Forum Replies Created

Page 5 of 19
  • Glenn

    Member
    December 10, 2014 at 12:18 pm in reply to: Auxiliary air leak

    Based on my own experience when I went 100% after air leaks.

    My number one item to replace is the check valve leading outbound from the AUX compressor. It should be on the list of items replaced on time in service. If you have a leak from AUX intake it’s the AUX check valve.

    This check valve is easy to replace and cost under $20 available at Grainger. Several things are available through other venders if you wish to buy a custom made check valve.

    I had own built with a suggested “cracking pressure” if your in the valve business this is a operating term. Suggested my custom valve be 5 psi cracking pressure. So 5psi cracking pressure (air) is needed from your air compressor to open the valve. Another change was the valve surface be coated or made with “viton”. This superior material is preferred as it will operated in heat/water conditions up to 400 degs.

    Again heat and water are the enemy in check valves. Marathon installs there valves right out of the Thomas Compressor. Not the best location for a check valve but with a change out every 2 years you will be ahead of the leak game.

    After my air leak adventure the Marathon AUX compressor ran once in 5 days when sitting at idle. Getting lots of other leaks fixed I spent around $1000. Another item is the air operated toilet. That story is complete book in itself and posted in the plumbing section.

    Another item and near the top of the list is the brass wheel drain valve at the bottom of AUX reserve tank under driver. Get rid of it ASAP it’s leaking now or will shortly. Poor design, not a good choice as it has to be in nearly new condition to work properly, seating of valve is the issue. Replaced with a regular gate valve this style will not leak for years in service.

    Check valve is the first piece of brass at 9 o’clock position from gray block.

    Check valve removed above. Can be easily confused as a common pipe fitting. Usually stamped with an arrow showing direction flow. Be sure you check direction flow prior to install. If you get wrong you’ll be taking it apart again to reverse.

    New reliable drain valve

    Picture of wheel valve…..get rid of this valve…… the seal is the problem, just add water.

  • Glenn

    Member
    December 10, 2014 at 11:16 am in reply to: Oyster Fest 2015 – A No Rally, Rally

    Courtney at Bella Terra said we have 13 coaches signed up so far !! Yay !!

  • Glenn

    Member
    December 9, 2014 at 10:15 pm in reply to: Buying a Prevost

    I second Jon’s comments. Not just because he was one of the Prevost owners whose experience, expertise, and knowledge I relied on when we bought our Prevost in April of this year … but because I’ve found what he says to be very accurate.

    New tires and new batteries will run right around $10,000.

    Zeroing out all the stuff that has a limited life is around $20,000. Our 15 year old coach had literally no maintenace records other than some history I dug up on some fluid changes over the last five or so years. So the presumption was that break chambers, Norgren valves, air bags, etc. etc. etc. all need to be replaced which I had Jeff Rowe at Eastern Tennessee Luxury Coach do for us along with the tires and batteries.

    As time goes on I’m expecting to replace some fluid lines that are more than 15 years old, probably dried out, and will eventually crack. Other small things will fail and need replacing. Right now I am reading the articles on refrigerator replacement with great interest as I know ours won’t last forever.

    We hope this helps. Are you planning on attending the All Prevost Show in Tampa during early January? We were there in 2012 and learned quite a bit. Good luck with your search.

  • Glenn

    Member
    December 9, 2014 at 9:09 pm in reply to: Setting the overhead on a Series 60 Detroit

    Jon, I think you are correct as I thought I read somewhere you can turn the engine over as you describe. Luckily all my coolant hoses are in good shape, a few small ones I have already replaced.

    I had a very small drip from the big hose going into back side of radiator, I was able to get down and tighten that one up via the top acess panel, no other way to get to it that I know of!

    I did replace both belt tentioning bags right after I set the valves and I think I got a bit more access by removing the bumper…anyways bumper comes off very easy, just 6 bolts if I recall with the air ratchet.

    The more I read and learn about the Series 60 the more I like it, they have an incredible reputation for mpg and reliability. Lotta mechanics on truckers forums say they will also tolerate a lot of abuse.

  • Glenn

    Member
    December 9, 2014 at 9:02 pm in reply to: Setting the overhead on a Series 60 Detroit

    Yeah I will try and download that PDF creator and do a lil more detailed write up…I should have taken some more photos but was kinda focused on getting it done.

    It is also worth mentioning that ALL of my valves were on the tight side, nothing out of spec but close. ALL my injectors were also off spec and required adjustment.

    I think when I started out I was checking the adjustment to see where things were at then when I noticed most were off just went about setting them all fresh. I think maybe a couple were outside of the spec all together.

    If anyone wants to borrow the 82.1mm injector height tool just let me know.

  • Glenn

    Member
    December 9, 2014 at 7:25 pm in reply to: Setting the overhead on a Series 60 Detroit

    Great job G-man, both the actual work and the great job documenting it.

    Two comments……you can turn the engine over by hand using the pulley above and to the left of the harmonic balancer. You do not have to pull the bumper. I think it takes a 1 3/8 socket. (I’m guessing).

    I saw the small coolant line going to the top of the coolant pipe to the left of the engine. If you haven’t done so check all three of those small lines coming from the reservoir tank. They have aged very quickly and they snap easily due to being brittle. A local hose shop can remake them if they are the type that hardens and breaks.

  • Glenn

    Member
    December 9, 2014 at 1:52 pm in reply to: Auxiliary air leak

    I’ve been to Houston with leaks a couple times. Also to Ft Worth a few trips. Head to Jeffs if you want it fixed. I haven’t been to Jeff’s but that’s where I will take mine next.

  • Glenn

    Member
    December 8, 2014 at 9:28 pm in reply to: Amana Strikes Again

    Glad all went well with the R&R. You’ll sleep well tonight having that change out behind you.

  • Glenn

    Member
    December 2, 2014 at 6:45 am in reply to: Fuel Getting Better

    I really hate to admit this but Tom has zeroed in on a sore subject with his comments about stupid people at 70 and at 10 MPH.

    One of the reasons for my 62 MPH speed is almost all the drivers are going faster than that. The significance of being the slowest vehicle on the road is I am just cruising along and what the others do with respect to lane changes, speed, lane blocking, etc. has little or no impact on me. If I need confirmation of that all I have to do is adjust speed to the flow of traffic to see how it affects me. With the car nearing completion in Cookeville I am now making frequent 120 mile (240 round trip) trips and in my cars I want to go with the flow or even a little faster.

    The stupid people block the passing lane by sitting along side the car in the slow lane. The ones in the slow lane will often jump into my lane but going slower than me just so they don’t get stuck behind someone going slow in their lane. Even if I am exceeding the speed limit there is always a fool that is going to run up on my bumper. The car I drive DOES impact how others drive. Nobody ever will try to intimidate me when I am in the Corvette. The Mercedes seems to invite the rednecks to tailgate even well over the limit.

    It is getting to be less fun driving. I have learned to zone out and let the idiots do what they want to do. But like Tom points out the jerks that change lanes and try to get ahead of everyone really make heavy traffic a bad situation because far to often they steal our safe stopping distance and then it is no longer relaxing to drive, but a stress filled contest.

    But sometimes there is justice. I was passing a line of traffic the other day and a big pickup truck ran right up my tail fast. He was just a few feet away from my bumper and I was 10 over the speed limit. When I cleared the car at the front of the line in the slow lane he couldn’t wait for me to get ahead enough so I wasn’t cutting the guy off. He cut the guy off and passed on my right. Even at 10 over the limit I got the finger for not getting out of this guy’s way. But a couple of miles ahead there he was on the shoulder and the cop was just about to greet him. He was so intent on speeding ahead of me he likely failed to see the cop. I took the opportunity to give a few loud toots on the horn along with a big wave. There is justice.

  • Glenn

    Member
    November 22, 2014 at 10:30 pm in reply to: Webasto parts

    East tenn luxury Coach fixed my webasto problem Go see Jeff. It’s too cold not to.

  • Glenn

    Member
    November 18, 2014 at 12:29 am in reply to: Surge Guard Protector

    Al,

    Glad to hear you made it home and have your rig back in the barn…. Your might be differnet but I asked Marathon about surge protection and pressure regulator when I went in for my first service and they indicated to me that neither device was needed externally. Both were built into the bus. They told me if I see 4 green LEDs at the main breaker it was safe to “turn on” the bus via the main breaker if…If I don’t see 4 green don’t turn on the main breaker.

    So it might be worth asking leon.

  • Glenn

    Member
    November 17, 2014 at 11:58 pm in reply to: Hot / fresh water leak in water bay !

    I am not familiar with the aquahot, a lil but not sure its advantage over the Atwood. Plenty of hot water, can heat it off the webasto or engine going down the road. Easy to replace.

    Well I still have no water with full fresh tank after 24 hours so think it was coming from the lower hot water heater tank, found what could be some pin hole leaks and cleaned them up and epoxied, so will see how it holds up, if it stop will put a new water heater on the list for later this winter.

  • Glenn

    Member
    November 17, 2014 at 10:43 pm in reply to: Prevost Prouds Rally Nashville May 2015

    Do you have to be a member of the Prevost Prouds to join the rally?

    Still learning about all the groups. I’ve heard of POG but not PP.

    The timing just might work for us.

    Mark

  • Glenn

    Member
    November 17, 2014 at 10:36 am in reply to: Hot / fresh water leak in water bay !

    Your pump cycling may be due to your very tiny leak. I just replaced my Headhunter pump because I had a tiny leak in the plumbing, a leak so small that the drip would evaporate before I could even find it. Since mine is all hard piped to the pump, I changed out the pump as a PM.

    The heaters are not all that expensive, about 3500 and not sure if you could just replace the tank. I would change them both out if you’re going to do any. A bad check valve would also allow your water pressure to drop.

  • Glenn

    Member
    November 17, 2014 at 10:18 am in reply to: Hot / fresh water leak in water bay !

    Tom, I will post some pictures later. Have pulled apart alot of the drivers side, all dry, my plumbing is relatively simple on this 40 footer.

    The water has all been in the same area, I suspect the hot water tank, and as of this morning the bay is dry with the hot water heaters removed and the fresh tank at 100%.

    My setup is slightly different than yours but I think I have evrything pulled apart enough that I can see all lines and detect any leak.

    I still have the issue where my pump will run about every four or five hours for 5 seconds to top off the pressure, have found no leak anywhere else in house so I think this is the pump losing a little prime or possibly related to my leak now but not 100% positive on this.

    I do believe it has been leaking for sometime however in warm weather it is so hot in the water bay the water just evaporated as the leak is so tiny.

    Any idea if you can replace just the water tank on the Atwood or do you need to buy a whole new assembly?

Page 5 of 19