Archived
Forum Replies Created
-
You would have to set your inverters on 30 amp shore cord size and then 15 amp max on each inverter. If the inverters are still passing power, your problem is likely the GFCI.
Did you talk to Marathon?
-
Over the years I have done a lot of stuff on various coaches. Clearly the two best solutions for work under the chassis are a pit or wheel lift. Neither is perfect. They each have very serious differences and it is those differences that make the choice of one or the other important.
A pit with a width of 24″ allows full chassis support as well as a means of lifting a tire off the floor. Unfortunately a pit does not allow lifting so that things like removing a fuel tank are possible. The height of the coach is fixed, meaning to get the area being worked on up or down is limited to the distance the chassis will raise or lower.
A wheel lift allows an almost unlimited variation in height from the floor. That means almost any under chassis work can be done at the most convenient height. But there are downsides. A lift requires a very high ceiling. A lift cannot be used if the tires and wheels have to be removed.
Unfortunately unless a shop has a pit and wheel lifts service work is going to be a compromise.
-
I suspect there will be lots of used wheel lifts for sale as seated coach operators go out of business, retire and sell of the coaches, consolidate, etc.
With a very few exceptions … the seated coach and entertainer coach businesses has run into a brick wall.
-
I agree with Buddy. You shouldn’t have more than one GFI or CFCI on a circuit/breaker. His suggestion to start at the outlet and work backwards is a good one! If you end up replacing any outlet … do NOT use back stab outlets; they will work loose over time especially in a coach. Back wiring or maybe ring terminals on the side posts is the way to go!
I was originally told and then then learned that you get what you pay for when it comes to electrical outlets. I don’t know what level of quality of outlets your converter put in, but (1) if they used cheap outlets that could be the problem or (2) the outlets are aged and getting soft.
Other posters will correct me if I’m wrong …. 30amp shore power is substantially less power than 50amp. 30amp is typically only a single 120volt leg where 50amp is typically TWO 120 volt legs. So 30amps is 30 amps and 50amps is a total of 100amps. So its likely between the trailer and whatever the coach was pulling from shore power … more than 30 amps was pulled and something “tripped” somewhere.
Lots of good suggestions of where to look!
-
That theory is actually fact. You figured it out. I learned this the same way you are.. lol
-
Lots of good points. Experimental aircraft do have to go through a mandatory airworthiness inspection before they can be test flown. But the mandatory sticker that “This aircraft does not comply with FAA regulations for standard aircraft” does raise passenger eyebrows I’m sure.
As I understand, you become your own test pilot for the first 40 hours. No passengers and there are limitation on where you can go. Only fair I guess. You build it, you fly it first.
The advantage of building an experimental vs buying one is that you can do your own repairs and condition inspections.
Most of the newer avionics do a much better job of identifying issues than the old analog hardware. My KFC150 autopilot kept randomly disconnecting and there was no way to find out why. I had all servos rebuilt but it still happened. It turned out the King attitude indicator was the culprit. The analog signal to the autopilot was not always stable. The avionics shop was useless in diagnosing that situation.
-
It works when I click on it?
Do a FB marketplace search using the brand name “ari hetra”. That’s the brand. There are 4 of them, asking $13k, in NY.
I hope this helps
-
That’s really cool Davy!
-
I don’t think I’ve ever met a pilot who was unhappy with their homebuilt, and most have been Van’s RV-something. When I bought my first Bonanza, it was a choice between that and an RV-8A. I went with an older V-Tail for cost and (larger) pilot comfort. The RV would have fit my mission better, and the fun factor! I’d probably buy a flying model vs. building one, but I’ll bet you’re looking forward to the challenge.
-
Forgot to put on list
had all of them done
-
20,000 rivets. Can you do them yourself? Or will you need a helper?
-
One of the best features of the Beetronics monitor is to take video inputs from a remote device and display it after selecting the new input with Beetronics remote. Here are screen shots of displaying the input from Rand McNally OVD7 GPS on bigger monitor using a Insignia Cable NS-HG1182 HDMI Micro (GPS) to HDMI (monitor). Thus I can put OverDrive 7 GPS to my left freeing up window space and just look down to my right.
-
A trip to enjoy your hard work
-
Despite the scary times, our job has had us on the road and in the public’s face since this all began. We were careful, sensable and overly cautious. We made a couple of bonehead decisions along the way and kicked ourselves in the butt everyday while we waited out the dire concequences that were possible.
Luckily, we have come through unscathed. It looks like we will have the Holiday’s off and we are enjoying Thanksgiving in Houston, TX. We might still be here for Christmas but we never know!
I hope everyone can enjoy a very happy and safe Holiday season. Even if you don’t believe there’s a problem, it’s better to be safe and enjoy many, many years to come!
HAPPY HOLIDAYS TO ALL MY PREVOST FAMILY!
-
Good idea David and the price was right.