Forum Replies Created

Page 48 of 214
  • Dick

    Member
    April 20, 2020 at 2:08 pm in reply to: Amana fridge

    Thank you sir

  • Dick

    Member
    April 19, 2020 at 6:29 pm in reply to: Dash air fan motor replacement

    Doug, your da man!

    Here is what I would use to pull 3/16″ stainless rivets. Harbor Freight air riveter – $40 I used one when I rebuilt a trailer ramp door and I needed to pull about 200 3/16″ stainless blind rivets. If I would have pulled them by hand I would still be sporting forearms like Popeye.

  • Dick

    Member
    April 19, 2020 at 4:54 pm in reply to: Trouble at FMCA

    Does anyone have access to the FMCA financials? Is FMCA a for profit business? Not for profit (non-charity)? Non-profit (501(c)3 charity?)

    Sounds like FMCA for some reason might have been too thinly capitalized and did not have enough cash in reserve to weather rough times.

    I’m treasurer or an officer of three non-profit motorsports organizations (one is a true 501(c)3). They are fairly small in comparison to FMCA. Because of my back ground in banking everyone looks to me for advice and counsel on how much cash we should have. Frankly … cash is like horsepower at the race track: You can never, ever have enough.

    My standard answer has been simple:

    1. Presume no income for one or two years.

    2. Presume full operating expenses during that time period, no attempt to reduce costs.

    3. How much cash do you need to stay in business.

    We’ve typically carried two to five years based on that for each organization. After concluding that discussion someone usually says, “Thank the good Lord we’ll never be in an environment like that ever.” Then everyone laughs and we move on to the next item on the agenda.

    This year … NO ONE is laughing.

  • Dick

    Member
    April 19, 2020 at 1:47 pm in reply to: covid 19 update
  • Dick

    Member
    April 19, 2020 at 10:04 am in reply to: covid 19 update

    Just something to think about. The number of deaths claimed from Cv have been skewed by hospitals ,etc so they will receive 15% more stimulus $$. NY governor reported their death accounting method has been revised which resulted in increased totals. Are all these deaths really associated with CV ? Symptoms vary with persons. Are the test results accurate ? How do the number of cases compare to other yearly viruses ? Is this a fabricated pandemic for political reasons? Time will tell all.

  • Dick

    Member
    April 19, 2020 at 1:45 am in reply to: covid 19 update

    Fred,

    Thank you for sending this to me …

  • Dick

    Member
    April 17, 2020 at 12:19 pm in reply to: Crazy time to hunt for a coach…

    There’s a 2008 XLII non-slide Outlaw for sale.

    Be aware it’s a 2004 chassis, know what your buying.

    Later

    bv

  • Dick

    Member
    April 16, 2020 at 6:52 pm in reply to: Where to get the correct fittings?

    Les, I make the comment driven by two things. First it relates to unfinished aluminum, and most of what we come in contact with has had some surface treatment such as anodizing.

    Out coaches have some aluminum parts, and I am thinking specifically of things like the boxed awnings like my Zip Dee. The end caps are almost eaten away despite having had a painted surface. When the paint bubbles and lifts off there is literally white corrosion and most of the aluminum eaten away.

    Raw aluminum, like the inside of a tank does corrode. The inside of Norgrens corrode. Any moisture that is not at a ph of 7 is going to accelerate aluminum corrosion.

  • Dick

    Member
    April 15, 2020 at 5:53 pm in reply to: 6 o’clock news tonight in the land of OZ

    Jeff … oh!

    Boat: 62mph (early 70’s)

    Water skiing: 80mph (estimated, early 70’s)

    Floatplane (on water): 80kts

    Snowmobile: 92mph

    Street car: 125mph

    Milwaukee Mile oval: 146mph (vintage Cup car)

    Road America: 165+/-mph (vintage Cup car, ARCA, Xfinity)

    Indianapolis Motor Speedway (oval): 177mph (vintage Cup car, restricted by no passing in corner rules)

    Daytona International Speedway (oval): 173mph lap average/184mph top end (ARCA test in Willie Mullins second car that finished 9th in 2018 ARCA 200 with Andrew Belmont at the wheel)

    Bonneville Salt Flats: TBD at some point (likely the vintage Cup car)

  • Dick

    Member
    April 15, 2020 at 5:43 pm in reply to: 6 o’clock news tonight in the land of OZ

    Dick, i think the idea is share ones respective top speed in a car. If you wish to share im sure many would be interested.

  • Dick

    Member
    April 15, 2020 at 4:00 pm in reply to: 6 o’clock news tonight in the land of OZ

    Biggest problem Mango and I had was do we borrow the red one or the black one.

    Life is good in DeSilva land… I think 120 was 2nd gear.

  • Dick

    Member
    April 14, 2020 at 6:31 pm in reply to: Amana fridge

    Most of us with the Amana vintage fridges just replace them, parts are almost impossible to find and it’s a non ending battle.

  • Dick

    Member
    April 14, 2020 at 2:42 pm in reply to: Where to get the correct fittings?

    Can I ask why your combining your Prevost air and Marathon Aux air with your yellow valve?

    That should be a no no.

    Later

    bv

  • Dick

    Member
    April 14, 2020 at 2:06 pm in reply to: Where to get the correct fittings?

    Thank you everyone for your suggestions.

    I went to Fleetpride and replaced 3 fittings with compression fittings.

  • Dick

    Member
    April 13, 2020 at 4:49 pm in reply to: Water tank drain

    I guess I better look at my screens. I thought there was a screen to dump holding tanks, but I was unaware the fresh water could be dumped as well.

    I thought I only had four options: Port Dump, Starboard Dump, Macerator, Grey water By-Pass.

    I’m not one to dump from a screen. I want to be right at the hose when I dump in case I have to close the valve quickly.

    But I do see the benefit of dumping while driving when some moron driver just will not stop tailgating. Gotta try that some time.

Page 48 of 214