Archived
Forum Replies Created
-
Definitely Lakeview! Great, well run park. I would guess that as many as 1/2 the folks there are being treated somewhere in the medical center. Sign up for a month and you can stay as long as necessary without anyone bugging you.
Catch the shuttle or it’s a very short drive. The only problem is trying to get back to the park around 5pm and sometimes the early morning drive in can be backed up a bit as well.
-
Thanks for the suggestions. I will try these methods and let you know.
to be clear I hear the air rush out from between the front wheels when switched from level low to drive. And I can hear the solenoids in the 4part manifold operate. Specifically the second one down and I think the 3rd. I do Cary extra norgrens (but do I have the correct one?) so I’ll swap the second one down out and see what difference it makes. I have serviced my drier and never see moisture in my system but I have suspected my aux compressor could be a source since it does not have a drier.
thanks for the input I’ll get back to you. FYI our cell tower blew over in a storm so I am slow to respond this is turning out to be quite the adventure.
thanks,
Elliot
-
Billy, Except for the big socket required for the nut no special tools will be needed and if you take your time and pay attention to detail you will have no issues.
I haven’t looked at Don’s information but one thing needs an abundance of caution and that is insuring the bearings are lubricated. My practice has been to hand pack the bearings with high temp grease prior to assembly. Then to be sure I have a belt to go with my suspenders I make an effort to tip the axle as much as possible to try to get the differential grease into the hub before driving.
We have had two Prevost owners have their axle ends twisted off as a result of dry bearings after a hub seal replacement. If I remember correctly in both cases they only got about 4 miles before the bearings seized, one being on the big bridge outside of Tampa.
-
Where are you located?
-
Thanks Jon and thanks Don – great link. That’s how I discovered this leak – was changing dryer cartridge.
This whole setup seems very similar to front Dana 44 axles on 79 Fords. Outer nut, lock ring, inner nut.
The last rear seal I did on my F250 took 3 seals/tries. First went in backwards, second time after installing I left the inner bearing out. Swapped a transaxle in a fwd car – went to fasten converter and noticed flexplate laying under rear axle where I had slid it outa the way. Hopefully this goes smoother. May be next week before I get back to it.
Thanks again guys.
-
Early 2020 I changed both of my drive axle inner seals. Here’s is the PC thread I did with a lot of pics and mx manual info: LINK
-
Have the yoke changed at your local drive shaft shop. Assume you want to keep that special seal. Shop could have some good ideas to eliminate your problem.
Drive shaft shop should check for accurate spin and balance.
AL
-
Jon
Hub is (hopefully 🙂 coming off anyway – to replace leaking seal. Anything overly complicated or unexpected in regards to removing/replacing these broken studs?
Haven’t got drum off yet so cant see backside, but seems like pics I’ve seen show a nut on the backside of stud.
I probably should carry it all to shop, certainly no stranger to confrontations when warranted, as I also feel this is. Most likely depends on how complicated repair is as to whether I invest any time into doing that or not.
I did read your write-up from years back on hub seal replacement, and using a 2×6 vs a seal driver (which I don’t have that size). Very informative thank you.
-
Hi Jimmy,
You’re probably not to far from the wine trail.
Did you get hit with snow the last couple of days?
stay warm
Chris
-
Low Hanging Fruit and Lazy Mechanic
That’s me. Before swapping valves take a quick check of the four port manifold with the level low solenoid valves in the stack. Crack the second one down, (third one up) and see if in the road or driving position that valve is flowing air. If not the coil on the valve is bad and any other coil in the stack can be swapped temporarily to allow you to drive. You may see posts talking about a 5 port manifold, but your vintage had 4)
Or Bill may be on to something if the coach has moisture in the accessory system, in which case cold and freezing temps are going to drive you absolutely nuts until the air system is dried, damaged components replaced, and the air dryer serviced.
-
Richard, To the best of my knowledge your coach preceded Liberty conversions that use the large finned isolators of newer models.
Your isolator is a solenoid (relay) that is energized when the alternator has output. In other words it is in the output circuit of the alternator, but is open thus separating the house and chassis batteries from each other until the alternator has output.
If the house batteries are deeply discharged I can envision the current flowing through that relay being high, combined with old contacts with some resistance it is likely it will get warm.
Whichever means of isolation you have you know if it is working merely by using a multi-tester to measure voltage at each set of batteries and noting a voltage rise when the engine is started. If the two sets are not isolated voltage readings are going to be identical so when checking with the engine off add a load to the house batteries, or check voltage as the engine starter is engaged. In neither case should each set show the same voltage.
-
No on #379 …..I just have a collection of stuff that came with the bus from previous owners.
-
THANKS for posting. my coach #547. anymore where that came from. LOL.
-
Ed!!!
You are a champion! Followed the diagram with my multimeter in hand, probing away and BAM! Loose breaker button on the input side of a relay feed. Little spark, nice click of the relay and we are back in business. Found it 10 minutes before the electrician pulled up. Saving me quite a few bucks. We would have pulled all the GFI’s without that diagram.
Thanks very much for the look out.
L -
Not sure what you mean by “pin breakers”. From what I see, there is only the one breaker on the units. Are you meaning the push pins on the panel above the remote inverter panels in Marathon bedroom? And, yes, I pressed all those.
Thanks