Mr. Duarte if you would like to respond here or to me directly, I welcome you to do so.
You are correct Ben. I have been involved in premium coaches for over 10 years and I can honestly say that I have not heard a story to this level. We are very fortunate that a very high percentage of Prevost businesses and enthusiasts seem to be some of the best people that I have met. Just over the last 2 weekends Jessica and I have met many and spent time with many old friends and I can say that we thoroughly enjoyed the time spent with all.
May I ask for the city that this coach is supposedly located? Please do not give the full address.
Please keep taking a look in our classified section. Listings have been changing almost daily. We have tried hard over the last several months to improve this area of the site. The results have been very promising and the amount of listing and sales are up substantially. If we can assist you at all with making a direct contact with a seller, please do not hesitate to ask.
Again sorry for this very rare experience in our industry. I hope that maybe you will reach some type of satisfactory resolution.
Bill III
-
Thank you, after going thru this process, it’s not really that bad of a job. The alternator is heavy, but with a little planning was very doable. I do have a couple comments that were questions of mine before I started. One was this notion of requiring a special tool to install a 50DN. I was unable to locate any information on this, and after looking at how the 50DN interfaces with the cam gear and flywheel housing on the back of the engine, I am not sure why you would need a tool or what it does. The 50DN has a large locating ring that centers the alternator with the cam gear. The other comment i had regarding a term i have seen around online and which Prevost corrected me on is “oil cooled”. Prevost told me the Alternator in my bus is air cooled, Oil lubricated, now that may have changed on the newer models, but mine was oil lubricated. To lubricate the Alternator there is a very small line that comes from the engine block, (oil filter housing area) that lubricates the 2 sets of tapered roller bearings internally. This oil is engine oil and it feeds in the top, runs into the roller bearings, and gravity takes it out the front to lubricate the drive gear, then back to the oil pan. I now have more room to work in this area if the need arises, and will be installing a belt driven alternator to charge my house batteries in the near future.
-
This one likes to stand on the horn while we are at Walmart
-
Luc, maybe it’s your equalizer? Follow the test instructions on p.12 of this pdf: https://vanner.com/manuals/EQUALIZER-60-SERIES.pdf
-
Jon
MemberFebruary 23, 2022 at 2:42 pm in reply to: Charging 24V Chassis Batteries With 12V ChargerOur Liberty has a dedicated 120VAC circuit/breaker with receptacle on the roof of the engine bay for charging the chassis batteries. In 1999 Liberty installed a massive 24volt DC charger and hardwired it to the Vanner (I think, maybe the Isolator?) on the roof of engine bay plugging it into the above referenced receptacle. For 1999 it was probably high tech, but Jeff Rowe at ETLC told me to get rid of it as it was a dumb charger and could overcharge, damage the chassis batteries, and boil them out.
A year after buying our coach in 2014 I replaced the big charger with a Guest/Marinco charger and hardwired it into the chassis batteries. I don’t leave it on all the time. If the coach has sat for a month or more, before starting the coach I’ll turn the key to “ON” and check the “Engine Voltage” on the dash gauge. If I don’t have at least 24.5 volt DC, I’ll turn on the “24 Volt Charger” breaker on the main panel to bring the chassis batteries up further and then fire up the Detroit. Sometimes I might leave the outside lights on overnight and drain the chassis batteries and need to bring them back up.
I’m reluctant to leave the Guest/Marinco charger on all the time as I think it would mask a battery going bad and suddenly be so bad that I can’t charge the chassis batteries or start the coach (BTDT!). I’ve found that the chassis batteries “stay up” for a long time if I don’t leave “something on”.
There are other alternatives to the Guest/Marinco chargers that other Prevost owners have used. I like the idea of having the charger hardwired on a main panel breaker. Easy to turn on and off. Don’t have to drag out a charger hook it up during inclement weather.
Somewhere I have a wiring diagram that I used and if I can find it, I’ll post it.
https://www.marinco.com/en/p/2720A/Guest-On-Board-Btery-Charger-20A
-
’96 XL
Here are some photos. Also, I tried hooking the single 12 volt charger directly to the Vanner. Red to 24volt, Black to 12 volt. 3 hours later the SOC had not changed. I’m wondering why not hook the Red lead to the 12volt connection and the Black lead to the common ground, as that would seem a complete circuit.
The batteries do charge when I use the two 12 volt chargers method.
According to the diagram, the batteries look like they are hooked up correctly. There are a couple extra leads.