Dick
Forum Replies Created
-
Dick
MemberOctober 16, 2015 at 3:22 pm in reply to: Spending the day at American Fleet Diesel ServiceBrian: I used the term “pallet” generically to describe a device used as a base on which to fasten something for shipping. Please note the my italicized edit above.
When I was in the airplane business we regularly shipped and transported Pratt & Whitney 450hp R-985 radial engines on a pallet to which a wooden fixture with hold down bolts had been securely fastened. Worked pretty slick. I regularly hauled two engines on their fancy pallets in the back of a half ton pickup truck. At the time mid-1970s I was told a freshly overhauled engine was worth over $10,000.
You might want to post a picture of the steel tube shipping cradle that you use for the PC Forum members to see.
Keep up the good work!
-
Dick
MemberOctober 16, 2015 at 1:52 pm in reply to: Spending the day at American Fleet Diesel ServiceBrian: NONE of us ever want to see our engine/transmission package on a proprietary steel tube frame
pallet. But in a worst case scenario, we have comfort in knowing where to find you. -
Backing a trailer with the bus is not hard if you react quickly and appropriately when you need to adjust the direction the trailer is going.
When we were building our house I rented a short U-Haul trailer and filled it with all the electrical stuff. We were building power outlets so I had access to everything needed to completely wire the house and bus garage at OEM prices. On the way down I spent the night in a truck stop and when I wanted to pull out I headed toward the exit and found it was blocked by a truck that had a problem. So I had to back up the entire length of the truck stop, a 40 foot bus with a 10 foot trailer. For me the key was to just keep my hand on the bottom of the steering wheel and I pushed the steering wheel in whatever direction I wanted the trailer to go.
I use the same practice when backing my pickup or dump truck up the driveway with a trailer hitched on.
I think the people with problems react too slowly and over think the process.
-
Wellnuts, now I know, thanks
Dick, Mine weren’t stainless I didn’t have the corrosion problem u mentioned. Our whole coach is pretty much corrion free
-
Thank you all for the advice. After 3 months I finally got it to work. I have to keep the center on low and then it will work. thanks again.
-
Jon, Dick:
When I had my 154 site park and the co-driver got out with a walkie talkie, I got on the golf cart and got out of plate throwing range, because before the rig was parked, the air was gonna be blue and plates would soon start to fly.
One day a really long fifth wheel came in and I showed him the pull thru site. He ask if he could come down the other road and back in…SURE, what ever you want. So he comes in the other road, his wife gets out with the walkie talkie and I start to get nervous. She walks over, looks at the site and keys the mike and says…OK. He pulls forward to a certain point and she again keys the mike and says…OK. He starts to back up to his blind side, she keys the mike and says…Tighten it up…..Ease off……Straighten it out……Stop. It was done! I suggested that the two of them start a school instructing fifth wheelers how to drive and back up. He explained that they had spent several Sundays in a large store parking lot with water filled milk jugs as markers.
As he said, the spotter does not need to give driving instructions over the walkie talkie. No need to say “Take you foot off the brake, move it over the accelerator and press down 3/8 of an inch.” The driver knows they need to go forward, or backward, so after looking at the site and deciding how you want the rig in it, you simply say OK. He said that they had agreed on about 10 words that they BOTH knew what they ment and only used them. None of the old “Turn Right”…My right? or Your right? since we are looking at each other. Or, my favorite, one hand motioning to the right with the other hand motionng to the left, meaning move that way (right) because you are too far over that way (left). (actually happened)
I do have to commend the Canadians as they all seem to know how to back a rig. Maybe it is because they used to have only back in spots in parks.
Fred
-
You can buy the rubber well nuts from Prevost
-
Been down the Auto-Awning path on our prior coach (Foretravel). After 9 years of bitching and moaning, we replaced it with a manual Zip Dee. Best move we ever did. Now, for the president of Zip Dee.. Complete jackass. He wanted our auto awning, arms, tube, motor… James Stallings removed it all and I paid to have it shipped to Zip Dee as they were going to give me credit.. After numerous unreturned phone calls and a letter to the president, I am still waiting on my credit!
When looking for our bus, I ruled out any coach with that awning, which meant no Liberty’s for the range we were looking..
-
Steve and Jon are right. And to add insult to injury … the arms aren’t even polished copper!
-
They look great.
Any tips for the install?
-
Buddy, I found a “wide spot” in the road and jacked the 45 footer around and got out. The next time I came back to get the bus I took the truck down the same road to see if I could have made it or not. This being my first solo flight in the beast I may not have made it. Although Jeff’s boys said I could have done it. Maybe if it was day time and not in the snow!!
-
Jon,
We have to find a way to charge these guys dues, especially Colt.
-
I think I may have been guilty…guilty…guilty
Sorry..ty
-
Very impressive. You don’t have to back up!
-
This is one of the six trucks we use for that kind of job

its a 60 ton sliding rotater 360 degrees