Forum Replies Created

Page 52 of 214
  • Dick

    Member
    March 5, 2020 at 10:25 am in reply to: Looking for a coach,1997-2000

    “That stuff should be bagged and put on my garden” . Ha! Very well phrased and diplomatic. I may be using that one in the future. The iron fist in the velvet manure sack.

    I’m just beating the bushes to try and find a coach both my wife and I can agree on. Have physically looked at over a half dozen in the last few weeks, from California to Arizona and yes, seen a few described as “pristine” that were not, both from private parties and dealers.

    We’ll find the one…the hunt; it’s all part of the grand pageantry of life.

    Thanks all…

  • Dick

    Member
    March 4, 2020 at 7:59 pm in reply to: Lithium Ion Drop in Batteries

    Roger, don’t listen to all of Jon’s BS, he is doing advertising for Tom.

    He had enough balance due him from his share of the PC dues that Tom gave him the batteries.

    Maybe you need to get on board and talk highly about the Pressure Pro system and maybe Tom will give you one.

  • Dick

    Member
    March 4, 2020 at 6:16 pm in reply to: Detroit Allison service

    Good evening,

    We talked with Lewis at Expert Transmission and he’s going to come to us and diagnose.

    I’ll keep you posted when we get done.

    Thanks again,

    Chris

  • Dick

    Member
    March 4, 2020 at 5:49 pm in reply to: Lithium Ion Drop in Batteries

    Jon was extremely diligent in researching all the pieces to this puzzle and his install went without a hitch. As you’re probably aware, his Liberty is 24 volt, so for someone with a 12 volt coach, it’s even easier with battery choices. Relion was also very helpful with our questions. Like Jon said, it’s not for everybody, but it’s coming folks.

    Now for some self pro motion, I’m your Relion guy, so if you want to go down the Litium path, contact me for pricing.

  • Dick

    Member
    March 4, 2020 at 7:45 am in reply to: TSD loses Pilot discount

    I can hardly wait to go to Pilot/FlyingJ to get the 10 cent discount provided by Good Sam membership.

  • Dick

    Member
    March 3, 2020 at 10:12 pm in reply to: Fuel filters?

    Does any one have the cross over for the secondary fuel filter Detroit # 23530645 To the Napa Gold fuel filter

  • Dick

    Member
    March 3, 2020 at 9:07 pm in reply to: Another radiator leak!

    Dick,

    Thanks for taking the time to keep us all apprised of your “journey”. We all benefit from the experiences of others and it gives us more insight when we are getting ready to set off on a trip.

    Much appreciation,

    Doug

  • Dick

    Member
    March 3, 2020 at 9:06 pm in reply to: HID TO LED

    Thanks for the info!

  • Dick

    Member
    March 3, 2020 at 6:43 pm in reply to: Recommendation for air system parts

    Use Swagelok fittings. Highly recommended by the guys in the know.

  • Dick

    Member
    March 3, 2020 at 6:36 pm in reply to: Fuel filters?

    In the absence of any data showing otherwise I have primarily used Baldwin, or if out of stock used Donaldson. Both from Truck-Pro.

    I have used NAPA, Detroit, and Wix over the years, but to me they are generic so I usually just get what is on the shelf at Truck-Pro.

  • Dick

    Member
    March 3, 2020 at 7:15 am in reply to: Another radiator leak!

    I cannot remember exactly how the fan clutch mount travel is limited beyond the 3 drive belts from the engine. Obviously as long as the belts are in one piece the fan and clutch cannot strike the radiator. But there needs to be a mechanical stop so that in the event of a belt failure the pivoting assembly travel is limited to prevent contact.

    Look carefully for that mechanical stop, and if necessary adjust or modify it so there is no potential for the fan or clutch to hit the radiator. Keep in mind the fan, when engaged, is moving a huge amount of air so it is pulling very hard against the belts and if they should fail that force is literally going to pull the fan and clutch toward and possibly into the radiator. Metal flexes so insure there is ample space between the clutch, fan and radiator with the belts removed.

  • Dick

    Member
    March 2, 2020 at 11:37 pm in reply to: Recommendation for air system parts

    Push-on fittings with DOT compression fittings.

  • Dick

    Member
    March 2, 2020 at 10:19 pm in reply to: Another radiator leak!

    Radiator, CAC, etc removed today.

    Apparently the fan clutch made contact with brace across the radiator, the fins were broken off, and the pieces were propelled in the radiator.

    They also found what they think is a pin hole in lower part of the radiator (separate problem). They also found deterioration in the radiator fins in the other lower corner.

    So today we ordered a new fan clutch hub, fan blade, gearbox belts, and fan belt from Prevost. The gear box is in California.

    Tomorrow morning the radiator heads to the radiator shop in San Antonio for a new core.

    Tomorrow I’ll try to figure out why the fan clutch hub made contact with the radiator strut.

    Appreciate hearing from anyone with a previous experience.

  • Dick

    Member
    March 2, 2020 at 8:59 pm in reply to: Changes to 2006 Prevost shell

    06 Chassis had last generation slides

    late in year chassis had multiplex wiring but very few

    like mentioned slides were biggest change

    Later

    bv

  • Dick

    Member
    March 2, 2020 at 4:53 pm in reply to: Detroit Allison service

    When I was in Houston last year, Stewart Stevenson was too busy to get to me. I was told by Prevost Houston that S&S in that area stays very busy with oil field and marine work. Mid Coast Diesel did the work on mine. They also work mostly in marine and oil field, but they sent a man right to me. Their yard is not very big, but they came to Prevost to do it.

Page 52 of 214